summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* meep: Disable accel, gyro sensors and tablet mode switch for clamshellsstabilize-jetstream-11056.BDevin Lu2018-09-112-3/+38
* bobba: do not disable keyboard for clamshellJett Rink2018-09-101-2/+2
* octopus: disable tablet mode switch for clamshellsJett Rink2018-09-103-16/+29
* cr50: Move Virtual NVRAM indexes into header file.Louis Collard2018-09-082-19/+49
* cr50: make EC RST synchronousVadim Bendebury2018-09-081-14/+39
* grunt: Use higher priority TCPC interrupt tasks.Jonathan Brandmeyer2018-09-078-68/+12
* octopus: use higher priority TCPC interrupt tasksJett Rink2018-09-0710-65/+15
* tcpm: add TCPC RX circular buffer in ECJett Rink2018-09-073-0/+3
* host: Add dcrypto definitions that can be used by fuzzing targets.Allen Webb2018-09-071-16/+28
* rammus: add CONFIG_BOARD_VERSION_CBI to enable board version queryZhuohao Lee2018-09-071-0/+1
* Liara: Add supported batteriesJonathan Brandmeyer2018-09-052-4/+77
* ss-mux: update semantics for TCPC/MUX only used as MUXJett Rink2018-09-055-12/+10
* cr50: Make SN data available through vNVRAM.Louis Collard2018-09-051-1/+14
* cr50: Add commands to get/set serial number bits.Louis Collard2018-09-053-4/+12
* DragonEgg: Add support to Type C port 1Scott Collyer2018-09-044-2/+25
* octopus: consolidate identical definesJett Rink2018-09-046-24/+0
* octopus: enabled DPTF device orientationJett Rink2018-09-045-13/+0
* bip: add tablet mode for consistencyJett Rink2018-09-043-0/+8
* Phaser: support quick charge function of batteryHuangGe Haha2018-09-041-0/+44
* Bobba: Set motion_sensor_count to 0 for clamshellsTino Liu2018-09-041-2/+2
* servo_micro: Increase USB stream TX size to 64 bytesNicolas Boichat2018-09-041-1/+1
* cheza: Disable the base explicitly in S5Wai-Hong Tam2018-09-031-4/+17
* usb_update: add extra command "UPDATE_EXTRA_CMD_CONSOLE_READ_*"Wei-Han Chen2018-09-031-0/+2
* whiskers: Drive DETECT_PATH_DISABLE_L low, pull-up on BACKLIGHT_ENNicolas Boichat2018-09-031-1/+2
* whiskers: Disable keyboard scanning and touchpad in tablet modeNicolas Boichat2018-09-031-0/+17
* meep: Add Power LED behaviorZick Wei2018-09-023-10/+44
* rammus: Fix the dut keeps reboot due to the EC assert.Zhuohao Lee2018-09-021-6/+5
* cheza: Enable floating point unitWai-Hong Tam2018-08-311-0/+1
* cheza: Enable some button featuresWai-Hong Tam2018-08-311-0/+3
* rammus: decrease UART bufferJett Rink2018-08-311-1/+1
* nocturne: Use USBC alert signal for TCPC alert statusScott Collyer2018-08-311-10/+14
* meep: add VBUS voltage adc sensingDevin Lu2018-08-313-0/+29
* rammus: rammus: Modify TCPC port1 I2C bus to I2C0_0 from I2C0_1.michael_chen2018-08-311-1/+1
* stm32: usb_hid_touchpad: add confidenceWei-Han Chen2018-08-311-2/+2
* cheza: Measure VBUS by ADCstabilize-atlas-11022.BPhilip Chen2018-08-313-2/+10
* cheza: Disable interrupts which are floating when switchcap offWai-Hong Tam2018-08-311-4/+12
* cheza: Use POWER_GOOD signal instead of AP_RST_LWai-Hong Tam2018-08-312-16/+3
* Revert "cheza: Support confirmation of power lost"Wai-Hong Tam2018-08-311-1/+1
* nocturne: switch from tablet mode to base state reportingDmitry Torokhov2018-08-312-11/+4
* bobba: Add support for BMI160 base sensorsstabilize-11020.BJustin TerAvest2018-08-303-20/+21
* nautilus: decrease UART bufferJett Rink2018-08-301-1/+1
* Rammus: enable cbi for EEPROMZhuohao Lee2018-08-301-0/+4
* atlas: add ACOK as wake-from-hibernate sourceCaveh Jalali2018-08-302-3/+3
* atlas: add LID as wake-from-hibernate sourceCaveh Jalali2018-08-291-1/+4
* cr50: Release EC Reset on power button release when SuzyQ detected.Nick Sanders2018-08-293-0/+54
* cheza: Support base detectionWai-Hong Tam2018-08-294-2/+194
* kukui: Change FORCE_RESET to ODLNicolas Boichat2018-08-291-1/+1
* servo_micro: Allow setting the baud rate for usartNicolas Boichat2018-08-291-1/+34
* cheza: Add more power signals for informative purposeWai-Hong Tam2018-08-293-7/+16
* kukui: Enable CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLEYilun Lin2018-08-291-0/+1
View Lorry Controller Status