1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
|
/* Copyright 2020 The ChromiumOS Authors
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Waddledoo board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
#define VARIANT_DEDEDE_EC_NPCX796FC
#include "baseboard.h"
#undef GPIO_VOLUME_UP_L
#undef GPIO_VOLUME_DOWN_L
#undef CONFIG_VOLUME_BUTTONS
/* EC console commands */
#define CONFIG_CMD_TCPC_DUMP
#define CONFIG_CMD_CHARGER_DUMP
/* Battery */
#define CONFIG_BATTERY_FUEL_GAUGE
/* Charger */
#define CONFIG_CHARGER_RAA489000
#define PD_MAX_VOLTAGE_MV 20000
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_OCPC_DEF_RBATT_MOHMS \
22 /* R_DS(on) 11.6mOhm + 10mOhm sns rstr \
*/
/*
* b/147463641: The charger IC seems to overdraw ~4%, therefore we
* reduce our target accordingly.
*/
#define CONFIG_CHARGER_INPUT_CURRENT_DERATE_PCT 4
#define CONFIG_OCPC
#define CONFIG_CHARGER_PROFILE_OVERRIDE
#define CONFIG_CHARGE_RAMP_HW
#undef CONFIG_CHARGER_SINGLE_CHIP
#define CONFIG_BATTERY_CHECK_CHARGE_TEMP_LIMITS
/*
* GPIO for C1 interrupts, for baseboard use
*
* Note this line might already have its pull up disabled for HDMI DBs, but
* it should be fine to set again before z-state.
*/
#define GPIO_USB_C1_INT_ODL GPIO_SUB_C1_INT_EN_RAILS_ODL
/* Keyboard */
/* LED */
#define CONFIG_LED_COMMON
#define CONFIG_LED_ONOFF_STATES
#define GPIO_BAT_LED_RED_L GPIO_LED_R_ODL
#define GPIO_BAT_LED_GREEN_L GPIO_LED_G_ODL
#define GPIO_PWR_LED_BLUE_L GPIO_LED_B_ODL
/* PWM */
#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */
/* Thermistors */
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
/* USB */
#define CONFIG_BC12_DETECT_PI3USB9201
#define CONFIG_USBC_RETIMER_NB7V904M
#define CONFIG_USB_MUX_RUNTIME_CONFIG
#define CONFIG_USB_MUX_PS8743
/* USB PD */
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_PD_TCPM_RAA489000
#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE
#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (100 * MSEC)
#define CONFIG_USB_PD_COMM_LOCKED
/* USB defines specific to external TCPCs */
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_TCPC_LOW_POWER
/* Variant references the TCPCs to determine Vbus sourcing */
#define CONFIG_USB_PD_5V_EN_CUSTOM
#undef PD_POWER_SUPPLY_TURN_ON_DELAY
#undef PD_POWER_SUPPLY_TURN_OFF_DELAY
#undef CONFIG_USBC_VCONN_SWAP_DELAY_US
/* 20% margin added for these timings */
#define PD_POWER_SUPPLY_TURN_ON_DELAY 13080 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 16080 /* us */
#undef CONFIG_USBC_VCONN_SWAP_DELAY_US
#define CONFIG_USBC_VCONN_SWAP_DELAY_US 787 /* us */
/* USB Type A Features */
#define USB_PORT_COUNT 1
#undef CONFIG_USB_PORT_POWER_SMART_PORT_COUNT
#define CONFIG_USB_PORT_POWER_SMART_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_SMART
#define CONFIG_USB_PORT_POWER_SMART_CDP_SDP_ONLY
#define CONFIG_USB_PORT_POWER_SMART_DEFAULT_MODE USB_CHARGE_MODE_CDP
#define CONFIG_USB_PORT_POWER_SMART_INVERTED
#define GPIO_USB1_ILIM_SEL GPIO_EN_USB_A0_5V_SUB
/* I2C configuration */
#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0
#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0
#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0
#define I2C_PORT_SUB_USB_C1 NPCX_I2C_PORT2_0
#define I2C_PORT_USB_MUX I2C_PORT_USB_C0
/* TODO(b:147440290): Need to handle multiple charger ICs */
#define I2C_PORT_CHARGER I2C_PORT_USB_C0
#define I2C_PORT_ACCEL I2C_PORT_SENSOR
#define I2C_ADDR_EEPROM_FLAGS 0x50 /* 7b address */
/*
* I2C pin names for baseboard
*
* Note: these lines will be set as i2c on start-up, but this should be
* okay since they're ODL.
*/
#define GPIO_EC_I2C_SUB_USB_C1_SCL GPIO_EC_I2C_SUB_C1_SCL_HDMI_EN_ODL
#define GPIO_EC_I2C_SUB_USB_C1_SDA GPIO_EC_I2C_SUB_C1_SDA_HDMI_HPD_ODL
#define CONFIG_MATH_UTIL
/*
* There is ccd connection issue on board id = 2.
* NB7V904M is needed to be active to resolve this.
*/
#define CONFIG_NB7V904M_LPM_OVERRIDE
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum chg_id {
CHARGER_PRIMARY,
CHARGER_SECONDARY,
CHARGER_NUM,
};
enum temp_sensor_id { TEMP_SENSOR_1, TEMP_SENSOR_2, TEMP_SENSOR_COUNT };
enum adc_channel {
ADC_TEMP_SENSOR_1, /* ADC0 */
ADC_TEMP_SENSOR_2, /* ADC1 */
ADC_SUB_ANALOG, /* ADC2 */
ADC_VSNS_PP3300_A, /* ADC9 */
ADC_CH_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_SDI,
BATTERY_SWD,
BATTERY_TYPE_COUNT,
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
