summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/mmci.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc/host/mmci.c')
-rw-r--r--drivers/mmc/host/mmci.c66
1 files changed, 45 insertions, 21 deletions
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index ec28d175d9c8..150772395cc6 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -33,6 +33,7 @@
#include <linux/amba/mmci.h>
#include <linux/pm_runtime.h>
#include <linux/types.h>
+#include <linux/pinctrl/consumer.h>
#include <asm/div64.h>
#include <asm/io.h>
@@ -654,9 +655,31 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
/* The ST Micro variants has a special bit to enable SDIO */
if (variant->sdio && host->mmc->card)
- if (mmc_card_sdio(host->mmc->card))
+ if (mmc_card_sdio(host->mmc->card)) {
+ /*
+ * The ST Micro variants has a special bit
+ * to enable SDIO.
+ */
+ u32 clk;
+
datactrl |= MCI_ST_DPSM_SDIOEN;
+ /*
+ * The ST Micro variant for SDIO small write transfers
+ * needs to have clock H/W flow control disabled,
+ * otherwise the transfer will not start. The threshold
+ * depends on the rate of MCLK.
+ */
+ if (data->flags & MMC_DATA_WRITE &&
+ (host->size < 8 ||
+ (host->size <= 8 && host->mclk > 50000000)))
+ clk = host->clk_reg & ~variant->clkreg_enable;
+ else
+ clk = host->clk_reg | variant->clkreg_enable;
+
+ mmci_write_clkreg(host, clk);
+ }
+
/*
* Attempt to use DMA operation mode, if this
* should fail, fall back to PIO mode
@@ -840,14 +863,14 @@ static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int rema
if (unlikely(count & 0x3)) {
if (count < 4) {
unsigned char buf[4];
- readsl(base + MMCIFIFO, buf, 1);
+ ioread32_rep(base + MMCIFIFO, buf, 1);
memcpy(ptr, buf, count);
} else {
- readsl(base + MMCIFIFO, ptr, count >> 2);
+ ioread32_rep(base + MMCIFIFO, ptr, count >> 2);
count &= ~0x3;
}
} else {
- readsl(base + MMCIFIFO, ptr, count >> 2);
+ ioread32_rep(base + MMCIFIFO, ptr, count >> 2);
}
ptr += count;
@@ -877,22 +900,6 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem
count = min(remain, maxcnt);
/*
- * The ST Micro variant for SDIO transfer sizes
- * less then 8 bytes should have clock H/W flow
- * control disabled.
- */
- if (variant->sdio &&
- mmc_card_sdio(host->mmc->card)) {
- u32 clk;
- if (count < 8)
- clk = host->clk_reg & ~variant->clkreg_enable;
- else
- clk = host->clk_reg | variant->clkreg_enable;
-
- mmci_write_clkreg(host, clk);
- }
-
- /*
* SDIO especially may want to send something that is
* not divisible by 4 (as opposed to card sectors
* etc), and the FIFO only accept full 32-bit writes.
@@ -900,7 +907,7 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem
* byte become a 32bit write, 7 bytes will be two
* 32bit writes etc.
*/
- writesl(base + MMCIFIFO, ptr, (count + 3) >> 2);
+ iowrite32_rep(base + MMCIFIFO, ptr, (count + 3) >> 2);
ptr += count;
remain -= count;
@@ -1360,6 +1367,23 @@ static int mmci_probe(struct amba_device *dev,
mmc->f_max = min(host->mclk, fmax);
dev_dbg(mmc_dev(mmc), "clocking block at %u Hz\n", mmc->f_max);
+ host->pinctrl = devm_pinctrl_get(&dev->dev);
+ if (IS_ERR(host->pinctrl)) {
+ ret = PTR_ERR(host->pinctrl);
+ goto clk_disable;
+ }
+
+ host->pins_default = pinctrl_lookup_state(host->pinctrl,
+ PINCTRL_STATE_DEFAULT);
+
+ /* enable pins to be muxed in and configured */
+ if (!IS_ERR(host->pins_default)) {
+ ret = pinctrl_select_state(host->pinctrl, host->pins_default);
+ if (ret)
+ dev_warn(&dev->dev, "could not set default pins\n");
+ } else
+ dev_warn(&dev->dev, "could not get default pinstate\n");
+
#ifdef CONFIG_REGULATOR
/* If we're using the regulator framework, try to fetch a regulator */
host->vcc = regulator_get(&dev->dev, "vmmc");