1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
|
/* Copyright 2016 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Servo V4 configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* 48 MHz SYSCLK clock frequency */
#define CPU_CLOCK 48000000
/* Enable USART1,3,4 and USB streams */
#define CONFIG_STREAM_USART
#define CONFIG_STREAM_USART3
#define CONFIG_STREAM_USART4
#define CONFIG_STREAM_USB
#define CONFIG_CMD_USART_INFO
/* Optional features */
#define CONFIG_STM_HWTIMER32
#define CONFIG_HW_CRC
/* USB Configuration */
#define CONFIG_USB
#define CONFIG_USB_PID 0x501b
#define CONFIG_USB_CONSOLE
#define CONFIG_USB_UPDATE
#define CONFIG_USB_SELF_POWERED
#define CONFIG_USB_SERIALNO
#define DEFAULT_SERIALNO "Uninitialized"
/* USB interface indexes (use define rather than enum to expand them) */
#define USB_IFACE_CONSOLE 0
#define USB_IFACE_GPIO 1
#define USB_IFACE_I2C 2
#define USB_IFACE_USART3_STREAM 3
#define USB_IFACE_USART4_STREAM 4
#define USB_IFACE_UPDATE 5
#define USB_IFACE_COUNT 6
/* USB endpoint indexes (use define rather than enum to expand them) */
#define USB_EP_CONTROL 0
#define USB_EP_CONSOLE 1
#define USB_EP_GPIO 2
#define USB_EP_I2C 3
#define USB_EP_USART3_STREAM 4
#define USB_EP_USART4_STREAM 5
#define USB_EP_UPDATE 6
#define USB_EP_COUNT 7
/* Enable control of GPIOs over USB */
#define CONFIG_USB_GPIO
/* Enable console recasting of GPIO type. */
#define CONFIG_CMD_GPIO_EXTENDED
/* This is not actually an EC so disable some features. */
#undef CONFIG_WATCHDOG_HELP
#undef CONFIG_LID_SWITCH
/* Enable control of I2C over USB */
#define CONFIG_USB_I2C
#define CONFIG_I2C
#define CONFIG_I2C_MASTER
#define I2C_PORT_MASTER 1
/* PD features */
#define CONFIG_ADC
#define CONFIG_BOARD_PRE_INIT
/*
* If task profiling is enabled then the rx falling edge detection interrupts
* can't be processed in time and can't support USB PD messaging.
*/
#undef CONFIG_TASK_PROFILING
#define CONFIG_USB_POWER_DELIVERY
#define CONFIG_USB_PD_DTS
#define CONFIG_USB_PD_DUAL_ROLE
#define CONFIG_USB_PD_DYNAMIC_SRC_CAP
#define CONFIG_USB_PD_INTERNAL_COMP
#define CONFIG_USB_PD_PORT_COUNT 2
#define CONFIG_USB_PD_TCPC
#define CONFIG_USB_PD_TCPM_STUB
#undef CONFIG_USB_PD_PULLUP
#define CONFIG_USB_PD_PULLUP TYPEC_RP_USB
/* Override PD_ROLE_DEFAULT in usb_pd.h */
#define PD_ROLE_DEFAULT(port) ((port) ? PD_ROLE_SOURCE : PD_ROLE_SINK)
/* Variable-current Rp no connect and Ra attach macros */
#define CC_NC(port, cc, sel) (pd_tcpc_cc_nc(port, cc, sel))
#define CC_RA(port, cc, sel) (pd_tcpc_cc_ra(port, cc, sel))
/*
* TODO(crosbug.com/p/60792): The delay values are currently just place holders
* and the delay will need to be relative to the circuitry that allows VBUS to
* be supplied to the DUT port from the CHG port.
*/
#define PD_POWER_SUPPLY_TURN_ON_DELAY 50000 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 50000 /* us */
/* Define typical operating power and max power */
#define PD_OPERATING_POWER_MW 15000
#define PD_MAX_POWER_MW 60000
#define PD_MAX_CURRENT_MA 3000
#define PD_MAX_VOLTAGE_MV 20000
/*
* Allow dangerous commands all the time, since we don't have a write protect
* switch.
*/
#define CONFIG_SYSTEM_UNLOCKED
#ifndef __ASSEMBLER__
/* Timer selection */
#define TIM_CLOCK32 2
#define TIM_ADC 3
#include "gpio_signal.h"
/* USB string indexes */
enum usb_strings {
USB_STR_DESC = 0,
USB_STR_VENDOR,
USB_STR_PRODUCT,
USB_STR_SERIALNO,
USB_STR_VERSION,
USB_STR_I2C_NAME,
USB_STR_CONSOLE_NAME,
USB_STR_USART3_STREAM_NAME,
USB_STR_USART4_STREAM_NAME,
USB_STR_UPDATE_NAME,
USB_STR_COUNT
};
/* ADC signal */
enum adc_channel {
ADC_CHG_CC1_PD = 0,
ADC_CHG_CC2_PD,
ADC_DUT_CC1_PD,
ADC_DUT_CC2_PD,
ADC_SBU1_DET,
ADC_SBU2_DET,
ADC_SUB_C_REF,
/* Number of ADC channels */
ADC_CH_COUNT
};
/**
* Compare cc_voltage to disconnect threshold
*
* This function can be used for boards that support variable Rp settings and
* require a different voltage threshold based on the Rp value attached to a
* given cc line.
*
* @param port USB-C port number
* @param cc_volt voltage measured in mV of the CC line
* @param cc_sel cc1 or cc2 selection
* @return 1 if voltage is >= threshold value for disconnect
*/
int pd_tcpc_cc_nc(int port, int cc_volt, int cc_sel);
/**
* Compare cc_voltage to Ra threshold
*
* This function can be used for boards that support variable Rp settings and
* require a different voltage threshold based on the Rp value attached to a
* given cc line.
*
* @param port USB-C port number
* @param cc_volt voltage measured in mV of the CC line
* @param cc_sel cc1 or cc2 selection
* @return 1 if voltage is < threshold value for Ra attach
*/
int pd_tcpc_cc_ra(int port, int cc_volt, int cc_sel);
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
