pico-imx6ul: convert ethernet function to DM_ETH

- Remove pinmux definition from pico-imx6ul.c
- Enable NET_RANDOM_ETHADDR for temporary solution, because micrel_ksz8xxx
driver does not support DM_ETH yet, so cannot read MAC address directly.

Before enable DM_ETH:
  Net:   FEC [PRIME]

After enable DM_ETH:
  Net:
  Warning: using random MAC address - ca:3f:43:8f:67:d4
  eth1: ethernet@20b4000

Here is the test commands:
  => dhcp
  BOOTP broadcast 1
  DHCP client bound to address 10.88.88.94 (139 ms)
  *** ERROR: `serverip' not set
  Cannot autoload with TFTPGET
  => ping 8.8.8.8
  Using ethernet@20b4000 device
  host 8.8.8.8 is alive

Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

2 files changed, 2 insertions, 53 deletions

diff --git a/board/technexion/pico-imx6ul/pico-imx6ul.c b/board/technexion/pico-imx6ul/pico-imx6ul.c
index 5d6be26faa..126823fce0 100644
--- a/board/technexion/pico-imx6ul/pico-imx6ul.c
+++ b/board/technexion/pico-imx6ul/pico-imx6ul.c
@@ -18,7 +18,6 @@
 #include <asm/io.h>
 #include <common.h>
 #include <miiphy.h>
-#include <netdev.h>
 #include <linux/delay.h>
 #include <linux/sizes.h>
 #include <usb.h>
@@ -39,61 +38,9 @@ DECLARE_GLOBAL_DATA_PTR;
 #define MDIO_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
 	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
 
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
-	PAD_CTL_SPEED_HIGH   |                                   \
-	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
-
-#define ENET_CLK_PAD_CTRL  (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
-
 #define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
 	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
 
-#define RMII_PHY_RESET IMX_GPIO_NR(1, 28)
-
-static iomux_v3_cfg_t const fec_pads[] = {
-	MX6_PAD_ENET1_TX_EN__ENET2_MDC		| MUX_PAD_CTRL(MDIO_PAD_CTRL),
-	MX6_PAD_ENET1_TX_DATA1__ENET2_MDIO	| MUX_PAD_CTRL(MDIO_PAD_CTRL),
-	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	| MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
-	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_UART4_TX_DATA__GPIO1_IO28	| MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_fec(void)
-{
-	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-int board_eth_init(struct bd_info *bis)
-{
-	setup_iomux_fec();
-
-	gpio_request(RMII_PHY_RESET, "enet_phy_reset");
-	gpio_direction_output(RMII_PHY_RESET, 0);
-	/*
-	 * According to KSZ8081MNX-RNB manual:
-	 * For warm reset, the reset (RST#) pin should be asserted low for a
-	 * minimum of 500μs.  The strap-in pin values are read and updated
-	 * at the de-assertion of reset.
-	 */
-	udelay(500);
-
-	gpio_direction_output(RMII_PHY_RESET, 1);
-	/*
-	 * According to KSZ8081MNX-RNB manual:
-	 * After the de-assertion of reset, wait a minimum of 100μs before
-	 * starting programming on the MIIM (MDC/MDIO) interface.
-	 */
-	udelay(100);
-
-	return fecmxc_initialize(bis);
-}
-
 static int setup_fec(void)
 {
 	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
diff --git a/configs/pico-imx6ul_defconfig b/configs/pico-imx6ul_defconfig
index 79c8d44d99..8ce0fe6ea7 100644
--- a/configs/pico-imx6ul_defconfig
+++ b/configs/pico-imx6ul_defconfig
@@ -44,6 +44,7 @@ CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_DFU_MMC=y
 CONFIG_USB_FUNCTION_FASTBOOT=y
 CONFIG_FASTBOOT_BUF_SIZE=0x10000000
@@ -57,6 +58,7 @@ CONFIG_FSL_USDHC=y
 CONFIG_PHYLIB=y
 CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ8XXX=y
+CONFIG_DM_ETH=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y