summaryrefslogtreecommitdiff
path: root/include/configs/p1_twr.h
Commit message (Collapse)AuthorAgeFilesLines
* powerpc: Remove TWR-P1025_defconfig boardJagan Teki2020-06-181-480/+0
| | | | | | | | | | | DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* common: Drop linux/stringify.h from common headerSimon Glass2020-05-181-0/+2
| | | | | | Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
* treewide: mem: Move mtest related defines to KconfigWIP/2020-05-07-more-kconfig-migrationsAshok Reddy Soma2020-05-081-3/+0
| | | | | | | | | | | Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_PHYLIB et al to KconfigTom Rini2020-04-281-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-8/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* powerpc: mpc85xx: Move CONFIG_FSL_PCIE_RESET to KconfigHou Zhiqiang2019-06-201-1/+0
| | | | | | | Use the Kconfig option to select the PCIe reset errata. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
* configs: Migrate CONFIG_FMAN_ENET and some related options to KconfigTom Rini2019-05-261-2/+0
| | | | | | | | | Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini <trini@konsulko.com>
* spi: Zap CONFIG_HARD_SPIJagan Teki2018-11-271-5/+0
| | | | | | | | | | In legacy CONFIG_HARD_SPI initalizing spi_init code, which was removed during dm conversion cleanup. So remove the dead instances of CONFIG_HARD_SPI, and related code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
* Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford2018-10-191-4/+0
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: drop CONFIG_SYS_EXTRA_ENV_RELOCSimon Goldschmidt2018-10-061-1/+0
| | | | | | | | | | | | Instead of manually specifying CONFIG_SYS_EXTRA_ENV_RELOC for every board that needs it, it shouldn't hurt to let initr_reloc_global_data() always relocate gd->env_addr unless we know this pointer is outside the initial binary. To achieve this, the relocation is omitted if CONFIG_ENV_ADDR is defined (and ENV_IS_EMBEDDED is not). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* Convert CONFIG_MII et al to KconfigAdam Ford2018-08-171-1/+0
| | | | | | | | | | This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford2018-07-221-2/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
* cmd: Kconfig: Move CONFIG_MP to KconfigSiva Durga Prasad Paladugu2018-07-101-2/+0
| | | | | | | This patch moves CONFIG_MP to Kconfig Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini2018-05-071-2/+1
| | | | | | | | | | | | | | | | | | | | When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
* treewide: Convert CONFIG_HOSTNAME to a string optionMario Six2018-04-081-1/+1
| | | | | | | | | CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every use is couched by __stringify(...). Hence, convert it to a proper string option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six2018-04-081-1/+0
| | | | | | Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* treewide: Migrate CONFIG_TSEC_ENET to KconfigMario Six2018-04-081-1/+0
| | | | | | Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to KconfigMario Six2018-04-081-2/+0
| | | | | | Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* Convert all of CONFIG_CONS_INDEX to KconfigTom Rini2018-03-161-1/+0
| | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford2018-02-231-2/+0
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_SYS_TEXT_BASETom Rini2018-02-111-5/+0
| | | | | | | | | | | On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
* Move CONFIG_PANIC_HANG to KconfigMasahiro Yamada2017-12-261-1/+0
| | | | | | | | Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
* ata: Migrate CONFIG_LIBATA to KconfigTuomas Tynkkynen2017-12-121-1/+0
| | | | | | | | This symbol enables some library code used by various SATA drivers, so make this a non-user-visible symbol select'ed by the respective drivers, and let moveconfig handle the rest. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* ata: Migrate CONFIG_SATA_SIL3114 to KconfigTuomas Tynkkynen2017-12-121-1/+0
| | | | Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULTTom Rini2017-11-051-4/+0
| | | | | | | | | | We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: Tom Rini <trini@konsulko.com>
* include/configs: remove numerous CONFIG_SYS_BARGSIZE definitionsThomas Petazzoni2017-09-031-1/+0
| | | | | | | | | | | | | | | | | | | | | This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be equal to CONFIG_SYS_CBSIZE in numerous configuration files. We remove such definitions in two situations: - CONFIG_SYS_CBSIZE is otherwise not defined in the board configuration file, which means the default value of CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is larger. - CONFIG_SYS_CBSIZE is defined in the board configuration file, but to a value equal or less than 512. In this case, the default value of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it is equal or larger. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_MAXARGSThomas Petazzoni2017-09-031-1/+0
| | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: drop default definitions of CONFIG_SYS_PBSIZEThomas Petazzoni2017-09-031-2/+0
| | | | | | | | | Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* include/configs: remove CONFIG_SYS_CBSIZE when the default value is usedThomas Petazzoni2017-09-031-5/+0
| | | | | | | | | | | Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_CBSIZE, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Drop <config.h> from stih410-b2260.h] Signed-off-by: Tom Rini <trini@konsulko.com>
* common: Move CONFIG_BOOTARGS to KconfigSam Protsenko2017-08-141-2/+0
| | | | | | | | | Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_REGINFO to KconfigChristophe Leroy2017-08-111-5/+0
| | | | | | | | | This patch converts CONFIG_CMD_REGINFO to Kconfig Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
* Convert CONFIG_CMD_PCI to KconfigSimon Glass2017-08-111-2/+0
| | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
* configs: Finish migration of PHY_GIGETom Rini2017-08-081-2/+0
| | | | | Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ENV_IS_IN_FLASH to KconfigSimon Glass2017-07-251-1/+0
| | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_FLASH Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to KconfigSimon Glass2017-07-251-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFSTom Rini2017-07-241-1/+0
| | | | | | | | The above CONFIG options are in Kconfig, and now have correct depends and inter-dependencies. Migrate these to configs/ from include/configs/. In the case of CMD_UBIFS also change it to be a default y if CMD_UBI. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_SATA to KconfigSimon Glass2017-07-111-1/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_CMD_SATA Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* Convert CONFIG_CMD_IRQ to KconfigSimon Glass2017-05-221-1/+0
| | | | | | | | This converts the following to Kconfig: CONFIG_CMD_IRQ Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CMD_EEPROM et al to KconfigSimon Glass2017-05-221-1/+0
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_EEPROM_LAYOUT_HELP_STRING Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Rework Kconfig logic slightly, define EEPROM location on TI eval platforms] Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to KconfigTom Rini2017-05-151-2/+0
| | | | | | | | | | Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig. For a few SoCs, imply or default y this if USB is enabled. In some cases we had not already migrated to CONFIG_USB so do that as well. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
* Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCDTom Rini2017-05-151-2/+2
| | | | | | | | | | In order to be able to migrate the various SoC EHCI CONFIG options we first need to finish the switch from CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marek Vasut <marex@denx.de>
* Kconfig: Migrate CONFIG_BAUDRATEPhilipp Tomsich2017-03-191-2/+0
| | | | | | | | Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini2017-02-031-1/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/ls1046aqds_defconfig configs/ls1046aqds_nand_defconfig configs/ls1046aqds_qspi_defconfig configs/ls1046aqds_sdcard_ifc_defconfig configs/ls1046aqds_sdcard_qspi_defconfig configs/ls1046ardb_emmc_defconfig configs/ls1046ardb_qspi_defconfig configs/ls1046ardb_sdcard_defconfig
| * arch: powerpc: Move CONFIG_FSL_ELBC to KconfigPrabhakar Kushwaha2017-02-031-1/+0
| | | | | | | | | | | | | | Enable ELBC from Kconfig. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | mmc: move CONFIG_GENERIC_MMC to KconfigMasahiro Yamada2017-01-311-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC. Let's create an entry for "config GENERIC_MMC" with "default MMC", then convert all macro defines in headers to Kconfig. Almost all of the defines will go away. I see only two exceptions: configs/blanche_defconfig configs/sandbox_noblk_defconfig They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something might be wrong with these two boards, so should be checked later. Anyway, this is the output of the moveconfig tool. This commit was created as follows: [1] create a config entry in drivers/mmc/Kconfig [2] tools/moveconfig.py -r HEAD GENERIC_MMC [3] manual clean-up of garbage comments in doc/README.* and include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay2017-01-281-6/+0
|/ | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* Convert CONFIG_BOARD_EARLY_INIT_F to KconfigSimon Glass2017-01-251-2/+0
| | | | | | | This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: Simon Glass <sjg@chromium.org>
* ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to KconfigYork Sun2017-01-041-1/+0
| | | | | | | | Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing usage in ls102xa and fsl-layerscape. Remove all powerpc macros in config header and board header files. Signed-off-by: York Sun <york.sun@nxp.com>
* fsl_ddr: Move DDR config options to driver KconfigYork Sun2017-01-041-1/+0
| | | | | | | | | Create driver/ddr/fsl/Kconfig and move existing options. Clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com> [trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: Tom Rini <trini@konsulko.com>
* powerpc: E500: Move CONFIG_E500 and CONFIG_E500MC to KconfigYork Sun2017-01-041-4/+0
| | | | | | Use Kconfig option for E500 and E500MC macros. Signed-off-by: York Sun <york.sun@nxp.com>
View Lorry Controller Status