4 files changed, 0 insertions, 57 deletions
diff --git a/board/engicam/icorem6_rqs/Kconfig b/board/engicam/icorem6_rqs/Kconfig
deleted file mode 100644
index 6dc3a076c4..0000000000
--- a/board/engicam/icorem6_rqs/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_MX6Q_ICORE_RQS
-
-config SYS_BOARD
-	default "icorem6_rqs"
-
-config SYS_VENDOR
-	default "engicam"
-
-config SYS_CONFIG_NAME
-	default "imx6-engicam"
-
-endif
diff --git a/board/engicam/icorem6_rqs/MAINTAINERS b/board/engicam/icorem6_rqs/MAINTAINERS
deleted file mode 100644
index 9a74265eea..0000000000
--- a/board/engicam/icorem6_rqs/MAINTAINERS
+++ /dev/null
@@ -1,9 +0,0 @@
-ICOREM6QDL_RQS BOARD
-M:	Jagan Teki <jagan@amarulasolutions.com>
-S:	Maintained
-F:	board/engicam/icorem6_rqs
-F:	include/configs/imx6-engicam.h
-F:	configs/imx6qdl_icore_rqs_defconfig
-F:	arch/arm/dts/imx6qdl-icore-rqs.dtsi
-F:	arch/arm/dts/imx6q-icore-rqs.dts
-F:	arch/arm/dts/imx6dl-icore-rqs.dts
diff --git a/board/engicam/icorem6_rqs/Makefile b/board/engicam/icorem6_rqs/Makefile
deleted file mode 100644
index 2e3933c698..0000000000
--- a/board/engicam/icorem6_rqs/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-# Copyright (C) 2016 Amarula Solutions B.V.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y  := icorem6_rqs.o
diff --git a/board/engicam/icorem6_rqs/README b/board/engicam/icorem6_rqs/README
deleted file mode 100644
index 97e978cd6f..0000000000
--- a/board/engicam/icorem6_rqs/README
+++ /dev/null
@@ -1,30 +0,0 @@
-How to use U-Boot on Engicam i.CoreM6 RQS Solo/DualLite and Quad/Dual Starter Kit:
-----------------------------------------------------------------------------------
-
-$ make mrproper
-
-- Configure U-Boot for Engicam i.CoreM6 RQS Quad/Dual/Solo/DualLite:
-$ make imx6qdl_icore_rqs_defconfig
-
-- Build U-Boot
-$ make
-
-This will generate the SPL image called SPL and the u-boot-dtb.img.
-
-- Flash the SPL image into the micro SD card:
-
-sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
-
-- Flash the u-boot-dtb.img image into the micro SD card:
-
-sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
-
-- Jumper settings:
-
-MMC Boot: JM3 Closed
-
-- Connect the Serial cable between the Starter Kit and the PC for the console.
-(J28 is the Linux Serial console connector)
-
-- Insert the micro SD card in the board, power it up and U-Boot messages should
-come up.