summaryrefslogtreecommitdiff
path: root/drivers/hwmon/pmbus/ltc2978.c
Commit message (Collapse)AuthorAgeFilesLines
* hwmon: (pmbus/core) Add min_uV in pmbus regulator helper macroSaravanan Sekar2023-02-031-8/+8
| | | | | | | | | Some regulator operates in a range of voltage which should not allow below the lower threshold. Signed-off-by: Saravanan Sekar <saravanan@linumiz.com> Link: https://lore.kernel.org/r/20221207173716.123223-2-saravanan@linumiz.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) add support for LTC7132Felix Nieuwenhuizen2022-12-041-6/+11
| | | | | | | | | | Add support for LTC7132. The relevant registers in the LTC7132 are identical to the LTC7880. So it's just a matter of adding the chip id. Signed-off-by: Felix Nieuwenhuizen <Felix.Nieuwenhuizen@etas.com> Link: https://lore.kernel.org/r/20221027145135.31802-1-Felix.Nieuwenhuizen@etas.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Set voltage resolutionMårten Lindahl2022-07-131-4/+40
| | | | | | | | | | | | | | | | The LTC2977 regulator does not set the regulator_desc .n_voltages value which is needed in order to let the regulator core list the regulator voltage range. This patch defines a regulator_desc with a voltage range, and uses it for defining voltage resolution for regulators LTC2972/LTC2974/LTC2975/ LTC2977/LTC2978/LTC2979/LTC2980/LTM2987 based on that they all have a 16 bit ADC with the same stepwise 122.07uV resolution. It also scales the resolution to a 1mV resolution which is easier to handle. Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com> Link: https://lore.kernel.org/r/20220614095144.3472305-1-marten.lindahl@axis.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Add chip specific write_byte_dataMårten Lindahl2022-05-201-0/+12
| | | | | | | | | | | | | | | | | | | | | Several of the manuals for devices supported by this driver describes the need for a minimum wait time before the chip is ready to receive next command. This wait time is already implemented in the driver as a ltc_wait_ready function with a driver defined wait time of 100 ms, and is considered for specific devices before reading/writing data on the pmbus. Since this driver uses the default pmbus_regulator_ops for the enable/ disable/is_enabled functions we should add a driver specific callback for write_byte_data to prevent bypassing the wait time recommendations for the following devices: ltc3880/ltc3882/ltc3883/ltc3884/ltc3886/ ltc3887/ltc3889/ltm4664/ltm4675/ltm4676/ltm4677/ltm4678/ltm4680/ltm4686/ ltm4700/ltc7880. Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com> Link: https://lore.kernel.org/r/20220428144039.2464667-4-marten.lindahl@axis.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus) Introduce PMBUS symbol namespaceGuenter Roeck2021-04-201-0/+1
| | | | | | | Exported pmbus symbols are only supposed to be used from PMBus code. Introduce PMBUS symbol namespace to prevent misuse from other code. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus) shrink code and remove pmbus_do_remove()Bartosz Golaszewski2020-12-021-1/+0
| | | | | | | | | | | The only action currently performed in pmbus_do_remove() is removing the debugfs hierarchy. We can schedule a devm action at probe time and remove pmbus_do_remove() entirely from all pmbus drivers. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl [groeck: Removed references to pmbus_do_remove from documentation] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon (pmbus) use simple i2c probe functionStephen Kitt2020-09-231-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | pmbus_do_probe doesn't use the id information provided in its second argument, so this can be removed, which then allows using the single-parameter i2c probe function ("probe_new") for probes. This avoids scanning the identifier tables during probes. Drivers which didn't use the id are converted as-is; drivers which did are modified as follows: * if the information in i2c_client is sufficient, that's used instead (client->name); * configured v. probed comparisons are performed by comparing the configured name to the detected name, instead of the ids; this involves strcmp but is still cheaper than comparing all the device names when scanning the tables; * anything else is handled by calling i2c_match_id() with the same level of error-handling (if any) as before. Additionally, the mismatch message in the ltc2978 driver is adjusted so that it no longer assumes that the driver_data is an index into ltc2978_id. Signed-off-by: Stephen Kitt <steve@sk2.org> Acked-by: Wolfram Sang <wsa@kernel.org> Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus) Add 'phase' parameter where needed for multi-phase supportGuenter Roeck2020-03-081-14/+22
| | | | | | | | | In preparation for multi-phase support, add 'phase' parameter to read_word and set_page functions. Actual multi-phase support will be added in a subsequent patch. Cc: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) add support for more parts.Mike Jones2020-03-081-4/+90
| | | | | | | | | | LTC2972, LTC2979, LTC3884, LTC3889, LTC7880, LTM4664, LTM4677, LTM4678, LTM4680, LTM4700. Signed-off-by: Mike Jones <michael-a1.jones@analog.com> Link: https://lore.kernel.org/r/1581032654-4330-1-git-send-email-michael-a1.jones@analog.com [groeck: Fixed checkpatch issues (long lines, whitespace)] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Fix PMBus polling of MFR_COMMON definitions.Mike Jones2020-02-091-2/+2
| | | | | | | | | | | | | | | Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to bits 6/5. This fixs a LTC297X family bug where polling always returns not busy even when the part is busy. This fixes a LTC388X and LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was not polled, which can lead to NACKing of commands. LTC388X and LTM467X modules now poll BUSY and PEND, increasing reliability by eliminating NACKing of commands. Signed-off-by: Mike Jones <michael-a1.jones@analog.com> Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com Fixes: e04d1ce9bbb49 ("hwmon: (ltc2978) Add polling for chips requiring it") Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157Thomas Gleixner2019-05-301-10/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 3 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [graeme] [gregory] [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema] [hk] [hemahk]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1105 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* hwmon: (ltc2978) Fix spelling mistake "comppatible" -> "compatible"Colin Ian King2018-12-161-1/+1
| | | | | | | There is a spelling mistake in the module description text, fix it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* drivers: hwmon: (pmbus/ltc2978) Add support for LTM4686 uModuleMichael Hennerich2018-10-101-1/+8
| | | | | | | | | | This patch adds support for LTM4686 Ultrathin Dual 10A or Single 20A uModule Regulator with Digital Power System Management. Datasheet: http://www.analog.com/ltm4686 Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add support for LTM4675Guenter Roeck2015-08-191-2/+8
| | | | | | | LTM2975 is a dual 9A or single 18A μModule regulator. It is register compatible with LTM4676. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add polling for chips requiring itMichael Jones2015-08-191-10/+101
| | | | | | | | | Some of the LTC chips supported by this driver have to be polled to ensure that they are ready to accept commands. Signed-off-by: Michael Jones <mike@proclivis.com> [Guenter Roeck: simplifications and formatting changes] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add support for LTC3886Guenter Roeck2015-08-171-2/+22
| | | | | | | | | | LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching regulator controller. It is mostly command compatible to LTC3883, but supports two phases instead of one. Suggested-by: Michael Jones <mike@proclivis.com> Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add support for LTC2980 and LTM2987Guenter Roeck2015-08-171-3/+17
| | | | | | | | | | LTC2980 and LTM2987 are command compatible to LTC2977. They consist of two LTC2977 on a single die, and are instantiated as two separate chips, each supporting eight channels. Suggested-by: Michael Jones <mike@proclivis.com> Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add missing chip IDs for LTC2978 and LTC3882Guenter Roeck2015-08-171-3/+8
| | | | | | | | | | | Add additional chip ID for an older revision of LTC2978, as well as two chip IDs for LTC3882. Turns out the LTC3882 does support the LTC2978_MFR_SPECIAL_ID register, and reading it returns its chip ID, but the register is undocumented. Suggested-by: Michael Jones <mike@proclivis.com> Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Use correct ID mask to detect all chipsGuenter Roeck2015-08-171-22/+17
| | | | | | | | | | Per information from Linear Technologies, the ID mask is 12 bit for all chips of this series. Use this mask to detect chips to ensure that all chip revisions are detected. Suggested-by: Michael Jones <mike@proclivis.com> Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Introduce helper functions for min and max valuesGuenter Roeck2015-08-171-91/+57
| | | | | | | | The code used to determine historic low and high peaks is repeated several times. Introduce helper functions to simplify it. Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Introduce feature flagsGuenter Roeck2015-08-171-12/+18
| | | | | | | | It is becoming cumbersom to track per-chip feature support. Introduce feature flag to simplify the code. Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add support for LTC2975Guenter Roeck2015-08-171-10/+94
| | | | | | | | LTC2975 is mostly compatible to LTC2974, but supports input current and power measurement. Tested-by: Michael Jones <mike@proclivis.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add support for LTC3887Guenter Roeck2015-08-121-5/+14
| | | | | | LTC3887 is an enhanced version of LTC3880 and supports the same commands. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add additional chip IDs for LTM4676 and LTM4676AGuenter Roeck2015-08-121-2/+6
| | | | | | | | | | | | | | | Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed in real systems. In addition to that, chip ID 0x4401 was observed as well. Research shows that the chip ID has been changed from 0x440x to 0x448x in datasheet revision C. Add support for the additional chip ID. Also add the chip ID for LTM4676A, which is functionally identical to LTM4676. Reported-by: Ananda Babu Nettam <anandab@juniper.net> Cc: Ananda Babu Nettam <anandab@juniper.net> Cc: Amit U Jain <amjain@juniper.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add support for LTC3882Guenter Roeck2015-08-121-6/+44
| | | | | | | | LTC3882 is mostly compatible with LTC3880. Major differences are that it does not measure the input current, and it no longer supports LTC's legacy mechanism to identify the chip. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Move code to read chip ID into separate functionGuenter Roeck2015-08-121-19/+29
| | | | | | | | | Verifying the chip type is getting more complicated with new chips, since not all chips support the same mechanism to read the chip type. Move the code into a separate function to simplify adding support for those chips. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) LTM4676 supports CLEAR_PEAKSGuenter Roeck2015-08-091-1/+1
| | | | | | | Use the CLEAR_PEAKS command on LTM4676. Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (ltc2978) Add regulator supportAlan Tull2014-11-301-1/+38
| | | | | | | | | | Add simple on/off regulator support for ltc2978 and other pmbus parts supported by the ltc2978 driver. Signed-off-by: Alan Tull <atull@opensource.altera.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Add support for LTM4676Guenter Roeck2014-03-191-9/+11
| | | | | | | | The chip's programming interface is quite similar to LTC3880 and supports the same set of sensors. Reviewed-by: Robert Coulson <rob.coulson@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Add new chip ID for LTC2974Guenter Roeck2014-03-051-2/+3
| | | | | | | LTC2974 datasheet revision C lists the chip ID for LTC2974 as 0x0213. Reviewed-by: Robert Coulson <rob.coulson@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978): Add support for LTC2978AGuenter Roeck2013-10-181-1/+3
| | | | | | Detect LTC2978A chip ID. Treat it as LC2978. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978): Add support for LTC2977Guenter Roeck2013-10-181-3/+9
| | | | | | LTC2977 is a pin compatible replacement for LTC2978. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Add support for LTC2974 and LTC3883Guenter Roeck2013-04-071-19/+130
| | | | Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Code cleanupGuenter Roeck2013-04-071-11/+14
| | | | | | | | | | Use u16 instead of int to store cached limit attributes. This reduces allocated data size per driver instance by 48 bytes. Use defines for the number of pages supported by individual chips. Use ARRAY_SIZE for loops to initialize array variables, and initialize all variables in the same code block. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus/ltc2978) Fix temperature reportingGuenter Roeck2013-03-141-6/+8
| | | | | | | | | | | | | | On LTC2978, only READ_TEMPERATURE is supported. It reports the internal junction temperature. This register is unpaged. On LTC3880, READ_TEMPERATURE and READ_TEMPERATURE2 are supported. READ_TEMPERATURE is paged and reports external temperatures. READ_TEMPERATURE2 is unpaged and reports the internal junction temperature. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org # 3.2+ Acked-by: Jean Delvare <khali@linux-fr.org>
* hwmon: (pmbus/ltc2978) Use detected chip ID to select supported functionalityGuenter Roeck2013-03-031-1/+1
| | | | | | | | | | We read the chip ID from the chip, use it to determine if the chip ID provided to the driver is correct, and report it if wrong. We should also use the correct chip ID to select supported functionality. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org # 3.2+ Acked-by: Jean Delvare <khali@linux-fr.org>
* hwmon: (pmbus/ltc2978) Fix peak attribute handlingGuenter Roeck2013-03-031-13/+15
| | | | | | | | | | Peak attributes were not initialized and cleared correctly. Also, temp2_max is only supported on page 0 and thus does not need to be an array. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org # 3.2+ Acked-by: Jean Delvare <khali@linux-fr.org>
* hwmon: (pmbus) Simplify remove functionsGuenter Roeck2012-03-181-7/+1
| | | | | | | | | Since devm_kzalloc() is now used to allocate driver memory, the client driver remove function has no purpose other than to call pmbus_do_remove(). This means we can get rid of it by redefining pmbus_do_remove() to use the same prototype, and pointing to it directly. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: (pmbus) Convert pmbus drivers to use devm_kzallocGuenter Roeck2012-03-181-22/+8
| | | | | | Marginally less code and eliminate the possibility of memory leaks. Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* hwmon: convert drivers/hwmon/* to use module_i2c_driver()Axel Lin2012-03-181-11/+1
| | | | | | | | | | | | | | | | | | This patch converts the drivers in drivers/hwmon/* to use the module_i2c_driver() macro which makes the code smaller and a bit simpler. Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Corentin Labbe <corentin.labbe@geomatys.fr> Cc: Dirk Eibach <eibach@gdsys.de> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: Riku Voipio <riku.voipio@iki.fi> Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com> Cc: David George <david.george@ska.ac.za> Cc: "Hans J. Koch" <hjk@hansjkoch.de> Cc: Marc Hulsman <m.hulsman@tudelft.nl> Cc: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* hwmon: (pmbus/ltc2978) Add support for LTC3880 to LTC2978 driverGuenter Roeck2011-10-241-12/+125
| | | | | | | | The LTC3880 PMBus command set is comparable to LTC2978. Add support for it to the LTC2978 driver. Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
* hwmon: (pmbus/ltc2978) Explicit driver for LTC2978Guenter Roeck2011-10-241-0/+295
Provide explicit driver for LTC2978 to enable support for minimum and peak attributes. Remove ltc2978 chip id from generic pmbus driver. Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
View Lorry Controller Status