blob: f31087fab2ade2a40c04305c615b636ff86612d7 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
|
/* Copyright (c) 2014 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* USB Power delivery board configuration */
#ifndef __USB_PD_CONFIG_H
#define __USB_PD_CONFIG_H
/* Port and task configuration */
#define PD_PORT_COUNT 1
/* Stub value */
#define TASK_ID_PD 0
#define PORT_TO_TASK_ID(port) TASK_ID_PD
#define TASK_ID_TO_PORT(id) 0
/* Timer selection for baseband PD communication */
#define TIM_CLOCK_PD_TX_C0 14
#define TIM_CLOCK_PD_RX_C0 3
#define TIM_CLOCK_PD_TX(p) TIM_CLOCK_PD_TX_C0
#define TIM_CLOCK_PD_RX(p) TIM_CLOCK_PD_RX_C0
/* Timer channel */
#define TIM_RX_CCR_C0 1
#define TIM_TX_CCR_C0 1
/* RX timer capture/compare register */
#define TIM_CCR_C0 (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_C0, TIM_RX_CCR_C0))
#define TIM_RX_CCR_REG(p) TIM_CCR_C0
/* TX and RX timer register */
#define TIM_REG_TX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_TX_C0))
#define TIM_REG_RX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_RX_C0))
#define TIM_REG_TX(p) TIM_REG_TX_C0
#define TIM_REG_RX(p) TIM_REG_RX_C0
/* use the hardware accelerator for CRC */
#define CONFIG_HW_CRC
/* TX is using SPI1 on PA4-6 */
#define SPI_REGS(p) STM32_SPI1_REGS
static inline void spi_enable_clock(int port)
{
/* Already done in hardware_init() */
}
#define DMAC_SPI_TX(p) STM32_DMAC_CH3
/* RX is on TIM3 CH1 connected to TIM3 CH2 pin (PA7, not internal COMP) */
#define TIM_TX_CCR_IDX(p) TIM_TX_CCR_C0
#define TIM_RX_CCR_IDX(p) TIM_RX_CCR_C0
/* connect TIM3 CH1 to TIM3_CH2 input */
#define TIM_CCR_CS 2
#define EXTI_COMP_MASK(p) (1 << 7)
#define IRQ_COMP STM32_IRQ_EXTI4_15
/* the RX is inverted, triggers on rising edge */
#define EXTI_XTSR STM32_EXTI_RTSR
#define DMAC_TIM_RX(p) STM32_DMAC_CH4
/* the pins used for communication need to be hi-speed */
static inline void pd_set_pins_speed(int port)
{
/* Already done in hardware_init() */
}
/* Reset SPI peripheral used for TX */
static inline void pd_tx_spi_reset(int port)
{
/* Reset SPI1 */
STM32_RCC_APB2RSTR |= (1 << 12);
STM32_RCC_APB2RSTR &= ~(1 << 12);
}
/* Drive the CC line from the TX block */
static inline void pd_tx_enable(int port, int polarity)
{
/* Drive SPI MISO on PA6 by putting it in AF mode */
STM32_GPIO_MODER(GPIO_A) |= 0x2 << (2*6);
/* Drive TX GND on PA4 */
STM32_GPIO_BSRR(GPIO_A) = 1 << (4 + 16 /* Reset */);
}
/* Put the TX driver in Hi-Z state */
static inline void pd_tx_disable(int port, int polarity)
{
/* Put TX GND (PA4) in Hi-Z state */
STM32_GPIO_BSRR(GPIO_A) = 1 << 4 /* Set */;
/* Put SPI MISO (PA6) in Hi-Z by putting it in input mode */
STM32_GPIO_MODER(GPIO_A) &= ~(0x3 << (2*6));
}
/* we know the plug polarity, do the right configuration */
static inline void pd_select_polarity(int port, int polarity)
{
/* captive cable : no polarity */
}
/* Initialize pins used for TX and put them in Hi-Z */
static inline void pd_tx_init(void)
{
/* Already done in hardware_init() */
}
static inline void pd_config_init(int port, uint8_t power_role) {}
static inline int pd_adc_read(int port, int cc)
{
/* only one CC line, assume other one is always high */
return (cc == 0) ? adc_read_channel(ADC_CH_CC1_PD) : 4096;
}
/* 3.0A DFP : no-connect voltage is 2.45V */
#define PD_SRC_VNC (2450 /*mV*/ * 4096 / 3300/* 12-bit ADC with 3.3V range */)
/* we are a power supply, boot as a power source waiting for a sink */
#define PD_DEFAULT_STATE PD_STATE_SRC_DISCONNECTED
/* delay necessary for the voltage transition on the power supply */
#define PD_POWER_SUPPLY_TURN_ON_DELAY 50000 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 50000 /* us */
#endif /* __USB_PD_CONFIG_H */
|
