wheelie: Remove it

Wheelie is no more, therefore it's time to remove its files. :c

BUG=None
BRANCH=None
TEST=`make -j buildall`

Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I89f52fb5e44ab49cc653a2cac23c8e444f05cb43
Reviewed-on: https://chromium-review.googlesource.com/c/chromiumos/platform/ec/+/2299847
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Commit-Queue: Diana Z <dzigterman@chromium.org>
Auto-Submit: Aseda Aboagye <aaboagye@chromium.org>

8 files changed, 0 insertions, 1314 deletions

diff --git a/board/wheelie/battery.c b/board/wheelie/battery.c
deleted file mode 100644
index c9770124cd..0000000000
--- a/board/wheelie/battery.c
+++ /dev/null
@@ -1,327 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- *
- * Battery pack vendor provided charging profile
- */
-
-#include "battery_fuel_gauge.h"
-#include "charge_state.h"
-#include "common.h"
-
-/*
- * Battery info for all wheelie battery types. Note that the fields
- * start_charging_min/max and charging_min/max are not used for the charger.
- * The effective temperature limits are given by discharging_min/max_c.
- *
- * Fuel Gauge (FG) parameters which are used for determining if the battery
- * is connected, the appropriate ship mode (battery cutoff) command, and the
- * charge/discharge FETs status.
- *
- * Ship mode (battery cutoff) requires 2 writes to the appropriate smart battery
- * register. For some batteries, the charge/discharge FET bits are set when
- * charging/discharging is active, in other types, these bits set mean that
- * charging/discharging is disabled. Therefore, in addition to the mask for
- * these bits, a disconnect value must be specified. Note that for TI fuel
- * gauge, the charge/discharge FET status is found in Operation Status (0x54),
- * but a read of Manufacturer Access (0x00) will return the lower 16 bits of
- * Operation status which contains the FET status bits.
- *
- * The assumption for battery types supported is that the charge/discharge FET
- * status can be read with a sb_read() command and therefore, only the register
- * address, mask, and disconnect value need to be provided.
- */
-const struct board_batt_params board_battery_info[] = {
-	/* LGC AC15A8J Battery Information */
-	[BATTERY_LGC15] = {
-		.fuel_gauge = {
-			.manuf_name = "LGC",
-			.device_name = "AC15A8J",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.mfgacc_support = 1,
-				.reg_addr = 0x0,
-				.reg_mask = 0x0002,
-				.disconnect_val = 0x0,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= 13200,
-			.voltage_normal		= 11520, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= 0,
-			.discharging_max_c	= 60,
-		},
-	},
-
-	/* Panasonic AP1505L Battery Information */
-	[BATTERY_PANASONIC_AP15O5L] = {
-		.fuel_gauge = {
-			.manuf_name = "PANASONIC",
-			.device_name = "AP15O5L",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x0,
-				.reg_mask = 0x4000,
-				.disconnect_val = 0x0,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= 13200,
-			.voltage_normal		= 11550, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= 0,
-			.discharging_max_c	= 60,
-		},
-	},
-
-	/* SANYO AC15A3J Battery Information */
-	[BATTERY_SANYO] = {
-		.fuel_gauge = {
-			.manuf_name = "SANYO",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x0,
-				.reg_mask = 0x4000,
-				.disconnect_val = 0x0,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= TARGET_WITH_MARGIN(13200, 5),
-			.voltage_normal		= 11550, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= 0,
-			.discharging_max_c	= 60,
-		},
-	},
-
-	/* Sony Ap13J4K Battery Information */
-	[BATTERY_SONY] = {
-		.fuel_gauge = {
-			.manuf_name = "SONYCorp",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x0,
-				.reg_mask = 0x8000,
-				.disconnect_val = 0x8000,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= TARGET_WITH_MARGIN(13200, 5),
-			.voltage_normal		= 11400, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= 0,
-			.discharging_max_c	= 60,
-		},
-	},
-
-	/* Simplo AP13J7K Battery Information */
-	[BATTERY_SMP_AP13J7K] = {
-		.fuel_gauge = {
-			.manuf_name = "SIMPLO",
-			.device_name = "AP13J7K",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.mfgacc_support = 1,
-				.reg_addr = 0x0,
-				.reg_mask = 0x0002,
-				.disconnect_val = 0x0000,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= 13050,
-			.voltage_normal		= 11400, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 45,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= 0,
-			.discharging_max_c	= 60,
-		},
-	},
-
-	/* Panasonic AC15A3J Battery Information */
-	[BATTERY_PANASONIC_AC15A3J] = {
-		.fuel_gauge = {
-			.manuf_name = "PANASONIC",
-			.device_name = "AC15A3J",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x0,
-				.reg_mask = 0x4000,
-				.disconnect_val = 0x0,
-			}
-		},
-		.batt_info = {
-			.voltage_max		= 13200,
-			.voltage_normal		= 11550, /* mV */
-			.voltage_min		= 9000, /* mV */
-			.precharge_current	= 256,	/* mA */
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= -20,
-			.discharging_max_c	= 75,
-		},
-	},
-
-	/* LGC AP18C8K Battery Information */
-	[BATTERY_LGC_AP18C8K] = {
-		.fuel_gauge = {
-			.manuf_name = "LGC KT0030G020",
-			.device_name = "AP18C8K",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x43,
-				.reg_mask = 0x0001,
-				.disconnect_val = 0x0,
-			},
-		},
-		.batt_info = {
-			.voltage_max		= 13050,
-			.voltage_normal		= 11250,
-			.voltage_min		= 9000,
-			.precharge_current	= 256,
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= -20,
-			.discharging_max_c	= 75,
-		},
-	},
-
-	/* Murata AP18C4K Battery Information */
-	[BATTERY_MURATA_AP18C4K] = {
-		.fuel_gauge = {
-			.manuf_name = "Murata KT00304012",
-			.device_name = "AP18C4K",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x0,
-				.reg_mask = 0x2000,
-				.disconnect_val = 0x2000,
-			},
-		},
-		.batt_info = {
-			.voltage_max		= 13200,
-			.voltage_normal		= 11400,
-			.voltage_min		= 9000,
-			.precharge_current	= 256,
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= -20,
-			.discharging_max_c	= 75,
-		},
-	},
-
-	/* LGC AP19A8K Battery Information */
-	[BATTERY_LGC_AP19A8K] = {
-		.fuel_gauge = {
-			.manuf_name = "LGC KTxxxxGxxx",
-			.device_name = "AP19A8K",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x43,
-				.reg_mask = 0x0001,
-				.disconnect_val = 0x0,
-			},
-		},
-		.batt_info = {
-			.voltage_max		= 13200,
-			.voltage_normal		= 11550,
-			.voltage_min		= 9000,
-			.precharge_current	= 256,
-			.start_charging_min_c	= 0,
-			.start_charging_max_c	= 50,
-			.charging_min_c		= 0,
-			.charging_max_c		= 60,
-			.discharging_min_c	= -20,
-			.discharging_max_c	= 75,
-		},
-	},
-
-	/* LGC KT0030G023 Battery Information */
-	[BATTERY_LGC_G023] = {
-		.fuel_gauge = {
-			.manuf_name = "LGC KT0030G023",
-			.device_name = "AP19A8K",
-			.ship_mode = {
-				.reg_addr = 0x3A,
-				.reg_data = { 0xC574, 0xC574 },
-			},
-			.fet = {
-				.reg_addr = 0x43,
-				.reg_mask = 0x0001,
-				.disconnect_val = 0x0,
-			},
-		},
-		.batt_info = {
-			.voltage_max            = 13200,
-			.voltage_normal         = 11550,
-			.voltage_min            = 9000,
-			.precharge_current      = 256,
-			.start_charging_min_c   = 0,
-			.start_charging_max_c   = 50,
-			.charging_min_c         = 0,
-			.charging_max_c         = 60,
-			.discharging_min_c      = -20,
-			.discharging_max_c      = 75,
-		},
-	},
-};
-BUILD_ASSERT(ARRAY_SIZE(board_battery_info) == BATTERY_TYPE_COUNT);
-
-const enum battery_type DEFAULT_BATTERY_TYPE = BATTERY_PANASONIC_AC15A3J;
diff --git a/board/wheelie/board.c b/board/wheelie/board.c
deleted file mode 100644
index 22f6bca2f0..0000000000
--- a/board/wheelie/board.c
+++ /dev/null
@@ -1,500 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Wheelie board-specific configuration */
-
-#include "adc_chip.h"
-#include "button.h"
-#include "charge_manager.h"
-#include "charge_state_v2.h"
-#include "charger.h"
-#include "driver/accel_lis2dh.h"
-#include "driver/accelgyro_lsm6dsm.h"
-#include "driver/bc12/pi3usb9201.h"
-#include "driver/charger/sm5803.h"
-#include "driver/sync.h"
-#include "driver/retimer/tusb544.h"
-#include "driver/temp_sensor/thermistor.h"
-#include "driver/tcpm/anx7447.h"
-#include "driver/tcpm/it83xx_pd.h"
-#include "driver/usb_mux/it5205.h"
-#include "gpio.h"
-#include "hooks.h"
-#include "intc.h"
-#include "keyboard_scan.h"
-#include "lid_switch.h"
-#include "power.h"
-#include "power_button.h"
-#include "pwm.h"
-#include "pwm_chip.h"
-#include "switch.h"
-#include "tablet_mode.h"
-#include "task.h"
-#include "tcpci.h"
-#include "temp_sensor.h"
-#include "uart.h"
-#include "usb_charge.h"
-#include "usb_mux.h"
-#include "usb_pd.h"
-#include "usb_pd_tcpm.h"
-
-#define CPRINTUSB(format, args...) cprints(CC_USBCHARGE, format, ## args)
-
-/* C0 interrupt line shared by BC 1.2 and charger */
-static void usb_c0_interrupt(enum gpio_signal s)
-{
-	task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12, 0);
-	sm5803_interrupt(0);
-}
-
-/* C1 interrupt line shared by BC 1.2, TCPC, and charger */
-static void usb_c1_interrupt(enum gpio_signal s)
-{
-	schedule_deferred_pd_interrupt(1);
-	task_set_event(TASK_ID_USB_CHG_P1, USB_CHG_EVENT_BC12, 0);
-	sm5803_interrupt(1);
-}
-
-static void c0_ccsbu_ovp_interrupt(enum gpio_signal s)
-{
-	cprints(CC_USBPD, "C0: CC OVP, SBU OVP, or thermal event");
-	pd_handle_cc_overvoltage(0);
-}
-
-/* Must come after other header files and interrupt handler declarations */
-#include "gpio_list.h"
-
-/* ADC channels */
-const struct adc_t adc_channels[] = {
-	[ADC_VSNS_PP3300_A] = {
-		.name = "PP3300_A_PGOOD",
-		.factor_mul = ADC_MAX_MVOLT,
-		.factor_div = ADC_READ_MAX + 1,
-		.shift = 0,
-		.channel = CHIP_ADC_CH0
-	},
-	[ADC_TEMP_SENSOR_1] = {
-		.name = "TEMP_SENSOR1",
-		.factor_mul = ADC_MAX_MVOLT,
-		.factor_div = ADC_READ_MAX + 1,
-		.shift = 0,
-		.channel = CHIP_ADC_CH2
-	},
-	[ADC_TEMP_SENSOR_2] = {
-		.name = "TEMP_SENSOR2",
-		.factor_mul = ADC_MAX_MVOLT,
-		.factor_div = ADC_READ_MAX + 1,
-		.shift = 0,
-		.channel = CHIP_ADC_CH3
-	},
-	[ADC_SUB_ANALOG] = {
-		.name = "SUB_ANALOG",
-		.factor_mul = ADC_MAX_MVOLT,
-		.factor_div = ADC_READ_MAX + 1,
-		.shift = 0,
-		.channel = CHIP_ADC_CH13
-	},
-};
-BUILD_ASSERT(ARRAY_SIZE(adc_channels) == ADC_CH_COUNT);
-
-/* BC 1.2 chips */
-const struct pi3usb9201_config_t pi3usb9201_bc12_chips[] = {
-	{
-		.i2c_port = I2C_PORT_USB_C0,
-		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
-	},
-	{
-		.i2c_port = I2C_PORT_SUB_USB_C1,
-		.i2c_addr_flags = PI3USB9201_I2C_ADDR_3_FLAGS,
-	},
-};
-
-/* Charger chips */
-const struct charger_config_t chg_chips[] = {
-	[CHARGER_PRIMARY] = {
-		.i2c_port = I2C_PORT_USB_C0,
-		.i2c_addr_flags = SM5803_ADDR_CHARGER_FLAGS,
-		.drv = &sm5803_drv,
-	},
-	[CHARGER_SECONDARY] = {
-		.i2c_port = I2C_PORT_SUB_USB_C1,
-		.i2c_addr_flags = SM5803_ADDR_CHARGER_FLAGS,
-		.drv = &sm5803_drv,
-	},
-};
-
-/* TCPCs */
-const struct tcpc_config_t tcpc_config[CONFIG_USB_PD_PORT_MAX_COUNT] = {
-	{
-		.bus_type = EC_BUS_TYPE_EMBEDDED,
-		.drv = &it83xx_tcpm_drv,
-	},
-	{
-		.bus_type = EC_BUS_TYPE_I2C,
-		.i2c_info = {
-			.port = I2C_PORT_SUB_USB_C1,
-			.addr_flags = AN7447_TCPC0_I2C_ADDR_FLAGS,
-		},
-		.drv = &anx7447_tcpm_drv,
-		.flags = TCPC_FLAGS_TCPCI_REV2_0,
-	},
-};
-
-/* USB Retimer */
-const struct usb_mux usbc1_retimer = {
-	.usb_port = 1,
-	.i2c_port = I2C_PORT_SUB_USB_C1,
-	.i2c_addr_flags = TUSB544_I2C_ADDR_FLAGS0,
-	.driver = &tusb544_drv,
-};
-
-/* USB Muxes */
-const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = {
-	{
-		.usb_port = 0,
-		.i2c_port = I2C_PORT_USB_C0,
-		.i2c_addr_flags = IT5205_I2C_ADDR1_FLAGS,
-		.driver = &it5205_usb_mux_driver,
-	},
-	{
-		.usb_port = 1,
-		.i2c_port = I2C_PORT_SUB_USB_C1,
-		.i2c_addr_flags = AN7447_TCPC0_I2C_ADDR_FLAGS,
-		.driver = &anx7447_usb_mux_driver,
-		.next_mux = &usbc1_retimer,
-	},
-};
-
-void board_init(void)
-{
-	int on;
-
-	gpio_enable_interrupt(GPIO_USB_C0_INT_ODL);
-	gpio_enable_interrupt(GPIO_USB_C1_INT_ODL);
-	gpio_enable_interrupt(GPIO_USB_C0_CCSBU_OVP_ODL);
-
-	/* Charger on the MB will be outputting PROCHOT_ODL and OD CHG_DET */
-	sm5803_configure_gpio0(CHARGER_PRIMARY, GPIO0_MODE_PROCHOT, 1);
-	sm5803_configure_chg_det_od(CHARGER_PRIMARY, 1);
-
-	/* Charger on the sub-board will be a push-pull GPIO */
-	sm5803_configure_gpio0(CHARGER_SECONDARY, GPIO0_MODE_OUTPUT, 0);
-
-	/* Turn on 5V if the system is on, otherwise turn it off */
-	on = chipset_in_state(CHIPSET_STATE_ON | CHIPSET_STATE_ANY_SUSPEND);
-	board_power_5v_enable(on);
-}
-DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
-
-void board_reset_pd_mcu(void)
-{
-	/*
-	 * Nothing to do.  TCPC C0 is internal, TCPC C1 reset pin is not
-	 * connected to the EC.
-	 */
-}
-
-__override void board_power_5v_enable(int enable)
-{
-	/*
-	 * Motherboard has a GPIO to turn on the 5V regulator, but the sub-board
-	 * sets it through the charger GPIO.
-	 */
-	gpio_set_level(GPIO_EN_PP5000, !!enable);
-	if (sm5803_set_gpio0_level(1, !!enable))
-		CPRINTUSB("Failed to %sable sub rails!", enable ? "en" : "dis");
-}
-
-uint16_t tcpc_get_alert_status(void)
-{
-	/*
-	 * TCPC 0 is embedded in the EC and processes interrupts in the chip
-	 * code (it83xx/intc.c)
-	 */
-
-	uint16_t status = 0;
-	int regval;
-
-	/* Check whether TCPC 1 pulled the shared interrupt line */
-	if (!gpio_get_level(GPIO_USB_C1_INT_ODL)) {
-		if (!tcpc_read16(1, TCPC_REG_ALERT, &regval)) {
-			if (regval)
-				status = PD_STATUS_TCPC_ALERT_1;
-		}
-	}
-
-	return status;
-}
-
-int extpower_is_present(void)
-{
-	int chg0 = 0;
-	int chg1 = 0;
-
-	sm5803_get_chg_det(0, &chg0);
-	sm5803_get_chg_det(1, &chg1);
-
-	return chg0 || chg1;
-}
-
-void board_set_charge_limit(int port, int supplier, int charge_ma, int max_ma,
-			    int charge_mv)
-{
-	int icl = MAX(charge_ma, CONFIG_CHARGER_INPUT_CURRENT);
-
-	/*
-	 * TODO(b/151955431): Characterize the input current limit in case a
-	 * scaling needs to be applied here
-	 */
-	charge_set_input_current_limit(icl, charge_mv);
-}
-
-int board_set_active_charge_port(int port)
-{
-	int is_valid_port = (port >= 0 && port < CONFIG_USB_PD_PORT_MAX_COUNT);
-	int p0_otg, p1_otg;
-
-	if (!is_valid_port && port != CHARGE_PORT_NONE)
-		return EC_ERROR_INVAL;
-
-	/* TODO(b/147440290): charger functions should take chgnum */
-	p0_otg = chg_chips[0].drv->is_sourcing_otg_power(0, 0);
-	p1_otg = chg_chips[1].drv->is_sourcing_otg_power(1, 1);
-
-	if (port == CHARGE_PORT_NONE) {
-		CPRINTUSB("Disabling all charge ports");
-
-		if (!p0_otg)
-			chg_chips[0].drv->set_mode(0,
-						   CHARGE_FLAG_INHIBIT_CHARGE);
-		if (!p1_otg)
-			chg_chips[1].drv->set_mode(1,
-						   CHARGE_FLAG_INHIBIT_CHARGE);
-
-		return EC_SUCCESS;
-	}
-
-	CPRINTUSB("New chg p%d", port);
-
-	/*
-	 * Charger task will take care of enabling charging on the new charge
-	 * port.  Here, we ensure the other port is not charging by changing
-	 * CHG_EN
-	 */
-	if (port == 0) {
-		if (p0_otg) {
-			CPRINTUSB("Skip enable p%d", port);
-			return EC_ERROR_INVAL;
-		}
-		if (!p1_otg) {
-			chg_chips[1].drv->set_mode(1,
-						   CHARGE_FLAG_INHIBIT_CHARGE);
-		}
-	} else {
-		if (p1_otg) {
-			CPRINTUSB("Skip enable p%d", port);
-			return EC_ERROR_INVAL;
-		}
-		if (!p0_otg) {
-			chg_chips[0].drv->set_mode(0,
-						   CHARGE_FLAG_INHIBIT_CHARGE);
-		}
-	}
-
-	return EC_SUCCESS;
-}
-
-/* Vconn control for integrated ITE TCPC */
-void board_pd_vconn_ctrl(int port, enum usbpd_cc_pin cc_pin, int enabled)
-{
-	/* Vconn control is only for port 0 */
-	if (port)
-		return;
-
-	if (cc_pin == USBPD_CC_PIN_1)
-		gpio_set_level(GPIO_EN_USB_C0_CC1_VCONN, !!enabled);
-	else
-		gpio_set_level(GPIO_EN_USB_C0_CC2_VCONN, !!enabled);
-}
-
-__override void typec_set_source_current_limit(int port, enum tcpc_rp_value rp)
-{
-	int current;
-
-	if (port < 0 || port > CONFIG_USB_PD_PORT_MAX_COUNT)
-		return;
-
-	current = (rp == TYPEC_RP_3A0) ? 3000 : 1500;
-
-	chg_chips[port].drv->set_otg_current_voltage(port, current, 5000);
-}
-
-/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */
-const struct pwm_t pwm_channels[] = {
-	[PWM_CH_KBLIGHT] = {
-		.channel = 0,
-		.flags = PWM_CONFIG_DSLEEP,
-		.freq_hz = 10000,
-	},
-
-	[PWM_CH_LED_RED] = {
-		.channel = 1,
-		.flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW,
-		.freq_hz = 2400,
-	},
-
-	[PWM_CH_LED_GREEN] = {
-		.channel = 2,
-		.flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW,
-		.freq_hz = 2400,
-	},
-
-	[PWM_CH_LED_BLUE] = {
-		.channel = 3,
-		.flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW,
-		.freq_hz = 2400,
-	}
-
-};
-BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
-
-/* Sensor Mutexes */
-static struct mutex g_lid_mutex;
-static struct mutex g_base_mutex;
-
-/* Sensor Data */
-static struct stprivate_data g_lis2dh_data;
-static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA;
-
-/* Drivers */
-struct motion_sensor_t motion_sensors[] = {
-	[LID_ACCEL] = {
-		.name = "Lid Accel",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_LIS2DE,
-		.type = MOTIONSENSE_TYPE_ACCEL,
-		.location = MOTIONSENSE_LOC_LID,
-		.drv = &lis2dh_drv,
-		.mutex = &g_lid_mutex,
-		.drv_data = &g_lis2dh_data,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = LIS2DH_ADDR1_FLAGS,
-		.rot_standard_ref = NULL,
-		.default_range = 2, /* g */
-		/* We only use 2g because its resolution is only 8-bits */
-		.min_frequency = LIS2DH_ODR_MIN_VAL,
-		.max_frequency = LIS2DH_ODR_MAX_VAL,
-		.config = {
-			[SENSOR_CONFIG_EC_S0] = {
-				.odr = 10000 | ROUND_UP_FLAG,
-			},
-			[SENSOR_CONFIG_EC_S3] = {
-				.odr = 10000 | ROUND_UP_FLAG,
-			},
-		},
-	},
-	[BASE_ACCEL] = {
-		.name = "Base Accel",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_LSM6DSM,
-		.type = MOTIONSENSE_TYPE_ACCEL,
-		.location = MOTIONSENSE_LOC_BASE,
-		.drv = &lsm6dsm_drv,
-		.mutex = &g_base_mutex,
-		.drv_data = LSM6DSM_ST_DATA(lsm6dsm_data,
-				MOTIONSENSE_TYPE_ACCEL),
-		.int_signal = GPIO_BASE_SIXAXIS_INT_L,
-		.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
-		.rot_standard_ref = NULL,
-		.default_range = 4,  /* g */
-		.min_frequency = LSM6DSM_ODR_MIN_VAL,
-		.max_frequency = LSM6DSM_ODR_MAX_VAL,
-		.config = {
-			[SENSOR_CONFIG_EC_S0] = {
-				.odr = 13000 | ROUND_UP_FLAG,
-				.ec_rate = 100 * MSEC,
-			},
-			[SENSOR_CONFIG_EC_S3] = {
-				.odr = 10000 | ROUND_UP_FLAG,
-				.ec_rate = 100 * MSEC,
-			},
-		},
-	},
-	[BASE_GYRO] = {
-		.name = "Base Gyro",
-		.active_mask = SENSOR_ACTIVE_S0_S3,
-		.chip = MOTIONSENSE_CHIP_LSM6DSM,
-		.type = MOTIONSENSE_TYPE_GYRO,
-		.location = MOTIONSENSE_LOC_BASE,
-		.drv = &lsm6dsm_drv,
-		.mutex = &g_base_mutex,
-		.drv_data = LSM6DSM_ST_DATA(lsm6dsm_data,
-				MOTIONSENSE_TYPE_GYRO),
-		.int_signal = GPIO_BASE_SIXAXIS_INT_L,
-		.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
-		.port = I2C_PORT_SENSOR,
-		.i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
-		.default_range = 1000 | ROUND_UP_FLAG, /* dps */
-		.rot_standard_ref = NULL,
-		.min_frequency = LSM6DSM_ODR_MIN_VAL,
-		.max_frequency = LSM6DSM_ODR_MAX_VAL,
-	},
-	[VSYNC] = {
-		.name = "Camera VSYNC",
-		.active_mask = SENSOR_ACTIVE_S0,
-		.chip = MOTIONSENSE_CHIP_GPIO,
-		.type = MOTIONSENSE_TYPE_SYNC,
-		.location = MOTIONSENSE_LOC_CAMERA,
-		.drv = &sync_drv,
-		.default_range = 0,
-		.min_frequency = 0,
-		.max_frequency = 1,
-	},
-};
-
-const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
-
-/* Thermistors */
-const struct temp_sensor_t temp_sensors[] = {
-	[TEMP_SENSOR_1] = {.name = "Memory",
-			   .type = TEMP_SENSOR_TYPE_BOARD,
-			   .read = get_temp_3v3_51k1_47k_4050b,
-			   .idx = ADC_TEMP_SENSOR_1},
-	[TEMP_SENSOR_2] = {.name = "Ambient",
-			   .type = TEMP_SENSOR_TYPE_BOARD,
-			   .read = get_temp_3v3_51k1_47k_4050b,
-			   .idx = ADC_TEMP_SENSOR_2},
-};
-BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT);
-
-#ifndef TEST_BUILD
-/* This callback disables keyboard when convertibles are fully open */
-void lid_angle_peripheral_enable(int enable)
-{
-	int chipset_in_s0 = chipset_in_state(CHIPSET_STATE_ON);
-
-	/*
-	 * If the lid is in tablet position via other sensors,
-	 * ignore the lid angle, which might be faulty then
-	 * disable keyboard.
-	 */
-	if (tablet_get_mode())
-		enable = 0;
-
-	if (enable) {
-		keyboard_scan_enable(1, KB_SCAN_DISABLE_LID_ANGLE);
-	} else {
-		/*
-		 * Ensure that the chipset is off before disabling the keyboard.
-		 * When the chipset is on, the EC keeps the keyboard enabled and
-		 * the AP decides whether to ignore input devices or not.
-		 */
-		if (!chipset_in_s0)
-			keyboard_scan_enable(0, KB_SCAN_DISABLE_LID_ANGLE);
-	}
-}
-#endif
diff --git a/board/wheelie/board.h b/board/wheelie/board.h
deleted file mode 100644
index a4509bb625..0000000000
--- a/board/wheelie/board.h
+++ /dev/null
@@ -1,142 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Wheelie board configuration */
-
-#ifndef __CROS_EC_BOARD_H
-#define __CROS_EC_BOARD_H
-
-/* Select Baseboard features */
-#define VARIANT_DEDEDE_EC_IT8320
-#include "baseboard.h"
-
-/* System unlocked in early development */
-#define CONFIG_SYSTEM_UNLOCKED
-
-/* Battery */
-#define CONFIG_BATTERY_FUEL_GAUGE
-
-/* BC 1.2 */
-#define CONFIG_BC12_DETECT_PI3USB9201
-
-/* Charger */
-#define CONFIG_CHARGER_SM5803		/* C0 and C1: Charger */
-#define CONFIG_FPU			/* For charger calculations */
-#define CONFIG_USB_PD_VBUS_DETECT_CHARGER
-#define CONFIG_USB_PD_5V_CHARGER_CTRL
-#define CONFIG_CHARGER_OTG
-#undef  CONFIG_CHARGER_SINGLE_CHIP
-
-/* LED */
-#define CONFIG_LED_PWM
-#define CONFIG_LED_PWM_COUNT 1
-
-/* Sensors */
-#define CONFIG_ACCEL_LIS2DE		/* Lid accel */
-#define CONFIG_ACCELGYRO_LSM6DSM	/* Base accel */
-#define CONFIG_SYNC			/* Camera VSYNC */
-/* Sensors without hardware FIFO are in forced mode */
-#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
-
-#define CONFIG_ACCEL_INTERRUPTS
-/* Enable sensor fifo, must also define the _SIZE and _THRES */
-#define CONFIG_ACCEL_FIFO
-/* Power of 2 - Too large of a fifo causes too much timestamp jitter */
-#define CONFIG_ACCEL_FIFO_SIZE 256
-#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
-
-#define CONFIG_LID_ANGLE
-#define CONFIG_LID_ANGLE_UPDATE
-#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
-#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
-
-#define CONFIG_SYNC_INT_EVENT \
-	TASK_EVENT_MOTION_SENSOR_INTERRUPT(VSYNC)
-
-#define CONFIG_TABLET_MODE
-#define CONFIG_TABLET_MODE_SWITCH
-#define CONFIG_GMR_TABLET_MODE
-
-/* TCPC */
-#define CONFIG_USB_PD_PORT_MAX_COUNT 2
-#define CONFIG_USB_PD_TCPM_ITE_ON_CHIP	/* C0: ITE EC TCPC */
-#define CONFIG_USB_PD_TCPM_ANX7447	/* C1: ANX TCPC + Mux */
-#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 1
-
-/* Thermistors */
-#define CONFIG_TEMP_SENSOR
-#define CONFIG_THERMISTOR
-#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
-#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_PP3300_A
-
-/* USB Mux and Retimer */
-#define CONFIG_USB_MUX_IT5205			/* C1: ITE Mux */
-#define I2C_PORT_USB_MUX I2C_PORT_USB_C0	/* Required for ITE Mux */
-
-#define CONFIG_USBC_RETIMER_TUSB544		/* C1 Redriver: TUSB544 */
-
-#ifndef __ASSEMBLER__
-
-#include "gpio_signal.h"
-#include "registers.h"
-
-enum chg_id {
-	CHARGER_PRIMARY,
-	CHARGER_SECONDARY,
-	CHARGER_NUM,
-};
-
-enum pwm_channel {
-	PWM_CH_KBLIGHT,
-	PWM_CH_LED_RED,
-	PWM_CH_LED_GREEN,
-	PWM_CH_LED_BLUE,
-	PWM_CH_COUNT,
-};
-
-/* Motion sensors */
-enum sensor_id {
-	LID_ACCEL,
-	BASE_ACCEL,
-	BASE_GYRO,
-	VSYNC,
-	SENSOR_COUNT
-};
-
-/* ADC channels */
-enum adc_channel {
-	ADC_VSNS_PP3300_A,     /* ADC0 */
-	ADC_TEMP_SENSOR_1,     /* ADC2 */
-	ADC_TEMP_SENSOR_2,     /* ADC3 */
-	ADC_SUB_ANALOG,        /* ADC13 */
-	ADC_CH_COUNT
-};
-
-enum temp_sensor_id {
-	TEMP_SENSOR_1,
-	TEMP_SENSOR_2,
-	TEMP_SENSOR_COUNT
-};
-
-/* List of possible batteries */
-enum battery_type {
-	BATTERY_LGC15,
-	BATTERY_PANASONIC_AP15O5L,
-	BATTERY_SANYO,
-	BATTERY_SONY,
-	BATTERY_SMP_AP13J7K,
-	BATTERY_PANASONIC_AC15A3J,
-	BATTERY_LGC_AP18C8K,
-	BATTERY_MURATA_AP18C4K,
-	BATTERY_LGC_AP19A8K,
-	BATTERY_LGC_G023,
-	BATTERY_TYPE_COUNT,
-};
-
-int board_is_sourcing_vbus(int port);
-
-#endif /* !__ASSEMBLER__ */
-
-#endif /* __CROS_EC_BOARD_H */
diff --git a/board/wheelie/build.mk b/board/wheelie/build.mk
deleted file mode 100644
index 00e4e0bb5d..0000000000
--- a/board/wheelie/build.mk
+++ /dev/null
@@ -1,15 +0,0 @@
-# -*- makefile -*-
-# Copyright 2020 The Chromium OS Authors. All rights reserved.
-# Use of this source code is governed by a BSD-style license that can be
-# found in the LICENSE file.
-#
-# Board specific files build
-#
-
-CHIP:=it83xx
-CHIP_FAMILY:=it8320
-CHIP_VARIANT:=it8320dx
-BASEBOARD:=dedede
-
-board-y=board.o led.o usb_pd_policy.o
-board-$(CONFIG_BATTERY_SMART)+=battery.o
diff --git a/board/wheelie/ec.tasklist b/board/wheelie/ec.tasklist
deleted file mode 100644
index 75181a4531..0000000000
--- a/board/wheelie/ec.tasklist
+++ /dev/null
@@ -1,24 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/*
- * See CONFIG_TASK_LIST in config.h for details.
- */
-
-#define CONFIG_TASK_LIST \
-	TASK_ALWAYS(HOOKS, hook_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_ALWAYS(MOTIONSENSE, motion_sense_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_ALWAYS(USB_CHG_P0, usb_charger_task, 0, LARGER_TASK_STACK_SIZE) \
-	TASK_ALWAYS(USB_CHG_P1, usb_charger_task, 1, LARGER_TASK_STACK_SIZE) \
-	TASK_ALWAYS(CHARGER, charger_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_NOTEST(CHIPSET, chipset_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_NOTEST(KEYPROTO, keyboard_protocol_task, NULL, TASK_STACK_SIZE) \
-	TASK_ALWAYS(HOSTCMD, host_command_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_ALWAYS(CONSOLE, console_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_ALWAYS(POWERBTN, power_button_task, NULL, VENTI_TASK_STACK_SIZE) \
-	TASK_NOTEST(KEYSCAN, keyboard_scan_task, NULL, TASK_STACK_SIZE) \
-        TASK_ALWAYS(PD_C0, pd_task, NULL, ULTRA_TASK_STACK_SIZE) \
-        TASK_ALWAYS(PD_C1, pd_task, NULL, ULTRA_TASK_STACK_SIZE) \
-        TASK_ALWAYS(PD_INT_C1, pd_interrupt_handler_task, 1, ULTRA_TASK_STACK_SIZE)
diff --git a/board/wheelie/gpio.inc b/board/wheelie/gpio.inc
deleted file mode 100644
index 1d6838729a..0000000000
--- a/board/wheelie/gpio.inc
+++ /dev/null
@@ -1,140 +0,0 @@
-/* -*- mode:c -*-
- *
- * Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Declare symbolic names for all the GPIOs that we care about.
- * Note: Those with interrupt handlers must be declared first. */
-
-/* Power State interrupts */
-GPIO_INT(SLP_S4_L,		PIN(I, 5), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(SLP_S3_L,		PIN(H, 3), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt)
-GPIO_INT(SLP_S0_L,		PIN(E, 4), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(SLP_SUS_L,		PIN(G, 2), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(VCCIN_AUX_VID0,	PIN(D, 0), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(RSMRST_PWRGD_L,	PIN(E, 1), GPIO_INT_BOTH | GPIO_PULL_UP, power_signal_interrupt)
-GPIO_INT(CPU_C10_GATE_L,	PIN(G, 1), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(PG_DRAM_OD,		PIN(D, 3), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt)
-GPIO_INT(PG_PP1050_ST_OD,	PIN(L, 1), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(VCCIN_AUX_VID1,	PIN(K, 1), GPIO_INT_BOTH, power_signal_interrupt)
-GPIO_INT(PG_VCCIO_EXT_OD,	PIN(D, 7), GPIO_INT_BOTH, baseboard_all_sys_pgood_interrupt)
-GPIO_INT(ESPI_RESET_L, 	 PIN(D, 2), GPIO_INT_FALLING | GPIO_SEL_1P8V, espi_reset_pin_asserted_interrupt)
-
-GPIO_INT(H1_EC_PWR_BTN_ODL,	PIN(E, 2), GPIO_INT_BOTH | GPIO_PULL_UP, power_button_interrupt)
-#ifdef CONFIG_LOW_POWER_IDLE
-/* Used to wake up the EC from Deep Doze mode when writing to console */
-GPIO_INT(UART1_RX,	 PIN(B, 0), GPIO_INT_BOTH, uart_deepsleep_interrupt)	/* UART_DBG_TX_EC_RX */
-#endif
-
-/* USB-C interrupts */
-GPIO_INT(USB_C0_INT_ODL,	PIN(K, 0), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c0_interrupt) /* BC12 and charger */
-GPIO_INT(USB_C1_INT_ODL,	PIN(B, 5), GPIO_INT_FALLING | GPIO_PULL_UP, usb_c1_interrupt) /* TCPC, charger, BC12 */
-GPIO_INT(USB_C0_CCSBU_OVP_ODL,	PIN(K, 6), GPIO_INT_FALLING | GPIO_PULL_UP, c0_ccsbu_ovp_interrupt) /* Fault protection */
-
-/* Other interrupts */
-GPIO_INT(LID_OPEN,		PIN(F, 3), GPIO_INT_BOTH, lid_interrupt)
-GPIO_INT(LID_360_L,		PIN(A, 7), GPIO_INT_BOTH, gmr_tablet_switch_isr)
-GPIO_INT(VOLDN_BTN_ODL,		PIN(I, 6), GPIO_INT_BOTH, button_interrupt)
-GPIO_INT(VOLUP_BTN_ODL,		PIN(I, 7), GPIO_INT_BOTH, button_interrupt)
-GPIO_INT(BASE_SIXAXIS_INT_L,	PIN(J, 0), GPIO_INT_FALLING | GPIO_SEL_1P8V, lsm6dsm_interrupt)
-GPIO_INT(CAM_EC_VSYNC,		PIN(C, 7), GPIO_INT_RISING, sync_interrupt)
-GPIO_INT(EC_WP_OD,		PIN(A, 6), GPIO_INT_BOTH, switch_interrupt)
-
-/* Power sequence GPIOs */
-GPIO(EC_AP_RTCRST,		PIN(K, 2), GPIO_OUT_LOW)
-GPIO(EC_AP_PWR_BTN_ODL,		PIN(B, 6), GPIO_ODR_HIGH)
-GPIO(EC_AP_DPWROK,		PIN(L, 7), GPIO_OUT_LOW)
-GPIO(EC_AP_RSMRST_L,		PIN(H, 0), GPIO_OUT_LOW)
-GPIO(EC_AP_WAKE_ODL,		PIN(D, 5), GPIO_ODR_HIGH)
-GPIO(SYS_RST_ODL,		PIN(D, 1), GPIO_ODR_HIGH)
-GPIO(EC_AP_SYS_PWROK,		PIN(F, 2), GPIO_OUT_LOW)
-GPIO(PG_PP5000_U_OD,		PIN(E, 3), GPIO_INPUT)
-GPIO(EN_PP3300_PEN,		PIN(E, 6), GPIO_OUT_LOW)
-GPIO(EN_PP3300_A,		PIN(C, 5), GPIO_OUT_LOW)
-GPIO(EC_AP_PCH_PWROK_OD,	PIN(D, 6), GPIO_ODR_LOW)
-GPIO(EN_PP5000_U,		PIN(K, 5), GPIO_OUT_LOW)
-/* TODO(b:149775160) - Modify if needed if we ever use this signal. */
-GPIO(EN_VCCST,			PIN(D, 4), GPIO_INPUT)
-GPIO(EN_VCCIO_EXT,		PIN(B, 2), GPIO_OUT_LOW)
-GPIO(EC_PROCHOT_ODL,		PIN(I, 1), GPIO_ODR_HIGH | GPIO_SEL_1P8V)
-GPIO(EC_AP_VCCST_PWRGD_OD,	PIN(E, 5), GPIO_ODR_LOW)
-GPIO(ALL_SYS_PWRGD,		PIN(B, 7), GPIO_OUT_LOW)
-GPIO(EN_SLP_Z,			PIN(K, 3), GPIO_OUT_LOW)
-
-/* Required for icelake chipset code, but implemented through other means for dedede */
-UNIMPLEMENTED(PG_EC_DSW_PWROK)
-UNIMPLEMENTED(PG_EC_ALL_SYS_PWRGD)
-
-/* I2C pins - Alternate function below configures I2C module on these pins */
-GPIO(EC_I2C_EEPROM_SCL,		PIN(B, 3), GPIO_INPUT)
-GPIO(EC_I2C_EEPROM_SDA,		PIN(B, 4), GPIO_INPUT)
-GPIO(EC_I2C_BATTERY_SCL,	PIN(C, 1), GPIO_INPUT)
-GPIO(EC_I2C_BATTERY_SDA,	PIN(C, 2), GPIO_INPUT)
-GPIO(EC_I2C_SENSOR_SCL,		PIN(F, 6), GPIO_INPUT | GPIO_SEL_1P8V)
-GPIO(EC_I2C_SENSOR_SDA,		PIN(F, 7), GPIO_INPUT | GPIO_SEL_1P8V)
-GPIO(EC_I2C_SUB_USB_C1_SCL,	PIN(E, 0), GPIO_INPUT)
-GPIO(EC_I2C_SUB_USB_C1_SDA,	PIN(E, 7), GPIO_INPUT)
-GPIO(EC_I2C_USB_C0_SCL,		PIN(A, 4), GPIO_INPUT)
-GPIO(EC_I2C_USB_C0_SDA,		PIN(A, 5), GPIO_INPUT)
-
-/* USB pins */
-GPIO(EN_USB_C0_CC1_VCONN,	PIN(H, 4), GPIO_OUT_LOW)
-GPIO(EN_USB_C0_CC2_VCONN,	PIN(H, 6), GPIO_OUT_LOW)
-GPIO(EC_AP_USB_C0_HPD,		PIN(L, 4), GPIO_OUT_LOW)
-GPIO(EC_AP_USB_C1_HDMI_HPD,	PIN(K, 7), GPIO_OUT_LOW)
-GPIO(USB_C0_FRS,		PIN(C, 4), GPIO_OUT_LOW)
-GPIO(HDMI_SEL_L,		PIN(C, 6), GPIO_OUT_HIGH)
-
-/* MKBP event synchronization */
-GPIO(EC_AP_MKBP_INT_L,	PIN(L, 5), GPIO_ODR_HIGH)
-
-/* Misc pins which will run to the I/O board */
-GPIO(EC_SUB_IO_1_1, PIN(L, 3), GPIO_INPUT)
-GPIO(EC_SUB_IO_1_2, PIN(F, 0), GPIO_INPUT)
-GPIO(EC_SUB_IO_2_1, PIN(F, 1), GPIO_INPUT)
-GPIO(EC_SUB_IO_2_2, PIN(L, 2), GPIO_INPUT)
-
-/* Misc */
-GPIO(EN_BL_OD,			PIN(K, 4), GPIO_OUT_LOW)
-GPIO(EC_ENTERING_RW,		PIN(G, 0), GPIO_OUT_LOW)
-GPIO(CCD_MODE_ODL,		PIN(H, 5), GPIO_INPUT)
-GPIO(EC_BATTERY_PRES_ODL,	PIN(I, 4), GPIO_INPUT)
-GPIO(PEN_DET_ODL,		PIN(J, 1), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(EN_KB_BL,			PIN(J, 3), GPIO_OUT_LOW) /* Currently unused */
-
-/* NC pins, enable internal pull-down to avoid floating state. */
-GPIO(GPIOC0_NC, PIN(C, 0), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOC3_NC, PIN(C, 3), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOG3_NC, PIN(G, 3), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOG4_NC, PIN(G, 4), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOG5_NC, PIN(G, 5), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOG6_NC, PIN(G, 6), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOG7_NC, PIN(G, 7), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOJ4_NC, PIN(J, 4), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOJ5_NC, PIN(J, 5), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOJ6_NC, PIN(J, 6), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOL6_NC, PIN(L, 6), GPIO_INPUT | GPIO_PULL_DOWN)
-GPIO(GPIOM6_NC, PIN(M, 6), GPIO_INPUT | GPIO_PULL_DOWN)
-
-/* Alternate functions GPIO definitions */
-/* UART */
-ALTERNATE(PIN_MASK(B, BIT(0) | BIT(1)), 0, MODULE_UART, 0)		/* UART for debug */
-
-/* I2C */
-ALTERNATE(PIN_MASK(B, BIT(3) | BIT(4)), 0, MODULE_I2C, 0)		/* I2C0 */
-ALTERNATE(PIN_MASK(C, BIT(1) | BIT(2)), 0, MODULE_I2C, 0)		/* I2C1 */
-ALTERNATE(PIN_MASK(F, BIT(6) | BIT(7)), 0, MODULE_I2C, GPIO_SEL_1P8V)	/* I2C2 - 1.8V */
-ALTERNATE(PIN_MASK(E, BIT(0) | BIT(7)), 0, MODULE_I2C, 0)		/* I2C4 */
-ALTERNATE(PIN_MASK(A, BIT(4) | BIT(5)), 0, MODULE_I2C, 0)		/* I2C5 */
-
-/* ADC */
-ALTERNATE(PIN_MASK(L, BIT(0)), 0, MODULE_ADC, 0)			/* ADC13: EC_SUB_ANALOG */
-ALTERNATE(PIN_MASK(I, BIT(0) | BIT(2) | BIT(3)), 0, MODULE_ADC, 0)	/* ADC0: EC_VSNS_PP3300_A, ADC2: TEMP_SENSOR_1, ADC3: TEMP_SENSOR_2 */
-
-/* DAC */
-ALTERNATE(PIN_MASK(J, BIT(2)), 0, MODULE_DAC, 0)			/* DAC2: EC_AP_PSYS */
-
-/* PWM */
-ALTERNATE(PIN_MASK(A, BIT(0) | BIT(1) | BIT(2) | BIT(3)), 0, MODULE_PWM, 0) /* KB_BL_PWM, LED_[R,G,B]_ODL */
diff --git a/board/wheelie/led.c b/board/wheelie/led.c
deleted file mode 100644
index 8c65f54568..0000000000
--- a/board/wheelie/led.c
+++ /dev/null
@@ -1,82 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-/* Wheelie specific PWM LED settings. */
-
-#include "common.h"
-#include "ec_commands.h"
-#include "led_pwm.h"
-#include "pwm.h"
-#include "util.h"
-
-const enum ec_led_id supported_led_ids[] = {
-	EC_LED_ID_POWER_LED,
-};
-const int supported_led_ids_count = ARRAY_SIZE(supported_led_ids);
-
-/*
- * Board has one physical LED with red, green, and blue
- */
-struct pwm_led led_color_map[EC_LED_COLOR_COUNT] = {
-				/* Red, Green, Blue */
-	[EC_LED_COLOR_RED]    = { 100,   0,   0 },
-	[EC_LED_COLOR_GREEN]  = {   0, 100,   0 },
-	[EC_LED_COLOR_BLUE]   = {   0,   0, 100 },
-	[EC_LED_COLOR_YELLOW] = {  50,  50,   0 },
-	[EC_LED_COLOR_WHITE]  = {  50,  50,  50 },
-	[EC_LED_COLOR_AMBER]  = {  70,  30,   0 },
-};
-
-/* One logical LED with red, green, and blue channels. */
-struct pwm_led pwm_leds[CONFIG_LED_PWM_COUNT] = {
-	{
-		.ch0 = PWM_CH_LED_RED,
-		.ch1 = PWM_CH_LED_GREEN,
-		.ch2 = PWM_CH_LED_BLUE,
-		.enable = &pwm_enable,
-		.set_duty = &pwm_set_duty,
-	},
-};
-
-void led_get_brightness_range(enum ec_led_id led_id, uint8_t *brightness_range)
-{
-	memset(brightness_range, '\0',
-	       sizeof(*brightness_range) * EC_LED_COLOR_COUNT);
-	brightness_range[EC_LED_COLOR_RED] = 100;
-	brightness_range[EC_LED_COLOR_GREEN] = 100;
-	brightness_range[EC_LED_COLOR_BLUE] = 100;
-	brightness_range[EC_LED_COLOR_YELLOW] = 100;
-	brightness_range[EC_LED_COLOR_WHITE] = 100;
-	brightness_range[EC_LED_COLOR_AMBER] = 100;
-}
-
-int led_set_brightness(enum ec_led_id led_id, const uint8_t *brightness)
-{
-	enum pwm_led_id pwm_id;
-
-	/* Convert ec_led_id to pwm_led_id. */
-	if (led_id == EC_LED_ID_POWER_LED)
-		pwm_id = PWM_LED0;
-	else
-		return EC_ERROR_UNKNOWN;
-
-	if (brightness[EC_LED_COLOR_RED])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_RED);
-	else if (brightness[EC_LED_COLOR_GREEN])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_GREEN);
-	else if (brightness[EC_LED_COLOR_BLUE])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_BLUE);
-	else if (brightness[EC_LED_COLOR_YELLOW])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_YELLOW);
-	else if (brightness[EC_LED_COLOR_WHITE])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_WHITE);
-	else if (brightness[EC_LED_COLOR_AMBER])
-		set_pwm_led_color(pwm_id, EC_LED_COLOR_AMBER);
-	else
-		/* Otherwise, the "color" is "off". */
-		set_pwm_led_color(pwm_id, -1);
-
-	return EC_SUCCESS;
-}
diff --git a/board/wheelie/usb_pd_policy.c b/board/wheelie/usb_pd_policy.c
deleted file mode 100644
index 1611af23e0..0000000000
--- a/board/wheelie/usb_pd_policy.c
+++ /dev/null
@@ -1,84 +0,0 @@
-/* Copyright 2020 The Chromium OS Authors. All rights reserved.
- * Use of this source code is governed by a BSD-style license that can be
- * found in the LICENSE file.
- */
-
-#include "battery_smart.h"
-#include "charge_manager.h"
-#include "charger.h"
-#include "chipset.h"
-#include "common.h"
-#include "console.h"
-#include "driver/charger/sm5803.h"
-#include "driver/tcpm/tcpci.h"
-#include "usb_pd.h"
-
-#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args)
-#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args)
-
-int pd_check_vconn_swap(int port)
-{
-	/* Allow VCONN swaps if the AP is on */
-	return chipset_in_state(CHIPSET_STATE_ANY_SUSPEND | CHIPSET_STATE_ON);
-}
-
-void pd_power_supply_reset(int port)
-{
-	int prev_en;
-
-	if (port < 0 || port >= CONFIG_USB_PD_PORT_MAX_COUNT)
-		return;
-
-	/* TODO(b/147440290): charger functions should take chgnum */
-	prev_en = chg_chips[port].drv->is_sourcing_otg_power(port, port);
-
-	/* Disable Vbus */
-	chg_chips[port].drv->enable_otg_power(port, 0);
-
-	/* Discharge Vbus if previously enabled */
-	if (prev_en)
-		sm5803_set_vbus_disch(port, 1);
-
-#ifdef CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
-	/* Give back the current quota we are no longer using */
-	charge_manager_source_port(port, 0);
-#endif /* defined(CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT) */
-
-	/* Notify host of power info change. */
-	pd_send_host_event(PD_EVENT_POWER_CHANGE);
-}
-
-int pd_set_power_supply_ready(int port)
-{
-	enum ec_error_list rv;
-
-	/* Disable charging */
-	rv = chg_chips[port].drv->set_mode(port, CHARGE_FLAG_INHIBIT_CHARGE);
-	if (rv)
-		return rv;
-
-	/* Disable Vbus discharge */
-	sm5803_set_vbus_disch(port, 0);
-
-	/* Provide Vbus */
-	chg_chips[port].drv->enable_otg_power(port, 1);
-
-#ifdef CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
-	/* Ensure we advertise the proper available current quota */
-	charge_manager_source_port(port, 1);
-#endif /* defined(CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT) */
-
-	/* Notify host of power info change. */
-	pd_send_host_event(PD_EVENT_POWER_CHANGE);
-
-	return EC_SUCCESS;
-}
-
-int pd_snk_is_vbus_provided(int port)
-{
-	int chg_det = 0;
-
-	sm5803_get_chg_det(port, &chg_det);
-
-	return chg_det;
-}