summaryrefslogtreecommitdiff
path: root/Documentation/ABI
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2016-12-13 11:35:00 -0800
committerLinus Torvalds <torvalds@linux-foundation.org>2016-12-13 11:35:00 -0800
commit72cca7baf4fba777b8ab770b902cf2e08941773f (patch)
treec5cdbcd65ac166946f54f1dd6ef3693eea29d791 /Documentation/ABI
parent5266e70335dac35c35b5ca9cea4251c1389d4a68 (diff)
parent3e0f9b2ca8e4839335e4d64ec0a75f4fd5111c4b (diff)
downloadlinux-72cca7baf4fba777b8ab770b902cf2e08941773f.tar.gz
Merge tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH: "Here's the "big" staging/iio pull request for 4.10-rc1. Not as big as 4.9 was, but still just over a thousand changes. We almost broke even of lines added vs. removed, as the slicoss driver was removed (got a "clean" driver for the same hardware through the netdev tree), and some iio drivers were also dropped, but I think we ended up adding a few thousand lines to the source tree in the end. Other than that it's a lot of minor fixes all over the place, nothing major stands out at all. All of these have been in linux-next for a while. There will be a merge conflict with Al's vfs tree in the lustre code, but the resolution for that should be pretty simple, that too has been in linux-next" * tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1002 commits) staging: comedi: comedidev.h: Document usage of 'detach' handler staging: fsl-mc: remove unnecessary info prints from bus driver staging: fsl-mc: add sysfs ABI doc staging/lustre/o2iblnd: Fix misspelled attemps->attempts staging/lustre/o2iblnd: Fix misspelling intialized->intialized staging/lustre: Convert all bare unsigned to unsigned int staging/lustre/socklnd: Fix whitespace problem staging/lustre/o2iblnd: Add missing space staging/lustre/lnetselftest: Fix potential integer overflow staging: greybus: audio_module: remove redundant OOM message staging: dgnc: Fix lines longer than 80 characters staging: dgnc: fix blank line after '{' warnings. staging/android: remove Sync Framework tasks from TODO staging/lustre/osc: Revert erroneous list_for_each_entry_safe use staging: slicoss: remove the staging driver staging: lustre: libcfs: remove lnet upcall code staging: lustre: remove set but unused variables staging: lustre: osc: set lock data for readahead lock staging: lustre: import: don't reconnect during connect interpret staging: lustre: clio: remove mtime check in vvp_io_fault_start() ...
Diffstat (limited to 'Documentation/ABI')
-rw-r--r--Documentation/ABI/testing/sysfs-bus-fsl-mc21
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio18
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector36
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8125
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-cros-ec18
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac8
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-light-isl2901819
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-light-tsl258320
-rw-r--r--Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp45318
9 files changed, 273 insertions, 0 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-fsl-mc b/Documentation/ABI/testing/sysfs-bus-fsl-mc
new file mode 100644
index 000000000000..80256b8b4f26
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-fsl-mc
@@ -0,0 +1,21 @@
+What: /sys/bus/fsl-mc/drivers/.../bind
+Date: December 2016
+Contact: stuart.yoder@nxp.com
+Description:
+ Writing a device location to this file will cause
+ the driver to attempt to bind to the device found at
+ this location. The format for the location is Object.Id
+ and is the same as found in /sys/bus/fsl-mc/devices/.
+ For example:
+ # echo dpni.2 > /sys/bus/fsl-mc/drivers/fsl_dpaa2_eth/bind
+
+What: /sys/bus/fsl-mc/drivers/.../unbind
+Date: December 2016
+Contact: stuart.yoder@nxp.com
+Description:
+ Writing a device location to this file will cause the
+ driver to attempt to unbind from the device found at
+ this location. The format for the location is Object.Id
+ and is the same as found in /sys/bus/fsl-mc/devices/.
+ For example:
+ # echo dpni.2 > /sys/bus/fsl-mc/drivers/fsl_dpaa2_eth/unbind
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index fee35c00cc4e..b8f220f978dd 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -329,6 +329,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_pressure_scale
What: /sys/bus/iio/devices/iio:deviceX/in_humidityrelative_scale
What: /sys/bus/iio/devices/iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_scale
What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_scale
KernelVersion: 2.6.35
Contact: linux-iio@vger.kernel.org
Description:
@@ -1579,3 +1580,20 @@ Contact: linux-iio@vger.kernel.org
Description:
Raw (unscaled no offset etc.) electric conductivity reading that
can be processed to siemens per meter.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_raw
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw counter device counts from channel Y. For quadrature
+ counters, multiplication by an available [Y]_scale results in
+ the counts of a single quadrature signal phase from channel Y.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_indexY_raw
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw counter device index value from channel Y. This attribute
+ provides an absolute positional reference (e.g. a pulse once per
+ revolution) which may be used to home positional systems as
+ required.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector b/Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector
new file mode 100644
index 000000000000..2071f9bcfaa5
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-adc-envelope-detector
@@ -0,0 +1,36 @@
+What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_invert
+Date: October 2016
+KernelVersion: 4.9
+Contact: Peter Rosin <peda@axentia.se>
+Description:
+ The DAC is used to find the peak level of an alternating
+ voltage input signal by a binary search using the output
+ of a comparator wired to an interrupt pin. Like so:
+ _
+ | \
+ input +------>-------|+ \
+ | \
+ .-------. | }---.
+ | | | / |
+ | dac|-->--|- / |
+ | | |_/ |
+ | | |
+ | | |
+ | irq|------<-------'
+ | |
+ '-------'
+ The boolean invert attribute (0/1) should be set when the
+ input signal is centered around the maximum value of the
+ dac instead of zero. The envelope detector will search
+ from below in this case and will also invert the result.
+ The edge/level of the interrupt is also switched to its
+ opposite value.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_compare_interval
+Date: October 2016
+KernelVersion: 4.9
+Contact: Peter Rosin <peda@axentia.se>
+Description:
+ Number of milliseconds to wait for the comparator in each
+ step of the binary search for the input peak level. Needs
+ to relate to the frequency of the input signal.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8 b/Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8
new file mode 100644
index 000000000000..ba676520b953
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-counter-104-quad-8
@@ -0,0 +1,125 @@
+What: /sys/bus/iio/devices/iio:deviceX/in_count_count_direction_available
+What: /sys/bus/iio/devices/iio:deviceX/in_count_count_mode_available
+What: /sys/bus/iio/devices/iio:deviceX/in_count_noise_error_available
+What: /sys/bus/iio/devices/iio:deviceX/in_count_quadrature_mode_available
+What: /sys/bus/iio/devices/iio:deviceX/in_index_index_polarity_available
+What: /sys/bus/iio/devices/iio:deviceX/in_index_synchronous_mode_available
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Discrete set of available values for the respective counter
+ configuration are listed in this file.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_count_direction
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Read-only attribute that indicates whether the counter for
+ channel Y is counting up or down.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_count_mode
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Count mode for channel Y. Four count modes are available:
+ normal, range limit, non-recycle, and modulo-n. The preset value
+ for channel Y is used by the count mode where required.
+
+ Normal:
+ Counting is continuous in either direction.
+
+ Range Limit:
+ An upper or lower limit is set, mimicking limit switches
+ in the mechanical counterpart. The upper limit is set to
+ the preset value, while the lower limit is set to 0. The
+ counter freezes at count = preset when counting up, and
+ at count = 0 when counting down. At either of these
+ limits, the counting is resumed only when the count
+ direction is reversed.
+
+ Non-recycle:
+ Counter is disabled whenever a 24-bit count overflow or
+ underflow takes place. The counter is re-enabled when a
+ new count value is loaded to the counter via a preset
+ operation or write to raw.
+
+ Modulo-N:
+ A count boundary is set between 0 and the preset value.
+ The counter is reset to 0 at count = preset when
+ counting up, while the counter is set to the preset
+ value at count = 0 when counting down; the counter does
+ not freeze at the bundary points, but counts
+ continuously throughout.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_noise_error
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Read-only attribute that indicates whether excessive noise is
+ present at the channel Y count inputs in quadrature clock mode;
+ irrelevant in non-quadrature clock mode.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_preset
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ If the counter device supports preset registers, the preset
+ count for channel Y is provided by this attribute.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_quadrature_mode
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Configure channel Y counter for non-quadrature or quadrature
+ clock mode. Selecting non-quadrature clock mode will disable
+ synchronous load mode. In quadrature clock mode, the channel Y
+ scale attribute selects the encoder phase division (scale of 1
+ selects full-cycle, scale of 0.5 selects half-cycle, scale of
+ 0.25 selects quarter-cycle) processed by the channel Y counter.
+
+ Non-quadrature:
+ The filter and decoder circuit are bypassed. Encoder A
+ input serves as the count input and B as the UP/DOWN
+ direction control input, with B = 1 selecting UP Count
+ mode and B = 0 selecting Down Count mode.
+
+ Quadrature:
+ Encoder A and B inputs are digitally filtered and
+ decoded for UP/DN clock.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_set_to_preset_on_index
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Whether to set channel Y counter with channel Y preset value
+ when channel Y index input is active, or continuously count.
+ Valid attribute values are boolean.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_indexY_index_polarity
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Active level of channel Y index input; irrelevant in
+ non-synchronous load mode.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_indexY_synchronous_mode
+KernelVersion: 4.9
+Contact: linux-iio@vger.kernel.org
+Description:
+ Configure channel Y counter for non-synchronous or synchronous
+ load mode. Synchronous load mode cannot be selected in
+ non-quadrature clock mode.
+
+ Non-synchronous:
+ A logic low level is the active level at this index
+ input. The index function (as enabled via
+ set_to_preset_on_index) is performed directly on the
+ active level of the index input.
+
+ Synchronous:
+ Intended for interfacing with encoder Index output in
+ quadrature clock mode. The active level is configured
+ via index_polarity. The index function (as enabled via
+ set_to_preset_on_index) is performed synchronously with
+ the quadrature clock on the active level of the index
+ input.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-cros-ec b/Documentation/ABI/testing/sysfs-bus-iio-cros-ec
new file mode 100644
index 000000000000..297b9720f024
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-cros-ec
@@ -0,0 +1,18 @@
+What: /sys/bus/iio/devices/iio:deviceX/calibrate
+Date: July 2015
+KernelVersion: 4.7
+Contact: linux-iio@vger.kernel.org
+Description:
+ Writing '1' will perform a FOC (Fast Online Calibration). The
+ corresponding calibration offsets can be read from *_calibbias
+ entries.
+
+What: /sys/bus/iio/devices/iio:deviceX/location
+Date: July 2015
+KernelVersion: 4.7
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute returns a string with the physical location where
+ the motion sensor is placed. For example, in a laptop a motion
+ sensor can be located on the base or on the lid. Current valid
+ values are 'base' and 'lid'.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac b/Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac
new file mode 100644
index 000000000000..580e93f373f6
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-dac-dpot-dac
@@ -0,0 +1,8 @@
+What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw_available
+Date: October 2016
+KernelVersion: 4.9
+Contact: Peter Rosin <peda@axentia.se>
+Description:
+ The range of available values represented as the minimum value,
+ the step and the maximum value, all enclosed in square brackets.
+ Example: [0 1 256]
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-light-isl29018 b/Documentation/ABI/testing/sysfs-bus-iio-light-isl29018
new file mode 100644
index 000000000000..f0ce0a0476ea
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-light-isl29018
@@ -0,0 +1,19 @@
+What: /sys/bus/iio/devices/iio:deviceX/proximity_on_chip_ambient_infrared_suppression
+Date: January 2011
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ From ISL29018 Data Sheet (FN6619.4, Oct 8, 2012) regarding the
+ infrared suppression:
+
+ Scheme 0, makes full n (4, 8, 12, 16) bits (unsigned) proximity
+ detection. The range of Scheme 0 proximity count is from 0 to
+ 2^n. Logic 1 of this bit, Scheme 1, makes n-1 (3, 7, 11, 15)
+ bits (2's complementary) proximity_less_ambient detection. The
+ range of Scheme 1 proximity count is from -2^(n-1) to 2^(n-1).
+ The sign bit is extended for resolutions less than 16. While
+ Scheme 0 has wider dynamic range, Scheme 1 proximity detection
+ is less affected by the ambient IR noise variation.
+
+ 0 Sensing IR from LED and ambient
+ 1 Sensing IR from LED with ambient IR rejection
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-light-tsl2583 b/Documentation/ABI/testing/sysfs-bus-iio-light-tsl2583
new file mode 100644
index 000000000000..a2e19964e87e
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-light-tsl2583
@@ -0,0 +1,20 @@
+What: /sys/bus/iio/devices/device[n]/in_illuminance_calibrate
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ This property causes an internal calibration of the als gain trim
+ value which is later used in calculating illuminance in lux.
+
+What: /sys/bus/iio/devices/device[n]/in_illuminance_lux_table
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ This property gets/sets the table of coefficients
+ used in calculating illuminance in lux.
+
+What: /sys/bus/iio/devices/device[n]/in_illuminance_input_target
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ This property is the known externally illuminance (in lux).
+ It is used in the process of calibrating the device accuracy.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp4531 b/Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp4531
new file mode 100644
index 000000000000..2a91fbe394fc
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-potentiometer-mcp4531
@@ -0,0 +1,8 @@
+What: /sys/bus/iio/devices/iio:deviceX/out_resistance_raw_available
+Date: October 2016
+KernelVersion: 4.9
+Contact: Peter Rosin <peda@axentia.se>
+Description:
+ The range of available values represented as the minimum value,
+ the step and the maximum value, all enclosed in square brackets.
+ Example: [0 1 256]