diff options
-rw-r--r-- | arch/arm/Kconfig | 14 | ||||
-rw-r--r-- | arch/arm/cpu/armv8/Kconfig | 2 | ||||
-rw-r--r-- | arch/arm/dts/Makefile | 3 | ||||
-rw-r--r-- | arch/arm/dts/fsl-lx2160a-rdb.dts | 44 | ||||
-rw-r--r-- | arch/arm/dts/fsl-lx2160a.dtsi | 63 | ||||
-rw-r--r-- | board/freescale/common/qixis.c | 4 | ||||
-rw-r--r-- | board/freescale/lx2160a/Kconfig | 16 | ||||
-rw-r--r-- | board/freescale/lx2160a/MAINTAINERS | 8 | ||||
-rw-r--r-- | board/freescale/lx2160a/Makefile | 9 | ||||
-rw-r--r-- | board/freescale/lx2160a/README | 79 | ||||
-rw-r--r-- | board/freescale/lx2160a/ddr.c | 20 | ||||
-rw-r--r-- | board/freescale/lx2160a/eth_lx2160ardb.c | 210 | ||||
-rw-r--r-- | board/freescale/lx2160a/lx2160a.c | 279 | ||||
-rw-r--r-- | configs/lx2160ardb_tfa_defconfig | 51 | ||||
-rw-r--r-- | include/configs/lx2160a_common.h | 214 | ||||
-rw-r--r-- | include/configs/lx2160ardb.h | 102 |
16 files changed, 1115 insertions, 3 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 455f06cfee..1b9d27e3d1 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1083,6 +1083,19 @@ config TARGET_LS2081ARDB development platform that supports the QorIQ LS2081A/LS2041A Layerscape Architecture processor. +config TARGET_LX2160ARDB + bool "Support lx2160ardb" + select ARCH_LX2160A + select ARCH_MISC_INIT + select ARM64 + select ARMV8_MULTIENTRY + select BOARD_LATE_INIT + help + Support for NXP LX2160ARDB platform. + The lx2160ardb (LX2160A Reference design board (RDB) + is a high-performance development platform that supports the + QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor. + config TARGET_HIKEY bool "Support HiKey 96boards Consumer Edition Platform" select ARM64 @@ -1555,6 +1568,7 @@ source "board/freescale/ls1046ardb/Kconfig" source "board/freescale/ls1012aqds/Kconfig" source "board/freescale/ls1012ardb/Kconfig" source "board/freescale/ls1012afrdm/Kconfig" +source "board/freescale/lx2160a/Kconfig" source "board/freescale/mx35pdk/Kconfig" source "board/freescale/s32v234evb/Kconfig" source "board/grinn/chiliboard/Kconfig" diff --git a/arch/arm/cpu/armv8/Kconfig b/arch/arm/cpu/armv8/Kconfig index 1c12bbde75..cc6d07832d 100644 --- a/arch/arm/cpu/armv8/Kconfig +++ b/arch/arm/cpu/armv8/Kconfig @@ -106,7 +106,7 @@ config PSCI_RESET !TARGET_LS1012AFRWY && \ !TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \ !TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \ - !TARGET_LS2081ARDB && \ + !TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \ !ARCH_UNIPHIER && !TARGET_S32V234EVB help Most armv8 systems have PSCI support enabled in EL3, either through diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index fbc0f8afea..25b56e9efb 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -246,7 +246,8 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-ls2081a-rdb.dtb \ fsl-ls2088a-rdb-qspi.dtb \ fsl-ls1088a-rdb.dtb \ - fsl-ls1088a-qds.dtb + fsl-ls1088a-qds.dtb \ + fsl-lx2160a-rdb.dtb dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb \ diff --git a/arch/arm/dts/fsl-lx2160a-rdb.dts b/arch/arm/dts/fsl-lx2160a-rdb.dts new file mode 100644 index 0000000000..4b526449a1 --- /dev/null +++ b/arch/arm/dts/fsl-lx2160a-rdb.dts @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2160ARDB device tree source + * + * Author: Priyanka Jain <priyanka.jain@nxp.com> + * Sriram Dash <sriram.dash@nxp.com> + * + * Copyright 2018 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2160a.dtsi" + +/ { + model = "NXP Layerscape LX2160ARDB Board"; + compatible = "fsl,lx2160ardb", "fsl,lx2160a"; + +}; + +&esdhc0 { + status = "okay"; +}; + +&esdhc1 { + status = "okay"; +}; + +&sata0 { + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&sata2 { + status = "okay"; +}; + +&sata3 { + status = "okay"; +}; diff --git a/arch/arm/dts/fsl-lx2160a.dtsi b/arch/arm/dts/fsl-lx2160a.dtsi index b407dc6e13..510b070582 100644 --- a/arch/arm/dts/fsl-lx2160a.dtsi +++ b/arch/arm/dts/fsl-lx2160a.dtsi @@ -89,7 +89,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x0 0x2110000 0x0 0x10000>; - interrupts = <0 240 0x4>; /* Level high type */ + interrupts = <0 26 0x4>; /* Level high type */ num-cs = <6>; }; @@ -115,4 +115,65 @@ interrupts = <0 81 0x4>; /* Level high type */ dr_mode = "host"; }; + + esdhc0: esdhc@2140000 { + compatible = "fsl,esdhc"; + reg = <0x0 0x2140000 0x0 0x10000>; + interrupts = <0 28 0x4>; /* Level high type */ + clocks = <&clockgen 4 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + little-endian; + bus-width = <4>; + status = "disabled"; + }; + + esdhc1: esdhc@2150000 { + compatible = "fsl,esdhc"; + reg = <0x0 0x2150000 0x0 0x10000>; + interrupts = <0 63 0x4>; /* Level high type */ + clocks = <&clockgen 4 1>; + voltage-ranges = <1800 1800 3300 3300>; + sdhci,auto-cmd12; + non-removable; + little-endian; + bus-width = <4>; + status = "disabled"; + }; + + sata0: sata@3200000 { + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <0 133 4>; + clocks = <&clockgen 4 3>; + status = "disabled"; + + }; + + sata1: sata@3210000 { + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3210000 0x0 0x10000>; + interrupts = <0 136 4>; + clocks = <&clockgen 4 3>; + status = "disabled"; + + }; + + sata2: sata@3220000 { + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3220000 0x0 0x10000>; + interrupts = <0 97 4>; + clocks = <&clockgen 4 3>; + status = "disabled"; + + }; + + sata3: sata@3230000 { + compatible = "fsl,ls2080a-ahci"; + reg = <0x0 0x3230000 0x0 0x10000>; + interrupts = <0 100 4>; + clocks = <&clockgen 4 3>; + status = "disabled"; + + }; }; diff --git a/board/freescale/common/qixis.c b/board/freescale/common/qixis.c index af3dc59ea1..f1b98bcd2a 100644 --- a/board/freescale/common/qixis.c +++ b/board/freescale/common/qixis.c @@ -227,8 +227,12 @@ static int qixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const ar #ifdef QIXIS_LBMAP_SD QIXIS_WRITE(rst_ctl, 0x30); QIXIS_WRITE(rcfg_ctl, 0); +#ifdef NON_EXTENDED_DUTCFG + QIXIS_WRITE(dutcfg[0], QIXIS_RCW_SRC_SD); +#else set_lbmap(QIXIS_LBMAP_SD); set_rcw_src(QIXIS_RCW_SRC_SD); +#endif QIXIS_WRITE(rcfg_ctl, 0x20); QIXIS_WRITE(rcfg_ctl, 0x21); #else diff --git a/board/freescale/lx2160a/Kconfig b/board/freescale/lx2160a/Kconfig new file mode 100644 index 0000000000..5562c3ec45 --- /dev/null +++ b/board/freescale/lx2160a/Kconfig @@ -0,0 +1,16 @@ +if TARGET_LX2160ARDB + +config SYS_BOARD + default "lx2160a" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "fsl-layerscape" + +config SYS_CONFIG_NAME + default "lx2160ardb" + +source "board/freescale/common/Kconfig" +endif diff --git a/board/freescale/lx2160a/MAINTAINERS b/board/freescale/lx2160a/MAINTAINERS new file mode 100644 index 0000000000..aeb7dbc581 --- /dev/null +++ b/board/freescale/lx2160a/MAINTAINERS @@ -0,0 +1,8 @@ +LX2160ARDB BOARD +M: Priyanka Jain <priyanka.jain@nxp.com> +S: Maintained +F: board/freescale/lx2160a/ +F: include/configs/lx2160a_common.h +F: include/configs/lx2160ardb.h +F: configs/lx2160ardb_tfa_defconfig +F: arch/arm/dts/fsl-lx2160a-rdb.dts diff --git a/board/freescale/lx2160a/Makefile b/board/freescale/lx2160a/Makefile new file mode 100644 index 0000000000..be3709d449 --- /dev/null +++ b/board/freescale/lx2160a/Makefile @@ -0,0 +1,9 @@ +# +# Copyright 2018 Freescale Semiconductor +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += lx2160a.o +obj-y += ddr.o +obj-$(CONFIG_TARGET_LX2160ARDB) += eth_lx2160ardb.o diff --git a/board/freescale/lx2160a/README b/board/freescale/lx2160a/README new file mode 100644 index 0000000000..618c40b6fa --- /dev/null +++ b/board/freescale/lx2160a/README @@ -0,0 +1,79 @@ +Overview +-------- +The LX2160A Reference Design (RDB) is a high-performance computing, +evaluation, and development platform that supports the QorIQ LX2160A +Layerscape Architecture processor and its personalities. + +LX2160A SoC Overview +-------------------------------------- +For details, please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc + +LX2160ARDB board Overview +---------------------- +DDR Memory + Two ports of 72-bits (8-bits ECC) DDR4. + Each port supports four chip-selects and two DIMM + connectors. Data rate upto 3.2 GT/s. + +SERDES ports + Thress serdes controllers (24 lanes) + Serdes1: Supports two USXGMII connectors, each connected through + Aquantia AQR107 phy, two 25GbE SFP+ modules connected through an Inphi + IN112525 phy and one 40 GbE QSFP+ module connected through an Inphi + CS4223 phy. + + Serdes2: Supports one PCIe x4 (Gen1/2/3/4) connector, four SATA 3.0 + connectors + + Serdes3: Supports one PCIe x8 (Gen1/2/3/4) connector + +eSDHC + eSDHC1: Supports a SD connector for connecting SD cards + eSDHC2: Supports 128GB Micron MTFC128GAJAECE-IT eMMC + +Octal SPI (XSPI) + Supports two 64 MB onbpard octal SPI flash memories, one SPI emulator + for off-board emulation + +I2C All system devices on I2C1 multiplexed using PCA9547 multiplexer + Serial Ports + +USB 3.0 + Two high speed USB 3.0 ports. First USB 3.0 port configured as + Host with Type-A connector, second USB 3.0 port configured as OTG + with micro-AB connector + +Serial Ports Two UART ports +Ethernet Two RGMII interfaces +Debug ARM JTAG support + +Booting Options +--------------- +a) Flexspi boot +b) SD boot + +Memory map for Flexspi flash +---------------------------- +Image Flash Offset +bl2_flexspi_nor.pbl (RCW+PBI+bl2.pbl) 0x00000000 +fip.bin (bl31 + bl33(u-boot) + + header for Secure-boot(secure-boot only)) 0x00100000 +Boot firmware Environment 0x00500000 +DDR PHY Firmware (fip_ddr_all.bin) 0x00800000 +DPAA2 MC Firmware 0x00A00000 +DPAA2 DPL 0x00D00000 +DPAA2 DPC 0x00E00000 +Kernel.itb 0x01000000 + +Memory map for sd card +---------------------------- +Image SD card Offset +bl2_sd.pbl (RCW+PBI+bl2.pbl) 0x00008 +fip.bin (bl31 + bl33(u-boot) + + header for Secure-boot(secure-boot only)) 0x00800 +Boot firmware Environment 0x02800 +DDR PHY Firmware (fip_ddr_all.bin) 0x04000 +DPAA2 MC Firmware 0x05000 +DPAA2 DPL 0x06800 +DPAA2 DPC 0x07000 +Kernel.itb 0x08000 diff --git a/board/freescale/lx2160a/ddr.c b/board/freescale/lx2160a/ddr.c new file mode 100644 index 0000000000..cd422bf2bc --- /dev/null +++ b/board/freescale/lx2160a/ddr.c @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + */ + +#include <common.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +DECLARE_GLOBAL_DATA_PTR; + +int fsl_initdram(void) +{ + gd->ram_size = tfa_get_dram_size(); + + if (!gd->ram_size) + gd->ram_size = fsl_ddr_sdram_size(); + + return 0; +} diff --git a/board/freescale/lx2160a/eth_lx2160ardb.c b/board/freescale/lx2160a/eth_lx2160ardb.c new file mode 100644 index 0000000000..365ff73cef --- /dev/null +++ b/board/freescale/lx2160a/eth_lx2160ardb.c @@ -0,0 +1,210 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + * + */ + +#include <common.h> +#include <command.h> +#include <netdev.h> +#include <malloc.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/io.h> +#include <exports.h> +#include <asm/arch/fsl_serdes.h> +#include <fsl-mc/fsl_mc.h> +#include <fsl-mc/ldpaa_wriop.h> + +DECLARE_GLOBAL_DATA_PTR; + +static bool get_inphi_phy_id(struct mii_dev *bus, int addr, int devad) +{ + int phy_reg; + u32 phy_id; + + phy_reg = bus->read(bus, addr, devad, MII_PHYSID1); + phy_id = (phy_reg & 0xffff) << 16; + + phy_reg = bus->read(bus, addr, devad, MII_PHYSID2); + phy_id |= (phy_reg & 0xffff); + + if (phy_id == PHY_UID_IN112525_S03) + return true; + else + return false; +} + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FSL_MC_ENET) + struct memac_mdio_info mdio_info; + struct memac_mdio_controller *reg; + int i, interface; + struct mii_dev *dev; + struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 srds_s1; + + srds_s1 = in_le32(&gur->rcwsr[28]) & + FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK; + srds_s1 >>= FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT; + + reg = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO1; + mdio_info.regs = reg; + mdio_info.name = DEFAULT_WRIOP_MDIO1_NAME; + + /* Register the EMI 1 */ + fm_memac_mdio_init(bis, &mdio_info); + + reg = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO2; + mdio_info.regs = reg; + mdio_info.name = DEFAULT_WRIOP_MDIO2_NAME; + + /* Register the EMI 2 */ + fm_memac_mdio_init(bis, &mdio_info); + + dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME); + switch (srds_s1) { + case 19: + wriop_set_phy_address(WRIOP1_DPMAC2, 0, + CORTINA_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC3, 0, + AQR107_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC4, 0, + AQR107_PHY_ADDR2); + if (get_inphi_phy_id(dev, INPHI_PHY_ADDR1, MDIO_MMD_VEND1)) { + wriop_set_phy_address(WRIOP1_DPMAC5, 0, + INPHI_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC6, 0, + INPHI_PHY_ADDR1); + } + wriop_set_phy_address(WRIOP1_DPMAC17, 0, + RGMII_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC18, 0, + RGMII_PHY_ADDR2); + break; + + case 18: + wriop_set_phy_address(WRIOP1_DPMAC7, 0, + CORTINA_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC8, 0, + CORTINA_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC9, 0, + CORTINA_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC10, 0, + CORTINA_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC3, 0, + AQR107_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC4, 0, + AQR107_PHY_ADDR2); + if (get_inphi_phy_id(dev, INPHI_PHY_ADDR1, MDIO_MMD_VEND1)) { + wriop_set_phy_address(WRIOP1_DPMAC5, 0, + INPHI_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC6, 0, + INPHI_PHY_ADDR1); + } + wriop_set_phy_address(WRIOP1_DPMAC17, 0, + RGMII_PHY_ADDR1); + wriop_set_phy_address(WRIOP1_DPMAC18, 0, + RGMII_PHY_ADDR2); + break; + + default: + printf("SerDes1 protocol 0x%x is not supported on LX2160ARDB\n", + srds_s1); + goto next; + } + + for (i = WRIOP1_DPMAC2; i <= WRIOP1_DPMAC10; i++) { + interface = wriop_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_XGMII: + dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME); + wriop_set_mdio(i, dev); + break; + case PHY_INTERFACE_MODE_25G_AUI: + dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME); + wriop_set_mdio(i, dev); + break; + case PHY_INTERFACE_MODE_XLAUI: + dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME); + wriop_set_mdio(i, dev); + break; + default: + break; + } + } + for (i = WRIOP1_DPMAC17; i <= WRIOP1_DPMAC18; i++) { + interface = wriop_get_enet_if(i); + switch (interface) { + case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME); + wriop_set_mdio(i, dev); + break; + default: + break; + } + } + +next: + cpu_eth_init(bis); +#endif /* CONFIG_FSL_MC_ENET */ + +#ifdef CONFIG_PHY_AQUANTIA + /* + * Export functions to be used by AQ firmware + * upload application + */ + gd->jt->strcpy = strcpy; + gd->jt->mdelay = mdelay; + gd->jt->mdio_get_current_dev = mdio_get_current_dev; + gd->jt->phy_find_by_mask = phy_find_by_mask; + gd->jt->mdio_phydev_for_ethname = mdio_phydev_for_ethname; + gd->jt->miiphy_set_current_dev = miiphy_set_current_dev; +#endif + return pci_eth_init(bis); +} + +#if defined(CONFIG_RESET_PHY_R) +void reset_phy(void) +{ +#if defined(CONFIG_FSL_MC_ENET) + mc_env_boot(); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ + +int fdt_fixup_board_phy(void *fdt) +{ + int mdio_offset; + int ret; + struct mii_dev *dev; + + ret = 0; + + dev = miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME); + if (!get_inphi_phy_id(dev, INPHI_PHY_ADDR1, MDIO_MMD_VEND1)) { + mdio_offset = fdt_path_offset(fdt, "/soc/mdio@0x8B97000"); + + if (mdio_offset < 0) + mdio_offset = fdt_path_offset(fdt, "/mdio@0x8B97000"); + + if (mdio_offset < 0) { + printf("mdio@0x8B9700 node not found in dts\n"); + return mdio_offset; + } + + ret = fdt_setprop_string(fdt, mdio_offset, "status", + "disabled"); + if (ret) { + printf("Could not set disable mdio@0x8B97000 %s\n", + fdt_strerror(ret)); + return ret; + } + } + + return ret; +} diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c new file mode 100644 index 0000000000..a62222e25c --- /dev/null +++ b/board/freescale/lx2160a/lx2160a.c @@ -0,0 +1,279 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + */ + +#include <common.h> +#include <dm.h> +#include <dm/platform_data/serial_pl01x.h> +#include <i2c.h> +#include <malloc.h> +#include <errno.h> +#include <netdev.h> +#include <fsl_ddr.h> +#include <fsl_sec.h> +#include <asm/io.h> +#include <fdt_support.h> +#include <linux/libfdt.h> +#include <fsl-mc/fsl_mc.h> +#include <environment.h> +#include <efi_loader.h> +#include <asm/arch/mmu.h> +#include <hwconfig.h> +#include <asm/arch/fsl_serdes.h> +#include <asm/arch/soc.h> +#include "../common/qixis.h" +#include "../common/vid.h" +#include <fsl_immap.h> + +DECLARE_GLOBAL_DATA_PTR; + +static struct pl01x_serial_platdata serial0 = { +#if CONFIG_CONS_INDEX == 0 + .base = CONFIG_SYS_SERIAL0, +#elif CONFIG_CONS_INDEX == 1 + .base = CONFIG_SYS_SERIAL1, +#else +#error "Unsupported console index value." +#endif + .type = TYPE_PL011, +}; + +U_BOOT_DEVICE(nxp_serial0) = { + .name = "serial_pl01x", + .platdata = &serial0, +}; + +static struct pl01x_serial_platdata serial1 = { + .base = CONFIG_SYS_SERIAL1, + .type = TYPE_PL011, +}; + +U_BOOT_DEVICE(nxp_serial1) = { + .name = "serial_pl01x", + .platdata = &serial1, +}; + +int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +static void uart_get_clock(void) +{ + serial0.clock = get_serial_clock(); + serial1.clock = get_serial_clock(); +} + +int board_early_init_f(void) +{ +#ifdef CONFIG_SYS_I2C_EARLY_INIT + i2c_early_init_f(); +#endif + /* get required clock for UART IP */ + uart_get_clock(); + + fsl_lsch3_early_init_f(); + return 0; +} + +int esdhc_status_fixup(void *blob, const char *compat) +{ + /* Enable both esdhc DT nodes for LX2160ARDB */ + do_fixup_by_compat(blob, compat, "status", "okay", + sizeof("okay"), 1); + + return 0; +} + +#if defined(CONFIG_VID) +int i2c_multiplexer_select_vid_channel(u8 channel) +{ + return select_i2c_ch_pca9547(channel); +} + +#endif + +int checkboard(void) +{ + enum boot_src src = get_boot_src(); + char buf[64]; + u8 sw; + + cpu_name(buf); + printf("Board: %s-RDB, ", buf); + + sw = QIXIS_READ(arch); + printf("Board version: %c, boot from ", (sw & 0xf) - 1 + 'A'); + + if (src == BOOT_SOURCE_SD_MMC) { + puts("SD\n"); + } else { + sw = QIXIS_READ(brdcfg[0]); + sw = (sw >> QIXIS_XMAP_SHIFT) & QIXIS_XMAP_MASK; + switch (sw) { + case 0: + case 4: + puts("FlexSPI DEV#0\n"); + break; + case 1: + puts("FlexSPI DEV#1\n"); + break; + case 2: + case 3: + puts("FlexSPI EMU\n"); + break; + default: + printf("invalid setting, xmap: %d\n", sw); + break; + } + } + printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata)); + + puts("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n"); + puts("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); + puts("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz\n"); + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + return 100000000; +} + +unsigned long get_board_ddr_clk(void) +{ + return 100000000; +} + +int board_init(void) +{ +#ifdef CONFIG_ENV_IS_NOWHERE + gd->env_addr = (ulong)&default_environment[0]; +#endif + + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + +#ifdef CONFIG_FSL_CAAM + sec_init(); +#endif + + return 0; +} + +void detail_board_ddr_info(void) +{ + int i; + u64 ddr_size = 0; + + puts("\nDDR "); + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) + ddr_size += gd->bd->bi_dram[i].size; + print_size(ddr_size, ""); + print_ddr_info(0); +} + +#if defined(CONFIG_ARCH_MISC_INIT) +int arch_misc_init(void) +{ + return 0; +} +#endif + +#ifdef CONFIG_FSL_MC_ENET +extern int fdt_fixup_board_phy(void *fdt); + +void fdt_fixup_board_enet(void *fdt) +{ + int offset; + + offset = fdt_path_offset(fdt, "/soc/fsl-mc"); + + if (offset < 0) + offset = fdt_path_offset(fdt, "/fsl-mc"); + + if (offset < 0) { + printf("%s: fsl-mc node not found in device tree (error %d)\n", + __func__, offset); + return; + } + + if ((get_mc_boot_status() == 0) && (get_dpl_apply_status() == 0)) { + fdt_status_okay(fdt, offset); + fdt_fixup_board_phy(fdt); + } else { + fdt_status_fail(fdt, offset); + } +} + +void board_quiesce_devices(void) +{ + fsl_mc_ldpaa_exit(gd->bd); +} +#endif + +#ifdef CONFIG_OF_BOARD_SETUP + +int ft_board_setup(void *blob, bd_t *bd) +{ + int i; + u64 base[CONFIG_NR_DRAM_BANKS]; + u64 size[CONFIG_NR_DRAM_BANKS]; + + ft_cpu_setup(blob, bd); + + /* fixup DT for the three GPP DDR banks */ + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + base[i] = gd->bd->bi_dram[i].start; + size[i] = gd->bd->bi_dram[i].size; + } + +#ifdef CONFIG_RESV_RAM + /* reduce size if reserved memory is within this bank */ + if (gd->arch.resv_ram >= base[0] && + gd->arch.resv_ram < base[0] + size[0]) + size[0] = gd->arch.resv_ram - base[0]; + else if (gd->arch.resv_ram >= base[1] && + gd->arch.resv_ram < base[1] + size[1]) + size[1] = gd->arch.resv_ram - base[1]; + else if (gd->arch.resv_ram >= base[2] && + gd->arch.resv_ram < base[2] + size[2]) + size[2] = gd->arch.resv_ram - base[2]; +#endif + + fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS); + +#ifdef CONFIG_USB + fsl_fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_FSL_MC_ENET + fdt_fsl_mc_fixup_iommu_map_entry(blob); + fdt_fixup_board_enet(blob); +#endif + + return 0; +} +#endif + +void qixis_dump_switch(void) +{ + int i, nr_of_cfgsw; + + QIXIS_WRITE(cms[0], 0x00); + nr_of_cfgsw = QIXIS_READ(cms[1]); + + puts("DIP switch settings dump:\n"); + for (i = 1; i <= nr_of_cfgsw; i++) { + QIXIS_WRITE(cms[0], i); + printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1])); + } +} diff --git a/configs/lx2160ardb_tfa_defconfig b/configs/lx2160ardb_tfa_defconfig new file mode 100644 index 0000000000..9b63175692 --- /dev/null +++ b/configs/lx2160ardb_tfa_defconfig @@ -0,0 +1,51 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2160ARDB=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_TFABOOT=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2160a-rdb" +CONFIG_ENV_IS_IN_MMC=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_FSL_CAAM=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_ATHEROS=y +CONFIG_PHY_CORTINA=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h new file mode 100644 index 0000000000..41931e5b53 --- /dev/null +++ b/include/configs/lx2160a_common.h @@ -0,0 +1,214 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#ifndef __LX2_COMMON_H +#define __LX2_COMMON_H + +#include <asm/arch/stream_id_lsch3.h> +#include <asm/arch/config.h> +#include <asm/arch/soc.h> + +#define CONFIG_REMAKE_ELF +#define CONFIG_FSL_LAYERSCAPE +#define CONFIG_GICV3 +#define CONFIG_FSL_TZPC_BP147 +#define CONFIG_FSL_MEMAC + +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_FLASH_BASE 0x20000000 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F 1 + +/* DDR */ +#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ +#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL +#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 +#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL +#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 +#define CONFIG_SYS_SDRAM_SIZE 0x200000000UL +#define CONFIG_DDR_SPD +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#define SPD_EEPROM_ADDRESS3 0x53 +#define SPD_EEPROM_ADDRESS4 0x54 +#define SPD_EEPROM_ADDRESS5 0x55 +#define SPD_EEPROM_ADDRESS6 0x56 +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 +#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 2 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 +#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ +#define CONFIG_SYS_MONITOR_LEN (936 * 1024) + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) + +/* SMP Definitinos */ +#define CPU_RELEASE_ADDR secondary_boot_func + +/* Generic Timer Definitions */ +/* + * This is not an accurate number. It is used in start.S. The frequency + * will be udpated later when get_bus_freq(0) is available. + */ + +#define COUNTER_FREQUENCY 25000000 /* 25MHz */ + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) + +/* Serial Port */ +#define CONFIG_PL01X_SERIAL +#define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4) +#define CONFIG_SYS_SERIAL0 0x21c0000 +#define CONFIG_SYS_SERIAL1 0x21d0000 +#define CONFIG_SYS_SERIAL2 0x21e0000 +#define CONFIG_SYS_SERIAL3 0x21f0000 +/*below might needs to be removed*/ +#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ + (void *)CONFIG_SYS_SERIAL1, \ + (void *)CONFIG_SYS_SERIAL2, \ + (void *)CONFIG_SYS_SERIAL3 } +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* MC firmware */ +#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 +#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 +#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 +#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 +#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 + +/* Define phy_reset function to boot the MC based on mcinitcmd. + * This happens late enough to properly fixup u-boot env MAC addresses. + */ +#define CONFIG_RESET_PHY_R + +/* + * Carve out a DDR region which will not be used by u-boot/Linux + * + * It will be used by MC and Debug Server. The MC region must be + * 512MB aligned, so the min size to hide is 512MB. + */ +#ifdef CONFIG_FSL_MC_ENET +#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024) +#endif + +/* I2C bus multiplexer */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ +#define I2C_MUX_CH_DEFAULT 0x8 + +/* RTC */ +#define RTC +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Qixis */ +#define CONFIG_FSL_QIXIS +#define CONFIG_QIXIS_I2C_ACCESS +#define CONFIG_SYS_I2C_FPGA_ADDR 0x66 + +/* PCI */ +#ifdef CONFIG_PCI +#define CONFIG_SYS_PCI_64BIT +#define CONFIG_PCI_SCAN_SHOW +#endif + +/* MMC */ +#ifdef CONFIG_MMC +#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 +#endif + +/* SATA */ + +#ifdef CONFIG_SCSI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 +#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) +#endif + +/* USB */ +#ifdef CONFIG_USB +#define CONFIG_HAS_FSL_XHCI_USB +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#endif + +/* FlexSPI */ +#ifdef CONFIG_NXP_FSPI +#define NXP_FSPI_FLASH_SIZE SZ_64M +#define NXP_FSPI_FLASH_NUM 1 +#endif + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +unsigned long get_board_ddr_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() +#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() +#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4) + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 128 + +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_OFFSET 0x500000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ + CONFIG_ENV_OFFSET) + +/* Allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_SYS_MAXARGS 64 /* max command args */ + +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +/* Initial environment variables */ +#define XSPI_NOR_BOOTCOMMAND "fsl_mc apply dpl 0x20d00000;" \ + "sf probe 0:0;" \ + "sf read 0xa0000000 0x1000000 0x3000000;" \ + "bootm 0xa0000000" + +#define SD_BOOTCOMMAND "mmc read 0xa0000000 0x6800 0xA0;" \ + "fsl_mc apply dpl 0xa0000000;" \ + "mmc read 0xb0000000 0x8000 0x1d000;" \ + "bootm 0xb0000000" + +#define XSPI_MC_INIT_CMD \ + "fsl_mc start mc 0x20a00000 0x20e00000\0" + +#define SD_MC_INIT_CMD \ + "mmc read 0x80000000 0x5000 0x800;" \ + "mmc read 0x80100000 0x7000 0x800;" \ + "fsl_mc start mc 0x80000000 0x80100000\0" + +#endif /* __LX2_COMMON_H */ diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h new file mode 100644 index 0000000000..67d214deb9 --- /dev/null +++ b/include/configs/lx2160ardb.h @@ -0,0 +1,102 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#ifndef __LX2_RDB_H +#define __LX2_RDB_H + +#include "lx2160a_common.h" + +/* Qixis */ +#define QIXIS_XMAP_MASK 0x07 +#define QIXIS_XMAP_SHIFT 5 +#define QIXIS_RST_CTL_RESET_EN 0x30 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x20 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_QSPI 0xff +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SD +#define QIXIS_RCW_SRC_SD 0x08 +#define NON_EXTENDED_DUTCFG + +/* VID */ + +#define I2C_MUX_CH_VOL_MONITOR 0xA +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x63 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 +#define CONFIG_VID_FLS_ENV "lx2160ardb_vdd_mv" +#define CONFIG_VID + +/* The lowest and highest voltage allowed*/ +#define VDD_MV_MIN 775 +#define VDD_MV_MAX 855 + +/* PM Bus commands code for LTC3882*/ +#define PMBUS_CMD_PAGE 0x0 +#define PMBUS_CMD_READ_VOUT 0x8B +#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 +#define PMBUS_CMD_VOUT_COMMAND 0x21 +#define PWM_CHANNEL0 0x0 + +#define CONFIG_VOL_MONITOR_LTC3882_SET +#define CONFIG_VOL_MONITOR_LTC3882_READ + +/* RTC */ +#define CONFIG_SYS_RTC_BUS_NUM 4 + +/* MAC/PHY configuration */ +#if defined(CONFIG_FSL_MC_ENET) +#define CONFIG_MII +#define CONFIG_ETHPRIME "DPMAC1@xgmii" + +#define AQR107_PHY_ADDR1 0x04 +#define AQR107_PHY_ADDR2 0x05 + +#define CORTINA_NO_FW_UPLOAD +#define CORTINA_PHY_ADDR1 0x0 +#define INPHI_PHY_ADDR1 0x0 + +#define RGMII_PHY_ADDR1 0x01 +#define RGMII_PHY_ADDR2 0x02 + +#endif + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:bank_intlv=auto\0" \ + "scriptaddr=0x80800000\0" \ + "kernel_addr_r=0x81000000\0" \ + "pxefile_addr_r=0x81000000\0" \ + "fdt_addr_r=0x88000000\0" \ + "ramdisk_addr_r=0x89000000\0" \ + "loadaddr=0x80100000\0" \ + "kernel_addr=0x100000\0" \ + "ramdisk_addr=0x800000\0" \ + "ramdisk_size=0x2000000\0" \ + "fdt_high=0xa0000000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "kernel_start=0x21000000\0" \ + "lx2160ardb_vdd_mv=800\0" \ + "mcmemsize=0x40000000\0" + +#include <asm/fsl_secure_boot.h> + +#endif /* __LX2_RDB_H */ |