1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
|
/* Copyright 2020 The ChromiumOS Authors
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Palkia board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Baseboard features */
#include "baseboard.h"
#define CONFIG_POWER_BUTTON
#define CONFIG_KEYBOARD_PROTOCOL_8042
#define CONFIG_LED_COMMON
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_HOST_INTERFACE_ESPI
#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096
/* Keyboard features */
#define CONFIG_PWM_KBLIGHT
#define CONFIG_KEYBOARD_CUSTOMIZATION
/* Enable board_config_pre_init() */
#define CONFIG_BOARD_PRE_INIT
/* USB Type C and USB PD defines */
#define CONFIG_USB_PD_COMM_LOCKED
#define CONFIG_USB_PD_TCPM_PS8751
#define BOARD_TCPC_C0_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
#define BOARD_TCPC_C0_RESET_POST_DELAY 0
#define GPIO_USB_C0_TCPC_RST GPIO_USB_C0_TCPC_RST_ODL
/* USB Type A Features */
#define CONFIG_USB_PORT_POWER_SMART
#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT
#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
#define GPIO_USB1_ILIM_SEL GPIO_USB_A_LOW_PWR_ODL
/*
* Palkia' battery takes several seconds to come back out of its disconnect
* state (~4.2 seconds on the unit I have, so give it a little more for margin).
*/
#undef CONFIG_POWER_BUTTON_INIT_TIMEOUT
#define CONFIG_POWER_BUTTON_INIT_TIMEOUT 6
/* BC 1.2 */
#define CONFIG_BC12_DETECT_PI3USB9201
/* Fan features */
#define CONFIG_FANS 1
#undef CONFIG_FAN_INIT_SPEED
#define CONFIG_FAN_INIT_SPEED 50
#define CONFIG_TEMP_SENSOR_POWER
#define CONFIG_THERMISTOR
#define CONFIG_THROTTLE_AP
#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B
/* DPTF */
#define CONFIG_DPTF_MULTI_PROFILE
/*
* Macros for GPIO signals used in common code that don't match the
* schematic names. Signal names in gpio.inc match the schematic and are
* then redefined here to so it's more clear which signal is being used for
* which purpose.
*/
#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L
#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_PG_EC_RSMRST_ODL GPIO_PG_EC_RSMRST_L
#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK
#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L
#define GPIO_TEMP_SENSOR_POWER GPIO_EN_A_RAILS
#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum adc_channel {
ADC_TEMP_SENSOR_1, /* ADC0 */
ADC_TEMP_SENSOR_2, /* ADC1 */
ADC_TEMP_SENSOR_3, /* ADC3 */
ADC_TEMP_SENSOR_4, /* ADC2 */
ADC_CH_COUNT
};
enum pwm_channel { PWM_CH_KBLIGHT, PWM_CH_FAN, PWM_CH_COUNT };
enum fan_channel {
FAN_CH_0 = 0,
/* Number of FAN channels */
FAN_CH_COUNT,
};
enum mft_channel {
MFT_CH_0 = 0,
/* Number of MFT channels */
MFT_CH_COUNT,
};
enum temp_sensor_id {
TEMP_SENSOR_1,
TEMP_SENSOR_2,
TEMP_SENSOR_3,
TEMP_SENSOR_4,
TEMP_SENSOR_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_DYNAPACK_UX48144,
BATTERY_TYPE_COUNT,
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
