diff options
Diffstat (limited to 'board/storo/gpio.inc')
| -rw-r--r-- | board/storo/gpio.inc | 61 |
1 files changed, 32 insertions, 29 deletions
diff --git a/board/storo/gpio.inc b/board/storo/gpio.inc index c37959dc16..00a3e94289 100644 --- a/board/storo/gpio.inc +++ b/board/storo/gpio.inc @@ -1,6 +1,6 @@ /* -*- mode:c -*- * - * Copyright 2020 The Chromium OS Authors. All rights reserved. + * Copyright 2021 The Chromium OS Authors. All rights reserved. * Use of this source code is governed by a BSD-style license that can be * found in the LICENSE file. */ @@ -20,18 +20,17 @@ GPIO_INT(PG_DRAM_OD, PIN(D, 3), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrup GPIO_INT(PG_PP1050_ST_OD, PIN(L, 1), GPIO_INT_BOTH, power_signal_interrupt) GPIO_INT(VCCIN_AUX_VID1, PIN(K, 1), GPIO_INT_BOTH, power_signal_interrupt) GPIO_INT(PG_VCCIO_EXT_OD, PIN(D, 7), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt) -GPIO_INT(ESPI_RESET_L, PIN(D, 2), GPIO_INT_FALLING | GPIO_SEL_1P8V, espi_reset_pin_asserted_interrupt) +GPIO_INT(ESPI_RESET_L, PIN(D, 2), GPIO_INT_FALLING | GPIO_SEL_1P8V, espi_reset_pin_asserted_interrupt) GPIO_INT(H1_EC_PWR_BTN_ODL, PIN(E, 2), GPIO_INT_BOTH | GPIO_PULL_UP, power_button_interrupt) #ifdef CONFIG_LOW_POWER_IDLE /* Used to wake up the EC from Deep Doze mode when writing to console */ -GPIO_INT(UART1_RX, PIN(B, 0), GPIO_INT_BOTH, uart_deepsleep_interrupt) /* UART_DBG_TX_EC_RX */ +GPIO_INT(UART1_RX, PIN(B, 0), GPIO_INT_BOTH, uart_deepsleep_interrupt) /* UART_DBG_TX_EC_RX */ #endif /* USB-C interrupts */ GPIO_INT(USB_C0_INT_ODL, PIN(K, 0), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c0_interrupt) /* BC12 and charger */ -GPIO_INT(USB_C1_INT_V0_ODL, PIN(B, 5), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c1_interrupt) /* TCPC, charger, BC12 - board version 0 */ -GPIO_INT(USB_C1_INT_V1_ODL, PIN(E, 6), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c1_interrupt) /* TCPC, charger, BC12 - board version 1 */ +GPIO_INT(SUB_USB_C1_INT_ODL, PIN(E, 6), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c1_interrupt) GPIO_INT(USB_C0_CCSBU_OVP_ODL, PIN(K, 6), GPIO_INT_FALLING | GPIO_PULL_UP, c0_ccsbu_ovp_interrupt) /* Fault protection */ /* Other interrupts */ @@ -39,8 +38,9 @@ GPIO_INT(LID_OPEN, PIN(F, 3), GPIO_INT_BOTH, lid_interrupt) GPIO_INT(LID_360_L, PIN(A, 7), GPIO_INT_BOTH, gmr_tablet_switch_isr) GPIO_INT(VOLDN_BTN_ODL, PIN(I, 6), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) GPIO_INT(VOLUP_BTN_ODL, PIN(I, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(BASE_SIXAXIS_INT_L, PIN(J, 0), GPIO_INT_FALLING | GPIO_SEL_1P8V, lsm6dsm_interrupt) +GPIO_INT(BASE_SIXAXIS_INT_L, PIN(J, 0), GPIO_INT_FALLING | GPIO_SEL_1P8V, bmi160_interrupt) GPIO_INT(EC_WP_OD, PIN(A, 6), GPIO_INT_BOTH, switch_interrupt) +GPIO_INT(PEN_DET_ODL, PIN(J, 1), GPIO_INT_BOTH | GPIO_PULL_UP, pen_detect_interrupt) /* Power sequence GPIOs */ GPIO(EC_AP_RTCRST, PIN(K, 2), GPIO_OUT_LOW) @@ -78,45 +78,51 @@ GPIO(EC_I2C_SUB_USB_C1_SCL, PIN(E, 0), GPIO_INPUT) GPIO(EC_I2C_SUB_USB_C1_SDA, PIN(E, 7), GPIO_INPUT) GPIO(EC_I2C_USB_C0_SCL, PIN(A, 4), GPIO_INPUT) GPIO(EC_I2C_USB_C0_SDA, PIN(A, 5), GPIO_INPUT) - -/* USB pins */ -GPIO(EN_USB_C0_CC1_VCONN, PIN(H, 4), GPIO_OUT_LOW) -GPIO(EN_USB_C0_CC2_VCONN, PIN(H, 6), GPIO_OUT_LOW) GPIO(EC_AP_USB_C0_HPD, PIN(L, 4), GPIO_OUT_LOW) GPIO(EC_AP_USB_C1_HDMI_HPD, PIN(K, 7), GPIO_OUT_LOW) -GPIO(USB_C0_FRS, PIN(C, 4), GPIO_OUT_LOW) -GPIO(HDMI_SEL_L, PIN(C, 6), GPIO_OUT_HIGH) GPIO(EN_USB_A0_VBUS, PIN(L, 6), GPIO_OUT_LOW) /* Board rev 1, NC board rev 0 */ /* MKBP event synchronization */ -GPIO(EC_AP_MKBP_INT_L, PIN(L, 5), GPIO_ODR_HIGH) +GPIO(EC_AP_MKBP_INT_L, PIN(L, 5), GPIO_ODR_HIGH) -/* Misc pins which will run to the I/O board */ -GPIO(EC_SUB_IO_1_1, PIN(L, 3), GPIO_INPUT) -GPIO(EC_SUB_IO_1_2, PIN(F, 0), GPIO_INPUT) -GPIO(EC_SUB_IO_2_1, PIN(F, 1), GPIO_INPUT) -GPIO(EC_SUB_IO_2_2, PIN(L, 2), GPIO_INPUT) /* Misc */ GPIO(EN_BL_OD, PIN(K, 4), GPIO_ODR_LOW) GPIO(EC_ENTERING_RW, PIN(G, 0), GPIO_OUT_LOW) GPIO(CCD_MODE_ODL, PIN(H, 5), GPIO_INPUT) GPIO(EC_BATTERY_PRES_ODL, PIN(I, 4), GPIO_INPUT) -GPIO(PEN_DET_ODL, PIN(J, 1), GPIO_INPUT | GPIO_PULL_UP) -GPIO(EN_KB_BL, PIN(J, 3), GPIO_OUT_LOW) /* Currently unused */ +GPIO(EN_PP3300_PEN, PIN(B, 5), GPIO_OUT_LOW) GPIO(ECH1_PACKET_MODE, PIN(H, 1), GPIO_OUT_LOW) +/* LED */ +GPIO(LED_COLOR_AMBER, PIN(A, 1), GPIO_OUT_HIGH) +GPIO(LED_COLOR_WHITE, PIN(A, 2), GPIO_OUT_HIGH) + /* NC pins, enable internal pull-down to avoid floating state. */ +GPIO(GPIOA3_NC, PIN(A, 3), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOC0_NC, PIN(C, 0), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOC3_NC, PIN(C, 3), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOC4_NC, PIN(C, 4), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOC6_NC, PIN(C, 6), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOC7_NC, PIN(C, 7), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOF0_NC, PIN(F, 0), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOF1_NC, PIN(F, 1), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOF4_NC, PIN(F, 4), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOF5_NC, PIN(F, 5), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOG3_NC, PIN(G, 3), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOG4_NC, PIN(G, 4), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOG5_NC, PIN(G, 5), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOG6_NC, PIN(G, 6), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOG7_NC, PIN(G, 7), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOH2_NC, PIN(H, 2), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOH4_NC, PIN(H, 4), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOH6_NC, PIN(H, 6), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOJ3_NC, PIN(J, 3), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOJ4_NC, PIN(J, 4), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOJ5_NC, PIN(J, 5), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOJ6_NC, PIN(J, 6), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOL0_NC, PIN(L, 0), GPIO_INPUT | GPIO_PULL_DOWN) +GPIO(GPIOL3_NC, PIN(L, 3), GPIO_INPUT | GPIO_PULL_DOWN) GPIO(GPIOM6_NC, PIN(M, 6), GPIO_INPUT | GPIO_PULL_DOWN) /* Alternate functions GPIO definitions */ @@ -124,15 +130,12 @@ GPIO(GPIOM6_NC, PIN(M, 6), GPIO_INPUT | GPIO_PULL_DOWN) ALTERNATE(PIN_MASK(B, BIT(0) | BIT(1)), 0, MODULE_UART, 0) /* UART for debug */ /* I2C */ -ALTERNATE(PIN_MASK(B, BIT(3) | BIT(4)), 0, MODULE_I2C, 0) /* I2C0 */ -ALTERNATE(PIN_MASK(C, BIT(1) | BIT(2)), 0, MODULE_I2C, 0) /* I2C1 */ -ALTERNATE(PIN_MASK(F, BIT(6) | BIT(7)), 0, MODULE_I2C, GPIO_SEL_1P8V) /* I2C2 - 1.8V */ -ALTERNATE(PIN_MASK(E, BIT(0) | BIT(7)), 0, MODULE_I2C, 0) /* I2C4 */ -ALTERNATE(PIN_MASK(A, BIT(4) | BIT(5)), 0, MODULE_I2C, 0) /* I2C5 */ +ALTERNATE(PIN_MASK(B, BIT(3) | BIT(4)), 0, MODULE_I2C, 0) /* I2C0 EEPROM */ +ALTERNATE(PIN_MASK(C, BIT(1) | BIT(2)), 0, MODULE_I2C, 0) /* I2C1 BATTERY */ +ALTERNATE(PIN_MASK(F, BIT(6) | BIT(7)), 0, MODULE_I2C, GPIO_SEL_1P8V) /* I2C2 - 1.8V SENSOR */ +ALTERNATE(PIN_MASK(E, BIT(0) | BIT(7)), 0, MODULE_I2C, 0) /* I2C4 SUB_USB_C1 */ +ALTERNATE(PIN_MASK(A, BIT(4) | BIT(5)), 0, MODULE_I2C, 0) /* I2C5 USB_C0 */ /* ADC */ -ALTERNATE(PIN_MASK(L, BIT(0)), 0, MODULE_ADC, 0) /* ADC13: EC_SUB_ANALOG */ +ALTERNATE(PIN_MASK(L, BIT(2)), 0, MODULE_ADC, 0) /* ADC15:TEMP_SENSOR3 */ ALTERNATE(PIN_MASK(I, BIT(0) | BIT(2) | BIT(3)), 0, MODULE_ADC, 0) /* ADC0: EC_VSNS_PP3300_A, ADC2: TEMP_SENSOR_1, ADC3: TEMP_SENSOR_2 */ - -/* PWM */ -ALTERNATE(PIN_MASK(A, BIT(0) | BIT(1) | BIT(2) | BIT(3)), 0, MODULE_PWM, 0) /* KB_BL_PWM, LED_[R,G,B]_ODL */ |