blob: 0782612cb862c0d08d305d0405287a47609bf762 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
|
/* Copyright 2021 The ChromiumOS Authors
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Herobrine baseboard configuration */
#ifndef __CROS_EC_BASEBOARD_H
#define __CROS_EC_BASEBOARD_H
/*
* By default, enable all console messages excepted event and HC:
* The sensor stack is generating a lot of activity.
* They can be enabled through the console command 'chan'.
*/
#define CC_DEFAULT (CC_ALL & ~(CC_MASK(CC_HOSTCMD)))
/* NPCX7 config */
#define NPCX_UART_MODULE2 1 /* GPIO64/65 are used as UART pins. */
#define NPCX_TACH_SEL2 0 /* No tach. */
#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */
/* Internal SPI flash on NPCX7 */
#define CONFIG_SPI_FLASH_REGS
#define CONFIG_SPI_FLASH_W25Q80 /* Internal SPI flash type. */
/* EC Modules */
#define CONFIG_I2C
#define CONFIG_I2C_CONTROLLER
#define CONFIG_I2C_VIRTUAL_BATTERY
#define CONFIG_I2C_PASSTHRU_RESTRICTED
#define CONFIG_LED_COMMON
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_ADC
#define CONFIG_BACKLIGHT_LID
#define CONFIG_FPU
#define CONFIG_PWM
#define CONFIG_PWM_DISPLIGHT
#define CONFIG_HIBERNATE_PSL
#define CONFIG_VBOOT_HASH
#undef CONFIG_PECI
#define CONFIG_HOST_INTERFACE_SHI
#define CONFIG_HOST_COMMAND_STATUS
#define CONFIG_HOSTCMD_SECTION_SORTED
#define CONFIG_KEYBOARD_COL2_INVERTED
#define CONFIG_MKBP_USE_GPIO
#define CONFIG_BOARD_VERSION_GPIO
#define CONFIG_CBI_GPIO
#define CONFIG_CRC8
#define CONFIG_POWER_BUTTON
#define CONFIG_VOLUME_BUTTONS
#define CONFIG_EMULATED_SYSRQ
#define CONFIG_CMD_BUTTON
#define CONFIG_SWITCH
#define CONFIG_LID_SWITCH
#define CONFIG_EXTPOWER_GPIO
/*
* On power-on, H1 releases the EC from reset but then quickly asserts and
* releases the reset a second time. This means the EC sees 2 resets:
* (1) power-on reset, (2) reset-pin reset. This config will
* allow the second reset to be treated as a power-on.
*/
#define CONFIG_BOARD_RESET_AFTER_POWER_ON
/* Increase console output buffer since we have the RAM available. */
#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096
/* Battery */
#define CONFIG_BATTERY_CUT_OFF
#define CONFIG_BATTERY_PRESENT_GPIO GPIO_BATT_PRES_ODL
#define CONFIG_BATTERY_SMART
/* Charger */
#define CONFIG_CHARGER
#define CONFIG_CHARGE_MANAGER
#define CONFIG_CHARGER_ISL9238
#define CONFIG_CHARGER_PROFILE_OVERRIDE
#define CONFIG_CHARGE_RAMP_HW
#define CONFIG_USB_CHARGER
#define CONFIG_CMD_CHARGER_ADC_AMON_BMON
#define CONFIG_CHARGER_PSYS
#define CONFIG_CHARGER_PSYS_READ
#define CONFIG_CHARGER_DISCHARGE_ON_AC
#define CONFIG_CHARGER_INPUT_CURRENT 512
#define CONFIG_CHARGER_MIN_POWER_MW_FOR_POWER_ON 10000
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20
/*
* USB ID
*
* This is allocated specifically for Herobrine
* http://google3/hardware/standards/usb/
*/
#define CONFIG_USB_PID 0x5055
/* USB */
#define CONFIG_USB_POWER_DELIVERY
#define CONFIG_USB_PD_TCPMV2
#define CONFIG_USB_DRP_ACC_TRYSRC
#define CONFIG_USB_PD_DECODE_SOP
#define CONFIG_HOSTCMD_PD_CONTROL
#define CONFIG_USB_PD_ALT_MODE
#define CONFIG_USB_PD_ALT_MODE_DFP
#define CONFIG_USB_PD_DISCHARGE_PPC
#define CONFIG_USB_PD_DUAL_ROLE
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_TCPC_LOW_POWER
#define CONFIG_USB_PD_LOGGING
#define CONFIG_USB_PD_TCPM_MUX
#define CONFIG_USB_PD_TCPM_TCPCI
#define CONFIG_CMD_TCPC_DUMP
#define CONFIG_USB_PD_TRY_SRC
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define CONFIG_USB_PD_5V_EN_CUSTOM
#define CONFIG_USBC_SS_MUX
#define CONFIG_USBC_SS_MUX_DFP_ONLY
#define CONFIG_USBC_VCONN
#define CONFIG_USBC_VCONN_SWAP
/* RTC */
#define CONFIG_CMD_RTC
#define CONFIG_HOSTCMD_RTC
/* Sensors */
/* Enable sensor fifo, must also define the _SIZE and _THRES */
#define CONFIG_ACCEL_FIFO
/* FIFO size is a power of 2. */
#define CONFIG_ACCEL_FIFO_SIZE 256
/* Depends on how fast the AP boots and typical ODRs. */
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
/* PD */
#define PD_POWER_SUPPLY_TURN_ON_DELAY 30000 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 250000 /* us */
#define PD_OPERATING_POWER_MW 10000
#define PD_MAX_POWER_MW ((PD_MAX_VOLTAGE_MV * PD_MAX_CURRENT_MA) / 1000)
#define PD_MAX_CURRENT_MA 3000
#define PD_MAX_VOLTAGE_MV 20000
/* Chipset */
#define CONFIG_CHIPSET_SC7280
#define CONFIG_CHIPSET_RESET_HOOK
#define CONFIG_CHIPSET_RESUME_INIT_HOOK
#define CONFIG_POWER_COMMON
#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE
#define CONFIG_POWER_SLEEP_FAILURE_DETECTION
#define CONFIG_CMD_AP_RESET_LOG
/*
* Macros for GPIO signals used in common code that don't match the
* schematic names. Signal names in gpio.inc match the schematic and are
* then redefined here to so it's more clear which signal is being used for
* which purpose.
*/
#define GPIO_POWER_BUTTON_L GPIO_EC_PWR_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_LID_OPEN GPIO_LID_OPEN_EC
#define GPIO_SHI_CS_L GPIO_AP_EC_SPI_CS_L
#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW
#define GPIO_BATT_PRES_ODL GPIO_EC_BATT_PRES_ODL
#define GPIO_ENABLE_BACKLIGHT GPIO_EC_BL_DISABLE_L
#define GPIO_BOARD_VERSION1 GPIO_BRD_ID0
#define GPIO_BOARD_VERSION2 GPIO_BRD_ID1
#define GPIO_BOARD_VERSION3 GPIO_BRD_ID2
#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV
/* I2C Ports */
#define I2C_PORT_BATTERY I2C_PORT_POWER
#define I2C_PORT_VIRTUAL_BATTERY I2C_PORT_BATTERY
#define I2C_PORT_CHARGER I2C_PORT_POWER
#define I2C_PORT_ACCEL I2C_PORT_SENSOR
#define I2C_PORT_POWER NPCX_I2C_PORT0_0
#define I2C_PORT_TCPC0 NPCX_I2C_PORT1_0
#define I2C_PORT_TCPC1 NPCX_I2C_PORT2_0
#define I2C_PORT_WLC NPCX_I2C_PORT3_0
#define I2C_PORT_RTC NPCX_I2C_PORT4_1
#define I2C_PORT_EEPROM NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR NPCX_I2C_PORT7_0
/* UART */
#define CONFIG_CMD_CHARGEN
/* Define the host events which are allowed to wake AP up from S3 */
#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \
(EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_CONNECTED) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_DISCONNECTED) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_HANG_DETECT) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_RTC) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_MODE_CHANGE) | \
EC_HOST_EVENT_MASK(EC_HOST_EVENT_DEVICE))
/* And the MKBP events */
#ifdef HAS_TASK_KEYSCAN
#define CONFIG_MKBP_EVENT_WAKEUP_MASK \
(BIT(EC_MKBP_EVENT_KEY_MATRIX) | BIT(EC_MKBP_EVENT_HOST_EVENT) | \
BIT(EC_MKBP_EVENT_SENSOR_FIFO))
#else
#define CONFIG_MKBP_EVENT_WAKEUP_MASK \
(BIT(EC_MKBP_EVENT_HOST_EVENT) | BIT(EC_MKBP_EVENT_SENSOR_FIFO))
#endif
#endif /* __CROS_EC_BASEBOARD_H */
|
