summaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/arm/arch_timer.txt8
-rw-r--r--Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt6
-rw-r--r--Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt36
-rw-r--r--Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt42
-rw-r--r--Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt23
-rw-r--r--Documentation/devicetree/bindings/w1/omap-hdq.txt17
6 files changed, 131 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt
index 37b2cafa4e52..256b4d8bab7b 100644
--- a/Documentation/devicetree/bindings/arm/arch_timer.txt
+++ b/Documentation/devicetree/bindings/arm/arch_timer.txt
@@ -22,6 +22,14 @@ to deliver its interrupts via SPIs.
- always-on : a boolean property. If present, the timer is powered through an
always-on power domain, therefore it never loses context.
+** Optional properties:
+
+- arm,cpu-registers-not-fw-configured : Firmware does not initialize
+ any of the generic timer CPU registers, which contain their
+ architecturally-defined reset values. Only supported for 32-bit
+ systems which follow the ARMv7 architected reset values.
+
+
Example:
timer {
diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
index e2d501d20c9a..1eceefb20f01 100644
--- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
+++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt
@@ -2,7 +2,11 @@ Broadcom GISB bus Arbiter controller
Required properties:
-- compatible: should be "brcm,gisb-arb"
+- compatible:
+ "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips
+ "brcm,bcm7435-gisb-arb" for newer 40nm chips
+ "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips
+ "brcm,bcm7038-gisb-arb" for 130nm chips
- reg: specifies the base physical address and size of the registers
- interrupt-parent: specifies the phandle to the parent interrupt controller
this arbiter gets interrupt line from
diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
new file mode 100644
index 000000000000..f3db93c85eea
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
@@ -0,0 +1,36 @@
+NVIDIA Tegra Memory Controller device tree bindings
+===================================================
+
+Required properties:
+- compatible: Should be "nvidia,tegra<chip>-mc"
+- reg: Physical base address and length of the controller's registers.
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - mc: the module's clock input
+- interrupts: The interrupt outputs from the controller.
+- #iommu-cells: Should be 1. The single cell of the IOMMU specifier defines
+ the SWGROUP of the master.
+
+This device implements an IOMMU that complies with the generic IOMMU binding.
+See ../iommu/iommu.txt for details.
+
+Example:
+--------
+
+ mc: memory-controller@0,70019000 {
+ compatible = "nvidia,tegra124-mc";
+ reg = <0x0 0x70019000 0x0 0x1000>;
+ clocks = <&tegra_car TEGRA124_CLK_MC>;
+ clock-names = "mc";
+
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+
+ #iommu-cells = <1>;
+ };
+
+ sdhci@0,700b0000 {
+ compatible = "nvidia,tegra124-sdhci";
+ ...
+ iommus = <&mc TEGRA_SWGROUP_SDMMC1A>;
+ };
diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt
new file mode 100644
index 000000000000..54ae9f747e45
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt
@@ -0,0 +1,42 @@
+STMicroelectronics STi family Sysconfig Picophy SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in
+the STi family SoC system configuration registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to Documentation/devicetree/bindings/reset/reset.txt
+for common reset controller binding usage.
+
+Required properties:
+- compatible: Should be "st,stih407-picophyreset"
+- #reset-cells: 1, see below
+
+Example:
+
+ picophyreset: picophyreset-controller {
+ compatible = "st,stih407-picophyreset";
+ #reset-cells = <1>;
+ };
+
+Specifying picophyreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the picophyreset device node and an
+index specifying which channel to use, as described in
+Documentation/devicetree/bindings/reset/reset.txt.
+
+Example:
+
+ usb2_picophy0: usbpicophy@0 {
+ resets = <&picophyreset STIH407_PICOPHY0_RESET>;
+ };
+
+Macro definitions for the supported reset channels can be found in:
+include/dt-bindings/reset-controller/stih407-resets.h
diff --git a/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt
new file mode 100644
index 000000000000..6ae79d1843f3
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt
@@ -0,0 +1,23 @@
+Atmel AT91SAM9260 Real Time Timer
+
+Required properties:
+- compatible: should be: "atmel,at91sam9260-rtt"
+- reg: should encode the memory region of the RTT controller
+- interrupts: rtt alarm/event interrupt
+- clocks: should contain the 32 KHz slow clk that will drive the RTT block.
+- atmel,rtt-rtc-time-reg: should encode the GPBR register used to store
+ the time base when the RTT is used as an RTC.
+ The first cell should point to the GPBR node and the second one
+ encode the offset within the GPBR block (or in other words, the
+ GPBR register used to store the time base).
+
+
+Example:
+
+rtt@fffffd20 {
+ compatible = "atmel,at91sam9260-rtt";
+ reg = <0xfffffd20 0x10>;
+ interrupts = <1 4 7>;
+ clocks = <&clk32k>;
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt
new file mode 100644
index 000000000000..fef794741bd1
--- /dev/null
+++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt
@@ -0,0 +1,17 @@
+* OMAP HDQ One wire bus master controller
+
+Required properties:
+- compatible : should be "ti,omap3-1w"
+- reg : Address and length of the register set for the device
+- interrupts : interrupt line.
+- ti,hwmods : "hdq1w"
+
+Example:
+
+- From omap3.dtsi
+ hdqw1w: 1w@480b2000 {
+ compatible = "ti,omap3-1w";
+ reg = <0x480b2000 0x1000>;
+ interrupts = <58>;
+ ti,hwmods = "hdq1w";
+ };