Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

Pull MIPS changes from Paul Burton:
 "Nothing too big or scary in here:

   - Support mremap() for the VDSO, primarily to allow CRIU to restore
     the VDSO to its checkpointed location.

   - Restore the MIPS32 cBPF JIT, after having reverted the enablement
     of the eBPF JIT for MIPS32 systems in the 5.5 cycle.

   - Improve cop0 counter synchronization behaviour whilst onlining CPUs
     by running with interrupts disabled.

   - Better match FPU behaviour when emulating multiply-accumulate
     instructions on pre-r6 systems that implement IEEE754-2008 style
     MACs.

   - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
     to take advantage of instructions introduced by r2.

   - Support for the Ingenic X1000 SoC & the really nice little CU Neo
     development board that's using it.

   - Support for WMAC on GARDENA Smart Gateway devices.

   - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
     preparation for introducing IP35 (Origin 3*) support.

   - Various Kconfig & Makefile cleanups"

* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
  MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
  MIPS: Loongson64: Disable exec hazard
  MIPS: Loongson64: Bump ISA level to MIPSR2
  MIPS: Make DIEI support as a config option
  MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
  MIPS: asm: local: add barriers for Loongson
  MIPS: Loongson64: Select mac2008 only feature
  MIPS: Add MAC2008 Support
  Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
  MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
  MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
  MIPS: generic: don't unconditionally select PINCTRL
  MIPS: don't explicitly select LIBFDT in Kconfig
  MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
  MIPS: SGI-IP30: Check for valid pointer before using it
  MIPS: syscalls: fix indentation of the 'SYSNR' message
  MIPS: boot: fix typo in 'vmlinux.lzma.its' target
  MIPS: fix indentation of the 'RELOCS' message
  dt-bindings: Document loongson vendor-prefix
  MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
  ...

1 files changed, 170 insertions, 0 deletions

diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
new file mode 100644
index 000000000000..03abd94acd84
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "yna,cu1000-neo", "ingenic,x1000";
+	model = "YSH & ATIL General Board CU Neo";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x04000000>;
+	};
+
+	wlan_pwrseq: msc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&lpoclk>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+
+		lpoclk: ap6212a {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+};
+
+&exclk {
+	clock-frequency = <24000000>;
+};
+
+&tcu {
+	/* 1500 kHz for the system timer and clocksource */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+	assigned-clock-rates = <1500000>, <1500000>;
+
+	/* Use channel #0 for the system timer channel #2 for the clocksource */
+	ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c0>;
+
+	ads7830@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+
+	status = "okay";
+};
+
+&mac {
+	phy-mode = "rmii";
+	phy-handle = <&lan8720a>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&msc0 {
+	bus-width = <8>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc0>;
+
+	non-removable;
+
+	status = "okay";
+};
+
+&msc1 {
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc1>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	non-removable;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	status = "okay";
+
+	ap6212a: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpc>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		brcm,drive-strength = <10>;
+	};
+};
+
+&pinctrl {
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-disable;
+	};
+
+	pins_uart2: uart2 {
+		function = "uart2";
+		groups = "uart2-data-d";
+		bias-disable;
+	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
+
+	pins_msc0: msc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
+		bias-disable;
+	};
+
+	pins_msc1: msc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit", "mmc1-4bit";
+		bias-disable;
+	};
+};