summaryrefslogtreecommitdiff
path: root/driver
Commit message (Expand)AuthorAgeFilesLines
* ctn730: Print firmware versionstabilize-quickfix-13816.67.B-mainstabilize-LTS-13816.60.B-mainstabilize-13816.82.B-mainstabilize-13816.80.B-mainstabilize-13816.64.B-mainstabilize-13816.63.B-mainstabilize-13816.55.B-mainstabilize-13816.53.B-mainstabilize-13816.51.B-mainstabilize-13816.40.B-mainrelease-R90-13816.B-mainDaisuke Nojiri2021-03-261-0/+1
* PCHG: Support reset to firmware update modeDaisuke Nojiri2021-03-251-19/+59
* PCHG: Handle reset eventDaisuke Nojiri2021-03-251-1/+10
* driver/it83xx, it8xxx2: turn on PD BMC PHY for TCPMv1Ruibin Chang2021-02-262-10/+42
* driver: tcs3400: Check for device status only onceGwendal Grignou2021-02-251-28/+31
* driver: icm426xx: discard first data instead of sleepingJean-Baptiste Maneyrol2021-02-253-22/+98
* driver: icm426xx: change accel oscillator to RC clockJean-Baptiste Maneyrol2021-02-252-1/+11
* driver: icm426xx: update odr before turning sensor onJean-Baptiste Maneyrol2021-02-251-10/+10
* RAA489000: Rearrange inits to sink Vbus fasterDiana Z2021-02-241-35/+37
* COIL: Rename GT7288 address defineDiana Z2021-02-241-3/+3
* COIL: Rename MP4245 address defineDiana Z2021-02-241-12/+12
* COIL: Rename ioexpander i2c address variableDiana Z2021-02-244-21/+21
* BB Retimer: Cleanup setting USB4 speedAyushee Shah2021-02-231-13/+5
* ln9310: set min. freq above audible rangeJohn Crossley2021-02-232-0/+7
* tca64xxa: Add new ioexpander driver for TI TCA64xxA modulesMichał Barnaś2021-02-233-0/+252
* guybrush: Add ANX7451 mux/retimer driverRob Barnes2021-02-233-0/+130
* Virtual mux: Set disconnect latch flag only in s3/s0ixAyushee Shah2021-02-221-2/+4
* raa489000 : change VBUS_CURRENT_TARGETYongBeum.Ha2021-02-211-2/+2
* bq25710: Allow compilation with CHARGE_RAMP_SWCaveh Jalali2021-02-191-0/+2
* RT1715: Enable power saving modesEric Herrmann2021-02-172-33/+114
* nb7v904m : Add function to control Loss Profile MatchingYongBeum.Ha2021-02-172-0/+39
* nb7v904m : add function to control aux channelYongBeum.Ha2021-02-172-0/+11
* nb7v904m : add config to disable LPMYongBeum.Ha2021-02-172-0/+11
* PCHG: Get SOC proactively when device is detectedDaisuke Nojiri2021-02-121-3/+27
* tusb422: Don't perform soft reset during initializationPatryk Duda2021-02-102-8/+10
* usb_mux: ps8822: Initial version of driverScott Collyer2021-02-093-0/+140
* gl3590: Add retry algorithm for port enabling procedureJan Dabros2021-02-092-4/+33
* gl3590: Add init functionJan Dabros2021-02-092-0/+50
* gl3590: Add proper delays between i2c transactionsJan Dabros2021-02-091-2/+16
* rt1715: Reset properly coming out of LPMScott Chao2021-02-091-5/+16
* driver/it83xx, it8xxx2: define delay time for Vconn below 3.3vRuibin Chang2021-02-083-22/+17
* retimer: PD port retimer firmware update supportli feng2021-02-052-0/+25
* guybrush: Add FP6 USB mux driverRob Barnes2021-02-043-0/+247
* raa489000 : Set Vbus Target VoltageYongBeum.Ha2021-02-042-0/+10
* sasuke : change prochot debounce timeYongBeum.Ha2021-02-031-1/+6
* RAA489000 : Change Charge Voltage StepYongBeum.Ha2021-02-021-1/+1
* nb7v904m : add function to tune eq and gainYongBeum.Ha2021-02-022-8/+86
* ps8815: Add workaround for incorrect CC linesKeith Short2021-02-022-1/+57
* NCT3807: Enable full VCONN protectionJacky Wang2021-02-012-0/+20
* RAA489000: Add TCPC interface to control output currentDiana Z2021-01-292-10/+33
* driver: icm426xx: Use calibration unit to set/get offsetGwendal Grignou2021-01-291-20/+13
* ctn730: Add delay between INITIALIZATION and ENABLE (2)Daisuke Nojiri2021-01-291-3/+9
* Revert "ctn730: Add delay between INITIALIZATION and ENABLE"Daisuke Nojiri2021-01-291-6/+0
* RAA489000: Organize header fileDiana Z2021-01-291-10/+13
* COIL: Rename variables in MT6360 driverDiana Z2021-01-292-10/+10
* driver: rt1715 : Improve noise rejectionBen Chen2021-01-282-19/+172
* ctn730: Add delay between INITIALIZATION and ENABLEDaisuke Nojiri2021-01-281-0/+6
* usb_mux: Use atomic_or when setting flag during muxer initPatryk Duda2021-01-281-1/+1
* max14637: call bc12_detect in VBUS off can't update charge as availableMarco Chen2021-01-281-23/+45
* ps8xxx: Set RP during LPM enter if TCPC acts as mux onlyPatryk Duda2021-01-282-1/+108
View Lorry Controller Status