summaryrefslogtreecommitdiff
path: root/board/kindred
diff options
context:
space:
mode:
Diffstat (limited to 'board/kindred')
-rw-r--r--board/kindred/battery.c94
-rw-r--r--board/kindred/board.c661
-rw-r--r--board/kindred/board.h188
-rw-r--r--board/kindred/build.mk15
-rw-r--r--board/kindred/ec.tasklist26
-rw-r--r--board/kindred/gpio.inc146
-rw-r--r--board/kindred/led.c81
-rw-r--r--board/kindred/vif_override.xml3
8 files changed, 0 insertions, 1214 deletions
diff --git a/board/kindred/battery.c b/board/kindred/battery.c
deleted file mode 100644
index 9db25ac059..0000000000
--- a/board/kindred/battery.c
+++ /dev/null
@@ -1,94 +0,0 @@
-/* Copyright 2019 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Battery pack vendor provided charging profile
- */
-
-#include "battery_fuel_gauge.h"
-#include "common.h"
-#include "util.h"
-
-/*
- * Battery info for all Hatch battery types. Note that the fields
- * start_charging_min/max and charging_min/max are not used for the charger.
- * The effective temperature limits are given by discharging_min/max_c.
- *
- * Fuel Gauge (FG) parameters which are used for determining if the battery
- * is connected, the appropriate ship mode (battery cutoff) command, and the
- * charge/discharge FETs status.
- *
- * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery
- * register. For some batteries, the charge/discharge FET bits are set when
- * charging/discharging is active, in other types, these bits set mean that
- * charging/discharging is disabled. Therefore, in addition to the mask for
- * these bits, a disconnect value must be specified. Note that for TI fuel
- * gauge, the charge/discharge FET status is found in Operation Status (0x54),
- * but a read of Manufacturer Access (0x00) will return the lower 16 bits of
- * Operation status which contains the FET status bits.
- *
- * The assumption for battery types supported is that the charge/discharge FET
- * status can be read with a sb_read() command and therefore, only the register
- * address, mask, and disconnect value need to be provided.
- */
-const struct board_batt_params board_battery_info[] = {
- /* LGC AP18C8K Battery Information */
- [BATTERY_LGC_AP18C8K] = {
- .fuel_gauge = {
- .manuf_name = "LGC KT0030G020",
- .ship_mode = {
- .reg_addr = 0x3A,
- .reg_data = { 0xC574, 0xC574 },
- },
- .fet = {
- .reg_addr = 0x43,
- .reg_mask = 0x0001,
- .disconnect_val = 0x0,
- },
- },
- .batt_info = {
- .voltage_max = 13050,
- .voltage_normal = 11250,
- .voltage_min = 9000,
- .precharge_current = 256,
- .start_charging_min_c = 0,
- .start_charging_max_c = 50,
- .charging_min_c = 0,
- .charging_max_c = 60,
- .discharging_min_c = -20,
- .discharging_max_c = 75,
- },
- },
-
- /* Murata AP18C4K Battery Information */
- [BATTERY_MURATA_AP18C4K] = {
- .fuel_gauge = {
- .manuf_name = "Murata KT00304012",
- .device_name = "AP18C4K",
- .ship_mode = {
- .reg_addr = 0x3A,
- .reg_data = { 0xC574, 0xC574 },
- },
- .fet = {
- .reg_addr = 0x0,
- .reg_mask = 0x2000,
- .disconnect_val = 0x2000,
- },
- },
- .batt_info = {
- .voltage_max = 13200,
- .voltage_normal = 11400,
- .voltage_min = 9000,
- .precharge_current = 256,
- .start_charging_min_c = 0,
- .start_charging_max_c = 50,
- .charging_min_c = 0,
- .charging_max_c = 60,
- .discharging_min_c = -20,
- .discharging_max_c = 75,
- },
- },
-};
-BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT);
-
-const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_LGC_AP18C8K;
diff --git a/board/kindred/board.c b/board/kindred/board.c
deleted file mode 100644
index c17ddb1b8a..0000000000
--- a/board/kindred/board.c
+++ /dev/null
@@ -1,661 +0,0 @@
-/* Copyright 2019 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Hatch board-specific configuration */
-
-#include "adc.h"
-#include "button.h"
-#include "common.h"
-#include "cros_board_info.h"
-#include "driver/accel_bma2x2.h"
-#include "driver/accel_kionix.h"
-#include "driver/accelgyro_bmi_common.h"
-#include "driver/accelgyro_icm_common.h"
-#include "driver/accelgyro_icm426xx.h"
-#include "driver/bc12/pi3usb9201.h"
-#include "driver/ppc/sn5s330.h"
-#include "driver/tcpm/anx7447.h"
-#include "driver/tcpm/ps8xxx.h"
-#include "driver/tcpm/tcpci.h"
-#include "ec_commands.h"
-#include "extpower.h"
-#include "fan.h"
-#include "fan_chip.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "host_command.h"
-#include "lid_switch.h"
-#include "power.h"
-#include "power_button.h"
-#include "pwm.h"
-#include "pwm_chip.h"
-#include "stdbool.h"
-#include "spi.h"
-#include "switch.h"
-#include "system.h"
-#include "tablet_mode.h"
-#include "task.h"
-#include "temp_sensor.h"
-#include "thermal.h"
-#include "temp_sensor/thermistor.h"
-#include "uart.h"
-#include "usb_charge.h"
-#include "usb_pd.h"
-#include "usbc_ppc.h"
-#include "util.h"
-
-#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args)
-#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args)
-
-static int lid_device_id;
-static int base_device_id;
-
-static void check_reboot_deferred(void);
-DECLARE_DEFERRED(check_reboot_deferred);
-
-/* GPIO to enable/disable the USB Type-A port. */
-const int usb_port_enable[CONFIG_USB_PORT_POWER_SMART_PORT_COUNT] = {
- GPIO_EN_USB_A_5V,
-};
-
-/*
- * We have total 30 pins for keyboard connecter {-1, -1} mean
- * the N/A pin that don't consider it and reserve index 0 area
- * that we don't have pin 0.
- */
-const int keyboard_factory_scan_pins[][2] = {
- {-1, -1}, {0, 5}, {1, 1}, {1, 0}, {0, 6},
- {0, 7}, {-1, -1}, {-1, -1}, {1, 4}, {1, 3},
- {-1, -1}, {1, 6}, {1, 7}, {3, 1}, {2, 0},
- {1, 5}, {2, 6}, {2, 7}, {2, 1}, {2, 4},
- {2, 5}, {1, 2}, {2, 3}, {2, 2}, {3, 0},
- {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1},
- {-1, -1},
-};
-
-const int keyboard_factory_scan_pins_used =
- ARRAY_SIZE(keyboard_factory_scan_pins);
-
-static void ppc_interrupt(enum gpio_signal signal)
-{
- switch (signal) {
- case GPIO_USB_C0_PPC_INT_ODL:
- sn5s330_interrupt(0);
- break;
-
- case GPIO_USB_C1_PPC_INT_ODL:
- sn5s330_interrupt(1);
- break;
-
- default:
- break;
- }
-}
-
-static void tcpc_alert_event(enum gpio_signal signal)
-{
- int port = -1;
-
- switch (signal) {
- case GPIO_USB_C0_TCPC_INT_ODL:
- port = 0;
- break;
- case GPIO_USB_C1_TCPC_INT_ODL:
- port = 1;
- break;
- default:
- return;
- }
-
- schedule_deferred_pd_interrupt(port);
-}
-
-static void hdmi_hpd_interrupt(enum gpio_signal signal)
-{
- baseboard_mst_enable_control(MST_HDMI, gpio_get_level(signal));
-}
-
-static void bc12_interrupt(enum gpio_signal signal)
-{
- switch (signal) {
- case GPIO_USB_C0_BC12_INT_ODL:
- task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12);
- break;
-
- case GPIO_USB_C1_BC12_INT_ODL:
- task_set_event(TASK_ID_USB_CHG_P1, USB_CHG_EVENT_BC12);
- break;
-
- default:
- break;
- }
-}
-
-#include "gpio_list.h" /* Must come after other header files. */
-
-/******************************************************************************/
-/* SPI devices */
-const struct spi_device_t spi_devices[] = {
-};
-const unsigned int spi_devices_used = ARRAY_SIZE(spi_devices);
-
-/******************************************************************************/
-/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */
-const struct pwm_t pwm_channels[] = {
- [PWM_CH_KBLIGHT] = { .channel = 3, .flags = 0, .freq = 10000 },
- [PWM_CH_FAN] = {.channel = 5, .flags = PWM_CONFIG_OPEN_DRAIN,
- .freq = 25000},
-};
-BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
-
-/******************************************************************************/
-/* USB-C TPCP Configuration */
-const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = {
- [USB_PD_PORT_TCPC_0] = {
- .bus_type = EC_BUS_TYPE_I2C,
- .i2c_info = {
- .port = I2C_PORT_TCPC0,
- .addr_flags = AN7447_TCPC0_I2C_ADDR_FLAGS,
- },
- .drv = &anx7447_tcpm_drv,
- .flags = TCPC_FLAGS_RESET_ACTIVE_HIGH,
- },
- [USB_PD_PORT_TCPC_1] = {
- .bus_type = EC_BUS_TYPE_I2C,
- .i2c_info = {
- .port = I2C_PORT_TCPC1,
- .addr_flags = PS8751_I2C_ADDR1_FLAGS,
- },
- .drv = &ps8xxx_tcpm_drv,
- .flags = 0,
- },
-};
-
-const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = {
- [USB_PD_PORT_TCPC_0] = {
- .usb_port = USB_PD_PORT_TCPC_0,
- .driver = &anx7447_usb_mux_driver,
- .hpd_update = &anx7447_tcpc_update_hpd_status,
- },
- [USB_PD_PORT_TCPC_1] = {
- .usb_port = USB_PD_PORT_TCPC_1,
- .driver = &tcpci_tcpm_usb_mux_driver,
- .hpd_update = &ps8xxx_tcpc_update_hpd_status,
- }
-};
-
-const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = {
- [USB_PD_PORT_TCPC_0] = {
- .i2c_port = I2C_PORT_PPC0,
- .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
- },
-
- [USB_PD_PORT_TCPC_1] = {
- .i2c_port = I2C_PORT_TCPC1,
- .i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
- },
-};
-
-/******************************************************************************/
-/* Sensors */
-/* Base Sensor mutex */
-static struct mutex g_base_mutex;
-static struct mutex g_lid_mutex;
-
-/* Base accel private data */
-static struct bmi_drv_data_t g_bmi160_data;
-static struct icm_drv_data_t g_icm426xx_data;
-
-/* BMA255 private data */
-static struct accelgyro_saved_data_t g_bma255_data;
-static struct kionix_accel_data g_kx022_data;
-
-/* Matrix to rotate accelrator into standard reference frame */
-static const mat33_fp_t base_standard_ref = {
- { FLOAT_TO_FP(-1), 0, 0},
- { 0, FLOAT_TO_FP(-1), 0},
- { 0, 0, FLOAT_TO_FP(1)}
-};
-
-static const mat33_fp_t lid_standard_ref = {
- { FLOAT_TO_FP(-1), 0, 0},
- { 0, FLOAT_TO_FP(-1), 0},
- { 0, 0, FLOAT_TO_FP(1)}
-};
-
-static const mat33_fp_t base_icm_ref = {
- { 0, FLOAT_TO_FP(1), 0},
- { FLOAT_TO_FP(-1), 0, 0},
- { 0, 0, FLOAT_TO_FP(1)}
-};
-
-struct motion_sensor_t kx022_lid_accel = {
- .name = "Lid Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_KX022,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_LID,
- .drv = &kionix_accel_drv,
- .mutex = &g_lid_mutex,
- .drv_data = &g_kx022_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = KX022_ADDR0_FLAGS,
- .rot_standard_ref = &lid_standard_ref,
- .min_frequency = KX022_ACCEL_MIN_FREQ,
- .max_frequency = KX022_ACCEL_MAX_FREQ,
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- },
-};
-
-struct motion_sensor_t icm426xx_base_accel = {
- .name = "Base Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_ICM426XX,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &icm426xx_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_icm426xx_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS,
- .default_range = 2, /* g, enough for laptop */
- .rot_standard_ref = &base_icm_ref,
- .min_frequency = ICM426XX_ACCEL_MIN_FREQ,
- .max_frequency = ICM426XX_ACCEL_MAX_FREQ,
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- .ec_rate = 100,
- },
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- },
-};
-
-struct motion_sensor_t icm426xx_base_gyro = {
- .name = "Base Gyro",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_ICM426XX,
- .type = MOTIONSENSE_TYPE_GYRO,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &icm426xx_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_icm426xx_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = ICM426XX_ADDR0_FLAGS,
- .default_range = 1000, /* dps */
- .rot_standard_ref = &base_icm_ref,
- .min_frequency = ICM426XX_GYRO_MIN_FREQ,
- .max_frequency = ICM426XX_GYRO_MAX_FREQ,
-};
-
-
-struct motion_sensor_t motion_sensors[] = {
- [LID_ACCEL] = {
- .name = "Lid Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_BMA255,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_LID,
- .drv = &bma2x2_accel_drv,
- .mutex = &g_lid_mutex,
- .drv_data = &g_bma255_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = BMA2x2_I2C_ADDR1_FLAGS,
- .rot_standard_ref = &lid_standard_ref,
- .min_frequency = BMA255_ACCEL_MIN_FREQ,
- .max_frequency = BMA255_ACCEL_MAX_FREQ,
- .default_range = 2, /* g, to support lid angle calculation. */
- .config = {
- /* EC use accel for angle detection */
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- /* Sensor on in S3 */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- },
- },
-
- [BASE_ACCEL] = {
- .name = "Base Accel",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_BMI160,
- .type = MOTIONSENSE_TYPE_ACCEL,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &bmi160_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_bmi160_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
- .rot_standard_ref = &base_standard_ref,
- .min_frequency = BMI_ACCEL_MIN_FREQ,
- .max_frequency = BMI_ACCEL_MAX_FREQ,
- .default_range = 4, /* g, to meet CDD 7.3.1/C-1-4 reqs */
- .config = {
- [SENSOR_CONFIG_EC_S0] = {
- .odr = 10000 | ROUND_UP_FLAG,
- .ec_rate = 100,
- },
- /* Sensor on in S3 */
- [SENSOR_CONFIG_EC_S3] = {
- .odr = 10000 | ROUND_UP_FLAG,
- },
- },
- },
-
- [BASE_GYRO] = {
- .name = "Base Gyro",
- .active_mask = SENSOR_ACTIVE_S0_S3,
- .chip = MOTIONSENSE_CHIP_BMI160,
- .type = MOTIONSENSE_TYPE_GYRO,
- .location = MOTIONSENSE_LOC_BASE,
- .drv = &bmi160_drv,
- .mutex = &g_base_mutex,
- .drv_data = &g_bmi160_data,
- .port = I2C_PORT_ACCEL,
- .i2c_spi_addr_flags = BMI160_ADDR0_FLAGS,
- .default_range = 1000, /* dps */
- .rot_standard_ref = &base_standard_ref,
- .min_frequency = BMI_GYRO_MIN_FREQ,
- .max_frequency = BMI_GYRO_MAX_FREQ,
- },
-};
-unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
-
-/******************************************************************************/
-/* Physical fans. These are logically separate from pwm_channels. */
-
-const struct fan_conf fan_conf_0 = {
- .flags = FAN_USE_RPM_MODE,
- .ch = MFT_CH_0, /* Use MFT id to control fan */
- .pgood_gpio = -1,
- .enable_gpio = GPIO_EN_PP5000_FAN,
-};
-
-/* Default */
-const struct fan_rpm fan_rpm_0 = {
- .rpm_min = 3200,
- .rpm_start = 3200,
- .rpm_max = 6500,
-};
-
-const struct fan_t fans[FAN_CH_COUNT] = {
- [FAN_CH_0] = { .conf = &fan_conf_0, .rpm = &fan_rpm_0, },
-};
-
-/******************************************************************************/
-/* MFT channels. These are logically separate from pwm_channels. */
-const struct mft_t mft_channels[] = {
- [MFT_CH_0] = {NPCX_MFT_MODULE_1, TCKC_LFCLK, PWM_CH_FAN},
-};
-BUILD_ASSERT(ARRAY_SIZE(mft_channels) == MFT_CH_COUNT);
-
-/* ADC channels */
-const struct adc_t adc_channels[] = {
- [ADC_TEMP_SENSOR_1] = {
- "TEMP_AMB", NPCX_ADC_CH0, ADC_MAX_VOLT, ADC_READ_MAX+1, 0},
- [ADC_TEMP_SENSOR_2] = {
- "TEMP_CHARGER", NPCX_ADC_CH1, ADC_MAX_VOLT, ADC_READ_MAX+1, 0},
- [ADC_TEMP_SENSOR_3] = {
- "TEMP_WIFI", NPCX_ADC_CH3, ADC_MAX_VOLT, ADC_READ_MAX+1, 0},
-};
-BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
-
-const struct temp_sensor_t temp_sensors[] = {
- [TEMP_SENSOR_1] = {.name = "Temp1",
- .type = TEMP_SENSOR_TYPE_BOARD,
- .read = get_temp_3v3_30k9_47k_4050b,
- .idx = ADC_TEMP_SENSOR_1},
- [TEMP_SENSOR_2] = {.name = "Temp2",
- .type = TEMP_SENSOR_TYPE_BOARD,
- .read = get_temp_3v3_30k9_47k_4050b,
- .idx = ADC_TEMP_SENSOR_2},
- [TEMP_SENSOR_3] = {.name = "Temp3",
- .type = TEMP_SENSOR_TYPE_BOARD,
- .read = get_temp_3v3_30k9_47k_4050b,
- .idx = ADC_TEMP_SENSOR_3},
-};
-BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT);
-
-
-/* Hatch Temperature sensors */
-/*
- * TODO(b/124316213): These setting need to be reviewed and set appropriately
- * for Hatch. They matter when the EC is controlling the fan as opposed to DPTF
- * control.
- */
-const static struct ec_thermal_config thermal_a = {
- .temp_host = {
- [EC_TEMP_THRESH_WARN] = 0,
- [EC_TEMP_THRESH_HIGH] = C_TO_K(65),
- [EC_TEMP_THRESH_HALT] = C_TO_K(75),
- },
- .temp_host_release = {
- [EC_TEMP_THRESH_WARN] = 0,
- [EC_TEMP_THRESH_HIGH] = C_TO_K(55),
- [EC_TEMP_THRESH_HALT] = 0,
- },
- .temp_fan_off = C_TO_K(25),
- .temp_fan_max = C_TO_K(55),
-};
-
-struct ec_thermal_config thermal_params[TEMP_SENSOR_COUNT];
-
-static void setup_fans(void)
-{
- thermal_params[TEMP_SENSOR_1] = thermal_a;
- thermal_params[TEMP_SENSOR_2] = thermal_a;
-}
-
-/* Sets the gpio flags correct taking into account warm resets */
-static void reset_gpio_flags(enum gpio_signal signal, int flags)
-{
- /*
- * If the system was already on, we cannot set the value otherwise we
- * may change the value from the previous image which could cause a
- * brownout.
- */
- if (system_is_reboot_warm() || system_jumped_late())
- flags &= ~(GPIO_LOW | GPIO_HIGH);
-
- gpio_set_flags(signal, flags);
-}
-
-/* Runtime GPIO defaults */
-enum gpio_signal gpio_en_pp5000_a = GPIO_EN_PP5000_A_V1;
-
-static void board_gpio_set_pp5000(void)
-{
- uint32_t board_id = 0;
-
- /* Errors will count as board_id 0 */
- cbi_get_board_version(&board_id);
-
- if (board_id == 0) {
- reset_gpio_flags(GPIO_EN_PP5000_A_V0, GPIO_OUT_LOW);
- /* Change runtime default for V0 */
- gpio_en_pp5000_a = GPIO_EN_PP5000_A_V0;
- } else if (board_id >= 1) {
- reset_gpio_flags(GPIO_EN_PP5000_A_V1, GPIO_OUT_LOW);
- }
-
-}
-
-bool board_is_convertible(void)
-{
- uint8_t sku_id = get_board_sku();
- /* SKU ID of Kled : 1, 2, 3, 4 */
- return (sku_id >= 1) && (sku_id <= 4);
-}
-
-static void board_update_sensor_config_from_sku(void)
-{
- /*
- * There are two possible sensor configurations. Clamshell device will
- * not have any of the motion sensors populated, while convertible
- * devices have the BMI160 Accel/Gryo lid acceleration sensor.
- * If a new SKU id is used that is not in the threshold, then the
- * number of motion sensors will remain as ARRAY_SIZE(motion_sensors).
- */
- if (board_is_convertible()) {
- motion_sensor_count = ARRAY_SIZE(motion_sensors);
- /* Enable gpio interrupt for base accelgyro sensor */
- gpio_enable_interrupt(GPIO_BASE_SIXAXIS_INT_L);
-
- CPRINTS("Motion Sensor Count = %d", motion_sensor_count);
- } else {
- motion_sensor_count = 0;
- /* Device is clamshell only */
- tablet_disable();
- /* Base accel is not stuffed, don't allow line to float */
- gpio_set_flags(GPIO_BASE_SIXAXIS_INT_L,
- GPIO_INPUT | GPIO_PULL_DOWN);
- }
-}
-
-static void anx7447_set_aux_switch(void)
-{
- const int port = USB_PD_PORT_TCPC_0;
-
- /* Debounce */
- if (gpio_get_level(GPIO_CCD_MODE_ODL))
- return;
-
- /*
- * Expect to set AUX_SWITCH to 0, but 0xc isolates the DP_AUX
- * signal from SBU.
- */
- CPRINTS("C%d: AUX_SW_SEL=0x%x", port, 0xc);
- if (tcpc_write(port, ANX7447_REG_TCPC_AUX_SWITCH, 0xc))
- CPRINTS("C%d: Setting AUX_SW_SEL failed", port);
-}
-DECLARE_DEFERRED(anx7447_set_aux_switch);
-
-void ccd_mode_isr(enum gpio_signal signal)
-{
- /* Wait 2 seconds until all mux setting is done by PD task */
- hook_call_deferred(&anx7447_set_aux_switch_data, 2 * SECOND);
-}
-
-static void board_init(void)
-{
- /* Initialize Fans */
- setup_fans();
- /* Enable HDMI HPD interrupt. */
- gpio_enable_interrupt(GPIO_HDMI_CONN_HPD);
- /* Trigger once to set mux in case CCD cable is already connected. */
- ccd_mode_isr(GPIO_CCD_MODE_ODL);
- gpio_enable_interrupt(GPIO_CCD_MODE_ODL);
- /* Select correct gpio signal for PP5000_A control */
- board_gpio_set_pp5000();
- /* Use sku_id to set motion sensor count */
- board_update_sensor_config_from_sku();
-}
-DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
-
-static void determine_accel_devices(void)
-{
- static uint8_t read_time;
-
- if (chipset_in_state(CHIPSET_STATE_ANY_OFF))
- return;
-
- if (read_time == 0 && board_is_convertible()) {
- /* Read g sensor chip id*/
- i2c_read8(I2C_PORT_ACCEL,
- KX022_ADDR0_FLAGS, KX022_WHOAMI, &lid_device_id);
- /* Read gyro sensor id*/
- i2c_read8(I2C_PORT_ACCEL,
- ICM426XX_ADDR0_FLAGS,
- ICM426XX_REG_WHO_AM_I, &base_device_id);
-
- CPRINTS("Motion Sensor Base id = %d Lid id =%d",
- base_device_id, lid_device_id);
-
- if (lid_device_id == KX022_WHO_AM_I_VAL) {
- motion_sensors[LID_ACCEL] = kx022_lid_accel;
- ccprints("Lid Accel is KX022");
- } else
- ccprints("Lid Accel is BMA255");
-
- if (base_device_id == ICM426XX_CHIP_ICM40608) {
- motion_sensors[BASE_ACCEL] = icm426xx_base_accel;
- motion_sensors[BASE_GYRO] = icm426xx_base_gyro;
- ccprints("BASE Accel is ICM426XX");
- } else
- ccprints("BASE Accel is BMI160");
-
- read_time++;
- }
-}
-DECLARE_HOOK(HOOK_CHIPSET_RESUME, determine_accel_devices, HOOK_PRIO_DEFAULT);
-DECLARE_HOOK(HOOK_INIT, determine_accel_devices, HOOK_PRIO_INIT_ADC + 2);
-
-void motion_interrupt(enum gpio_signal signal)
-{
- switch (base_device_id) {
- case ICM426XX_CHIP_ICM40608:
- icm426xx_interrupt(signal);
- break;
- default:
- bmi160_interrupt(signal);
- break;
- }
-}
-
-void board_overcurrent_event(int port, int is_overcurrented)
-{
- /* Check that port number is valid. */
- if ((port < 0) || (port >= CONFIG_USB_PD_PORT_MAX_COUNT))
- return;
-
- /* Note that the level is inverted because the pin is active low. */
- gpio_set_level(GPIO_USB_C_OC_ODL, !is_overcurrented);
-}
-
-bool board_has_kb_backlight(void)
-{
- uint8_t sku_id = get_board_sku();
- /* SKU ID of Kled with KB backlight: 1, 2, 3, 4 */
- return (sku_id >= 1) && (sku_id <= 4);
-}
-
-__override uint32_t board_override_feature_flags0(uint32_t flags0)
-{
- if (board_has_kb_backlight())
- return flags0;
- else
- return (flags0 & ~EC_FEATURE_MASK_0(EC_FEATURE_PWM_KEYB));
-}
-
-void all_sys_pgood_check_reboot(void)
-{
- hook_call_deferred(&check_reboot_deferred_data, 3000 * MSEC);
-}
-
-__override void board_chipset_forced_shutdown(void)
-{
- hook_call_deferred(&check_reboot_deferred_data, -1);
-}
-DECLARE_HOOK(HOOK_CHIPSET_SHUTDOWN, board_chipset_forced_shutdown, HOOK_PRIO_DEFAULT);
-
-static void check_reboot_deferred(void)
-{
- if (!gpio_get_level(GPIO_PG_EC_ALL_SYS_PWRGD))
- system_reset(SYSTEM_RESET_MANUALLY_TRIGGERED);
-}
diff --git a/board/kindred/board.h b/board/kindred/board.h
deleted file mode 100644
index 79fc7c0642..0000000000
--- a/board/kindred/board.h
+++ /dev/null
@@ -1,188 +0,0 @@
-/* Copyright 2019 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Hatch board configuration */
-
-#ifndef __CROS_EC_BOARD_H
-#define __CROS_EC_BOARD_H
-
-/* Baseboard features */
-#include "baseboard.h"
-
-#define CONFIG_POWER_BUTTON
-#undef CONFIG_POWER_BUTTON_INIT_TIMEOUT
-#define CONFIG_POWER_BUTTON_INIT_TIMEOUT 2
-#define CONFIG_KEYBOARD_PROTOCOL_8042
-#define CONFIG_LED_COMMON
-#define CONFIG_LOW_POWER_IDLE
-
-#define CONFIG_HOSTCMD_ESPI
-
-#undef CONFIG_UART_TX_BUF_SIZE
-#define CONFIG_UART_TX_BUF_SIZE 4096
-
-/* Keyboard features */
-#define CONFIG_PWM
-#define CONFIG_PWM_KBLIGHT
-/* support factory keyboard test */
-#define CONFIG_KEYBOARD_FACTORY_TEST
-
-/* Sensors */
-/* BMI160 Base accel/gyro */
-#define CONFIG_ACCEL_INTERRUPTS
-
-#define CONFIG_ACCELGYRO_BMI160
-#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
- TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-
-#define CONFIG_ACCELGYRO_ICM426XX
-#define CONFIG_ACCELGYRO_ICM426XX_INT_EVENT \
- TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
-
-#define CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT
-/* BMA253 Lid accel */
-#define CONFIG_ACCEL_BMA255
-#define CONFIG_ACCEL_KX022
-#define CONFIG_LID_ANGLE
-#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
-#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
-#define CONFIG_LID_ANGLE_UPDATE
-#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
-
-/* USB Type C and USB PD defines */
-#define CONFIG_USB_PD_COMM_LOCKED
-#define CONFIG_USB_PD_TCPM_ANX7447
-#define CONFIG_USB_PD_TCPM_ANX7447_AUX_PU_PD
-#define CONFIG_USB_PD_TCPM_PS8751
-#define BOARD_TCPC_C0_RESET_HOLD_DELAY ANX74XX_RESET_HOLD_MS
-#define BOARD_TCPC_C0_RESET_POST_DELAY ANX74XX_RESET_HOLD_MS
-#define BOARD_TCPC_C1_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
-#define BOARD_TCPC_C1_RESET_POST_DELAY 0
-#define GPIO_USB_C1_TCPC_RST GPIO_USB_C1_TCPC_RST_ODL
-
-/* USB Type A Features */
-#define CONFIG_USB_PORT_POWER_SMART
-#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT
-#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1
-#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
-#define GPIO_USB1_ILIM_SEL GPIO_EN_USB_A_LOW_PWR_OD
-
-/* BC 1.2 */
-#define CONFIG_BC12_DETECT_PI3USB9201
-
-/* Charger features */
-/*
- * The IDCHG current limit is set in 512 mA steps. The value set here is
- * somewhat specific to the battery pack being currently used. The limit here
- * was set based on the battery's discharge current limit and what was tested to
- * prevent the AP rebooting with low charge level batteries.
- *
- * TODO(b/133447140): Revisit this threshold once peak power consumption tuning
- * for the AP is completed.
- */
-#define CONFIG_CHARGER_BQ25710_IDCHG_LIMIT_MA 8192
-
-/* Volume Button feature */
-#define CONFIG_VOLUME_BUTTONS
-#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
-#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
-
-/* Fan features */
-#define CONFIG_FANS 1
-#undef CONFIG_FAN_INIT_SPEED
-#define CONFIG_FAN_INIT_SPEED 50
-#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_A_RAILS
-#define CONFIG_THERMISTOR
-#define CONFIG_THROTTLE_AP
-#define CONFIG_STEINHART_HART_3V3_30K9_47K_4050B
-
-/* MST */
-/*
- * TDOD (b/124068003): This inherently assumes the MST chip is connected to only
- * one Type C port. This will need to be chagned to support 2 Type C ports
- * connected to the same MST chip.
- */
-#define USB_PD_PORT_TCPC_MST USB_PD_PORT_TCPC_1
-
-/*
- * Macros for GPIO signals used in common code that don't match the
- * schematic names. Signal names in gpio.inc match the schematic and are
- * then redefined here to so it's more clear which signal is being used for
- * which purpose.
- */
-#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L
-#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
-#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
-#define GPIO_AC_PRESENT GPIO_ACOK_OD
-#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_L
-#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK
-#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
-#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L
-#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
-
-#ifndef __ASSEMBLER__
-#include "gpio_signal.h"
-#include "registers.h"
-
-/* GPIO signals updated base on board version. */
-#define GPIO_EN_PP5000_A gpio_en_pp5000_a
-extern enum gpio_signal gpio_en_pp5000_a;
-
-enum adc_channel {
- ADC_TEMP_SENSOR_1, /* ADC0 */
- ADC_TEMP_SENSOR_2, /* ADC1 */
- ADC_TEMP_SENSOR_3, /* ADC3 */
- ADC_CH_COUNT
-};
-
-enum sensor_id {
- LID_ACCEL = 0,
- BASE_ACCEL,
- BASE_GYRO,
- SENSOR_COUNT,
-};
-
-enum pwm_channel {
- PWM_CH_KBLIGHT,
- PWM_CH_FAN,
- PWM_CH_COUNT
-};
-
-enum fan_channel {
- FAN_CH_0 = 0,
- /* Number of FAN channels */
- FAN_CH_COUNT,
-};
-
-enum mft_channel {
- MFT_CH_0 = 0,
- /* Number of MFT channels */
- MFT_CH_COUNT,
-};
-
-enum temp_sensor_id {
- TEMP_SENSOR_1,
- TEMP_SENSOR_2,
- TEMP_SENSOR_3,
- TEMP_SENSOR_COUNT
-};
-
-/* List of possible batteries */
-enum battery_type {
- BATTERY_LGC_AP18C8K,
- BATTERY_MURATA_AP18C4K,
- BATTERY_TYPE_COUNT,
-};
-
-/* Sensors without hardware FIFO are in forced mode */
-#define CONFIG_ACCEL_FORCE_MODE_MASK (1 << LID_ACCEL)
-
-void motion_interrupt(enum gpio_signal signal);
-
-void ccd_mode_isr(enum gpio_signal signal);
-
-#endif /* !__ASSEMBLER__ */
-
-#endif /* __CROS_EC_BOARD_H */
diff --git a/board/kindred/build.mk b/board/kindred/build.mk
deleted file mode 100644
index 733912454f..0000000000
--- a/board/kindred/build.mk
+++ /dev/null
@@ -1,15 +0,0 @@
-# -*- makefile -*-
-# Copyright 2019 The Chromium OS Authors. All rights reserved.
-# Use of this source code is governed by a BSD-style license that can be
-# found in the LICENSE file.
-#
-# Board specific files build
-#
-
-CHIP:=npcx
-CHIP_FAMILY:=npcx7
-CHIP_VARIANT:=npcx7m6fc
-BASEBOARD:=hatch
-
-board-y=board.o led.o
-board-$(CONFIG_BATTERY_SMART)+=battery.o
diff --git a/board/kindred/ec.tasklist b/board/kindred/ec.tasklist
deleted file mode 100644
index 4a1024a091..0000000000
--- a/board/kindred/ec.tasklist
+++ /dev/null
@@ -1,26 +0,0 @@
-/* Copyright 2019 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/*
- * See CONFIG_TASK_LIST in config.h for details.
- */
-
-#define CONFIG_TASK_LIST \
- TASK_ALWAYS(HOOKS, hook_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 1, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(CHARGER, charger_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_NOTEST(CHIPSET, chipset_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \
- TASK_ALWAYS(HOSTCMD, host_command_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(POWERBTN, power_button_task, NULL, LARGER_TASK_STACK_SIZE) \
- TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_C0, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_C1, pd_task, NULL, VENTI_TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_INT_C0, pd_interrupt_handler_task, 0, TASK_STACK_SIZE) \
- TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, TASK_STACK_SIZE)
-
diff --git a/board/kindred/gpio.inc b/board/kindred/gpio.inc
deleted file mode 100644
index 2adb08f564..0000000000
--- a/board/kindred/gpio.inc
+++ /dev/null
@@ -1,146 +0,0 @@
-/* -*- mode:c -*-
- *
- * Copyright 2019 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Declare symbolic names for all the GPIOs that we care about.
- * Note: Those with interrupt handlers must be declared first. */
-
-/* Wake Source interrupts */
-GPIO_INT(LID_OPEN, PIN(D, 2), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, lid_interrupt)
-GPIO_INT(WP_L, PIN(A, 1), GPIO_INT_BOTH, switch_interrupt) /* EC_WP_ODL */
-GPIO_INT(POWER_BUTTON_L, PIN(0, 1), GPIO_INT_BOTH, power_button_interrupt) /* MECH_PWR_BTN_ODL */
-GPIO_INT(ACOK_OD, PIN(0, 0), GPIO_INT_BOTH | GPIO_HIB_WAKE_HIGH, extpower_interrupt)
-
-/* Power sequencing interrupts */
-GPIO_INT(SLP_S0_L, PIN(D, 5), GPIO_INT_BOTH, power_signal_interrupt)
-#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S3
-GPIO_INT(SLP_S3_L, PIN(A, 5), GPIO_INT_BOTH, power_signal_interrupt)
-#endif
-#ifndef CONFIG_HOSTCMD_ESPI_VW_SLP_S4
-GPIO_INT(SLP_S4_L, PIN(D, 4), GPIO_INT_BOTH, power_signal_interrupt)
-#endif
-GPIO_INT(PG_EC_RSMRST_L, PIN(E, 2), GPIO_INT_BOTH, intel_x86_rsmrst_signal_interrupt)
-GPIO_INT(PG_EC_ALL_SYS_PWRGD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(PP5000_A_PG_OD, PIN(D, 7), GPIO_INT_BOTH, power_signal_interrupt)
-
-/* Sensor Interrupts */
-GPIO_INT(BASE_SIXAXIS_INT_L, PIN(5, 6), GPIO_INT_FALLING, motion_interrupt)
-
-/* USB-C interrupts */
-GPIO_INT(USB_C0_PPC_INT_ODL, PIN(E, 0), GPIO_INT_FALLING, ppc_interrupt)
-GPIO_INT(USB_C1_PPC_INT_ODL, PIN(A, 2), GPIO_INT_FALLING, ppc_interrupt)
-GPIO_INT(USB_C0_TCPC_INT_ODL, PIN(6, 2), GPIO_INT_FALLING, tcpc_alert_event)
-GPIO_INT(USB_C1_TCPC_INT_ODL, PIN(F, 5), GPIO_INT_FALLING, tcpc_alert_event)
-GPIO_INT(USB_C0_BC12_INT_ODL, PIN(9, 5), GPIO_INT_FALLING, bc12_interrupt)
-GPIO_INT(USB_C1_BC12_INT_ODL, PIN(E, 4), GPIO_INT_FALLING, bc12_interrupt)
-
-/* CCD mode line*/
-GPIO_INT(CCD_MODE_ODL, PIN(E, 5), GPIO_INT_FALLING, ccd_mode_isr)
-
-GPIO_INT(HDMI_CONN_HPD, PIN(7, 2), GPIO_INT_BOTH, hdmi_hpd_interrupt)
-
-/* Volume button interrupts */
-GPIO_INT(EC_VOLDN_BTN_ODL, PIN(9, 3), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
-GPIO_INT(EC_VOLUP_BTN_ODL, PIN(7, 5), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt)
-
-GPIO(SYS_RESET_L, PIN(C, 5), GPIO_ODR_HIGH) /* SYS_RST_ODL */
-GPIO(ENTERING_RW, PIN(E, 3), GPIO_OUT_LOW) /* EC_ENTERING_RW */
-GPIO(PCH_WAKE_L, PIN(7, 4), GPIO_ODR_HIGH) /* EC_PCH_WAKE_ODL */
-GPIO(PCH_PWRBTN_L, PIN(C, 1), GPIO_ODR_HIGH) /* EC_PCH_PWR_BTN_ODL */
-
-/* Power Sequencing Signals */
-GPIO(EN_PP5000_A_V1, PIN(A, 4), GPIO_DEFAULT)
-GPIO(EN_PP5000_A_V0, PIN(7, 3), GPIO_DEFAULT)
-GPIO(EN_A_RAILS, PIN(A, 3), GPIO_OUT_LOW)
-GPIO(EC_PCH_RSMRST_L, PIN(A, 6), GPIO_OUT_LOW)
-GPIO(EC_PROCHOT_ODL, PIN(6, 3), GPIO_ODR_HIGH)
-GPIO(EC_PROCHOT_IN_OD, PIN(3, 4), GPIO_INPUT)
-GPIO(EC_PCH_SYS_PWROK, PIN(3, 7), GPIO_OUT_LOW)
-GPIO(CPU_C10_GATE_L, PIN(6, 7), GPIO_INPUT)
-
-/* MKBP event synchronization */
-GPIO(EC_INT_L, PIN(7, 0), GPIO_ODR_HIGH)
-
-/*
- * GPIO_INT_BOTH is required for PSL wake from hibernate, but we don't need an
- * interrupt handler because it is automatically handled by the PSL.
- *
- * We need to lock the setting so this gpio can't be reconfigured to overdrive
- * the real reset signal. (This is the PSL input pin not the real reset pin).
- */
-GPIO(EC_RST_ODL, PIN(0, 2), GPIO_INT_BOTH |
- GPIO_HIB_WAKE_HIGH |
- GPIO_LOCKED)
-
-/* USB and USBC Signals */
-GPIO(USB_C_OC_ODL, PIN(B, 1), GPIO_ODR_HIGH)
-GPIO(USB_C0_TCPC_RST, PIN(9, 7), GPIO_OUT_LOW)
-GPIO(USB_C1_TCPC_RST_ODL, PIN(3, 2), GPIO_ODR_HIGH)
-GPIO(EN_USB_A_5V, PIN(3, 5), GPIO_OUT_LOW)
-GPIO(EN_USB_A_LOW_PWR_OD, PIN(9, 4), GPIO_OUT_LOW)
-
-/* Misc Signals */
-GPIO(EC_BATT_PRES_ODL, PIN(E, 1), GPIO_INPUT)
-GPIO(LED_1_L, PIN(C, 4), GPIO_OUT_HIGH) /* Blue (kindred) */
-GPIO(LED_2_L, PIN(C, 3), GPIO_OUT_HIGH) /* Yellow (kindred) */
-GPIO(LED_3_L, PIN(C, 2), GPIO_OUT_HIGH)
-GPIO(LED_4_L, PIN(6, 0), GPIO_OUT_HIGH)
-GPIO(EC_KB_BL_EN, PIN(8, 6), GPIO_OUT_LOW) /* Keyboard backlight */
-GPIO(EDP_BKLTEN_OD, PIN(D, 3), GPIO_ODR_HIGH) /* Display backlight */
-GPIO(EN_PP5000_FAN, PIN(6, 1), GPIO_OUT_LOW)
-GPIO(EN_MST, PIN(9, 6), GPIO_OUT_LOW)
-
-
-/* I2C pins - Alternate function below configures I2C module on these pins */
-GPIO(I2C0_SCL, PIN(B, 5), GPIO_INPUT |
- GPIO_SEL_1P8V) /* EC_I2C_SENSOR_1V8_SCL */
-GPIO(I2C0_SDA, PIN(B, 4), GPIO_INPUT |
- GPIO_SEL_1P8V) /* EC_I2C_SENSOR_1V8_SDA */
-GPIO(I2C1_SCL, PIN(9, 0), GPIO_INPUT) /* EC_I2C_USB_C0_PD_SCL */
-GPIO(I2C1_SDA, PIN(8, 7), GPIO_INPUT) /* EC_I2C_USB_C0_PD_SDA */
-GPIO(I2C2_SCL, PIN(9, 2), GPIO_INPUT) /* EC_I2C_USB_C1_PD_SCL */
-GPIO(I2C2_SDA, PIN(9, 1), GPIO_INPUT) /* EC_I2C_USB_C1_PD_SDA */
-GPIO(I2C3_SCL, PIN(D, 1), GPIO_INPUT) /* EC_I2C_USB_C0_TCPC_SDA */
-GPIO(I2C3_SDA, PIN(D, 0), GPIO_INPUT) /* EC_I2C_USB_C0_TCPC_SCL */
-GPIO(I2C5_SCL, PIN(3, 3), GPIO_INPUT) /* EC_I2C_POWER_SCL */
-GPIO(I2C5_SDA, PIN(3, 6), GPIO_INPUT) /* EC_I2C_POWER_SDA */
-GPIO(I2C7_SCL, PIN(B, 3), GPIO_INPUT) /* EC_I2C_EEPROM_SCL */
-GPIO(I2C7_SDA, PIN(B, 2), GPIO_INPUT) /* EC_I2C_EEPROM_SDA */
-
-/* Keyboard pins */
-#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP)
-GPIO(KBD_KSO2, PIN(1, 7), GPIO_OUT_LOW) /* KSO_02 inverted */
-ALTERNATE(PIN_MASK(3, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_00-01 */
-ALTERNATE(PIN_MASK(2, 0xFC), 0, MODULE_KEYBOARD_SCAN, GPIO_KB_INPUT) /* KSI_02-07 */
-ALTERNATE(PIN_MASK(2, 0x03), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_00-01 */
-ALTERNATE(PIN_MASK(1, 0x7F), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_03-09 */
-ALTERNATE(PIN_MASK(0, 0xF0), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_10-13 */
-ALTERNATE(PIN_MASK(8, 0x04), 0, MODULE_KEYBOARD_SCAN, GPIO_ODR_HIGH) /* KSO_14 */
-
-/* Alternate functions GPIO definitions */
-ALTERNATE(PIN_MASK(B, 0x30), 0, MODULE_I2C, (GPIO_INPUT | GPIO_SEL_1P8V)) /* I2C0 1.8V */
-ALTERNATE(PIN_MASK(9, 0x07), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */
-ALTERNATE(PIN_MASK(8, 0x80), 0, MODULE_I2C, 0) /* I2C1 SDA */
-ALTERNATE(PIN_MASK(D, 0x03), 0, MODULE_I2C, 0) /* I2C3 */
-ALTERNATE(PIN_MASK(3, 0x48), 0, MODULE_I2C, 0) /* I2C5 */
-ALTERNATE(PIN_MASK(B, 0x0C), 0, MODULE_I2C, 0) /* I2C7 */
-
-/* UART */
-ALTERNATE(PIN_MASK(6, 0x30), 0, MODULE_UART, 0) /* UART from EC to Servo */
-
-/* PWM */
-ALTERNATE(PIN_MASK(8, 0x01), 0, MODULE_PWM, 0) /* PWM3 - Keyboard backlight */
-ALTERNATE(PIN_MASK(B, 0x80), 0, MODULE_PWM, 0) /* PWM5 - FAN */
-ALTERNATE(PIN_MASK(4, 0x01), 0, MODULE_PWM, 0) /* TA1 - Fan Tachometer */
-
-/* ADC */
-ALTERNATE(PIN_MASK(4, 0x30), 0, MODULE_ADC, 0) /* ADC0-1 */
-
-/* Power Switch Logic (PSL) inputs */
-ALTERNATE(PIN_MASK(D, 0x04), 0, MODULE_PMU, 0) /* GPIOD2 = LID_OPEN */
-ALTERNATE(PIN_MASK(0, 0x07), 0, MODULE_PMU, 0) /* GPIO00 = ACOK_OD,
- GPIO01 = MECH_PWR_BTN_ODL
- GPIO02 = EC_RST_ODL */
diff --git a/board/kindred/led.c b/board/kindred/led.c
deleted file mode 100644
index 9eb195d0b6..0000000000
--- a/board/kindred/led.c
+++ /dev/null
@@ -1,81 +0,0 @@
-/* Copyright 2018 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Power and battery LED control for Hatch
- */
-
-#include "ec_commands.h"
-#include "gpio.h"
-#include "led_common.h"
-#include "led_onoff_states.h"
-#include "chipset.h"
-
-#define LED_ON_LVL 0
-#define LED_OFF_LVL 1
-
-__override const int led_charge_lvl_1 = 5;
-
-__override const int led_charge_lvl_2 = 95;
-
-__override struct led_descriptor
- led_bat_state_table[LED_NUM_STATES][LED_NUM_PHASES] = {
- [STATE_CHARGING_LVL_1] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} },
- [STATE_CHARGING_LVL_2] = {{EC_LED_COLOR_AMBER, LED_INDEFINITE} },
- [STATE_CHARGING_FULL_CHARGE] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} },
- [STATE_DISCHARGE_S0] = {{EC_LED_COLOR_BLUE, LED_INDEFINITE} },
- [STATE_DISCHARGE_S3] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC},
- {LED_OFF, 3 * LED_ONE_SEC} },
- [STATE_DISCHARGE_S5] = {{LED_OFF, LED_INDEFINITE} },
- [STATE_BATTERY_ERROR] = {{EC_LED_COLOR_AMBER, 1 * LED_ONE_SEC},
- {LED_OFF, 1 * LED_ONE_SEC} },
- [STATE_FACTORY_TEST] = {{EC_LED_COLOR_BLUE, 2 * LED_ONE_SEC},
- {EC_LED_COLOR_AMBER, 2 * LED_ONE_SEC} },
-};
-
-const enum ec_led_id supported_led_ids[] = {
- EC_LED_ID_BATTERY_LED
-};
-
-const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids);
-
-__override void led_set_color_battery(enum ec_led_colors color)
-{
- switch (color) {
- case EC_LED_COLOR_AMBER:
- gpio_set_level(GPIO_LED_2_L, LED_ON_LVL);
- gpio_set_level(GPIO_LED_1_L, LED_OFF_LVL);
- break;
- case EC_LED_COLOR_BLUE:
- gpio_set_level(GPIO_LED_1_L, LED_ON_LVL);
- gpio_set_level(GPIO_LED_2_L, LED_OFF_LVL);
- break;
- default: /* LED_OFF and other unsupported colors */
- gpio_set_level(GPIO_LED_1_L, LED_OFF_LVL);
- gpio_set_level(GPIO_LED_2_L, LED_OFF_LVL);
- break;
- }
-}
-
-void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range)
-{
- if (led_id == EC_LED_ID_BATTERY_LED) {
- brightness_range[EC_LED_COLOR_AMBER] = 1;
- brightness_range[EC_LED_COLOR_BLUE] = 1;
- }
-}
-
-int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness)
-{
- if (led_id == EC_LED_ID_BATTERY_LED) {
- if (brightness[EC_LED_COLOR_AMBER] != 0)
- led_set_color_battery(EC_LED_COLOR_AMBER);
- else if (brightness[EC_LED_COLOR_BLUE] != 0)
- led_set_color_battery(EC_LED_COLOR_BLUE);
- else
- led_set_color_battery(LED_OFF);
- }
-
- return EC_SUCCESS;
-}
-
diff --git a/board/kindred/vif_override.xml b/board/kindred/vif_override.xml
deleted file mode 100644
index 32736caf64..0000000000
--- a/board/kindred/vif_override.xml
+++ /dev/null
@@ -1,3 +0,0 @@
-<!-- Add VIF field overrides here. See genvif.c and the Vendor Info File
- Definition from the USB-IF.
--->
View Lorry Controller Status