| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
| |
Solve many compilation warning when stm32prog is activated on the aarch64.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Change the defaut flashlayout location, hardcoded at STM32_DDR_BASE,
to CONFIG_SYS_LOAD_ADDR to avoid issue on board with reserved memory
at STM32_DDR_BASE.
This patch changes the command behavior for STM32MP13 and STM32MP15
platform, as CONFIG_SYS_LOAD_ADDR(0xc2000000) != STM32_DDR_BASE
but without impact for serial boot with STM32CubeProgrammer.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
| |
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Sphinx expects Return: and not @return to indicate a return value.
find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
| |
|
|
|
|
|
|
|
|
| |
Use get_cpu_dev() in uart getID command and remove the defines
DEVICE_ID_BYTE1 and 2 defines.
This patch prepare the support for new SOC family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Handle timeout in stm32prog_serial_get_buffer to sent NACK
to STM32CubeProgrammer when the buffer is not fully received.
This patch avoids to reach the STM32CubeProgrammer timeout and
the associated unrecoverable error.
Timeout error occurred while waiting for acknowledgment.
Error: Write Operation fails at packet number 4165 at address 0x1044FF
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch removes the header check for UART download;
the check of checksum is not mandatory with even parity and chuck
checksum for each 256 received bytes and it is only done for
STM32 image (FSBL = TF-A BL2), not for FIT image.
This patch solve issue of duplicated 0x100 byte written with FIP header.
Fixes: 4fb7b3e10891 ("stm32mp: stm32prog: add FIP header support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support of TF-A FIP header in command stm32prog for all the boot
partition and not only the STM32IMAGE.
This patch is a preliminary patch to support FIP as second boot stage
after TF-A BL2 when CONFIG_TFABOOT is activated for trusted boot chain.
The FIP is archive binary loaded by TF-A BL2, which contains the secure OS
= OP-TEE and the non secure firmware and device tree = U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
| |
The command "stm32prog serial <dev>" can directly use the device sequence
number of serial uclass as this sequence number is egual to alias when it
exist; this assumption simplify the code and avoid access to gd->fdt_blob
and the device tree parsing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove the test on data->dfu_seq, because dfu_seq=0 not only when
the DFU is not started (mask with 0xffff). This flush is mandatory
as the final treatment, common with USB, is done in DFU callback.
This patch avoids issue if the received length is a multiple of
the DFU packet.
For example if size of bootfs partition is egual to 0x4000000,
data->dfu_seq=0 at the end of the partition, the flush it not
requested and the phase is not increased in the callback.
U-Boot continue to request the bootfs in the next GetPhase command.
Fixes: 468f0508b58b ("stm32mp: stm32prog: add serial link support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
| |
|
|
|
|
|
| |
Change debug and pr_ macro to log macro.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
| |
|
|
|
|
|
| |
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
| |
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
Add a support of UART, using the same protocol than MCU STM32.
See "AN5275: USB DFU/USART protocols used in STM32MP1 Series
bootloaders" for details.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
