1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
|
/* Copyright 2019 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Kohaku board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Baseboard features */
#include "baseboard.h"
/* Optional features */
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */
#define CONFIG_POWER_BUTTON
#define CONFIG_KEYBOARD_BOARD_CONFIG
#define CONFIG_KEYBOARD_PROTOCOL_8042
#define CONFIG_LED_COMMON
#define CONFIG_LOW_POWER_IDLE
#define CONFIG_HOSTCMD_ESPI
/* #define CONFIG_HOSTCMD_ESPI_VW_SIGNALS */
#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096
/* Keyboard features */
#define CONFIG_PWM_KBLIGHT
/* Sensors */
/* BMI160 Base accel/gyro */
#define CONFIG_ACCEL_INTERRUPTS
#define CONFIG_ACCELGYRO_BMI160
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define CONFIG_ACCELGYRO_BMI160_INT2_OUTPUT
/* BMA253 Lid accel */
#define CONFIG_ACCEL_BMA255
#define CONFIG_ACCEL_FORCE_MODE_MASK (BIT(LID_ACCEL) | BIT(LID_ALS))
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_LID_ANGLE_UPDATE
/* OPT3001 ALS */
#define CONFIG_ALS
#define ALS_COUNT 1
#define CONFIG_ALS_OPT3001
#define OPT3001_I2C_ADDR OPT3001_I2C_ADDR1
/* USB Type C and USB PD defines */
#define CONFIG_USB_PD_TCPM_PS8751
#define BOARD_TCPC_C0_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
#define BOARD_TCPC_C0_RESET_POST_DELAY 0
#define BOARD_TCPC_C1_RESET_HOLD_DELAY PS8XXX_RESET_DELAY_MS
#define BOARD_TCPC_C1_RESET_POST_DELAY 0
/* Volume Button feature */
#define CONFIG_VOLUME_BUTTONS
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
/* Thermal features */
#define CONFIG_TEMP_SENSOR_POWER_GPIO GPIO_EN_A_RAILS
#define CONFIG_THERMISTOR
#define CONFIG_THROTTLE_AP
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
/* MST */
/*
* TDOD (b/124068003): This inherently assumes the MST chip is connected to only
* one Type C port. This will need to be chagned to support 2 Type C ports
* connected to the same MST chip.
*/
#define USB_PD_PORT_TCPC 1
/*
* Macros for GPIO signals used in common code that don't match the
* schematic names. Signal names in gpio.inc match the schematic and are
* then redefined here to so it's more clear which signal is being used for
* which purpose.
*/
#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_L
#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_L
#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
#define GPIO_PCH_SLP_S4_L GPIO_SLP_S4_L
#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
/* GPIO signals updated base on board version. */
#define GPIO_EN_PP5000_A gpio_en_pp5000_a
extern enum gpio_signal gpio_en_pp5000_a;
enum adc_channel {
ADC_TEMP_SENSOR_1, /* ADC0 */
ADC_TEMP_SENSOR_2, /* ADC1 */
ADC_CH_COUNT
};
enum sensor_id {
LID_ACCEL = 0,
BASE_ACCEL,
BASE_GYRO,
LID_ALS,
SENSOR_COUNT,
};
enum pwm_channel {
PWM_CH_KBLIGHT,
PWM_CH_COUNT
};
enum temp_sensor_id {
TEMP_SENSOR_1,
TEMP_SENSOR_2,
TEMP_SENSOR_COUNT
};
/* List of possible batteries */
enum battery_type {
BATTERY_SMP_LIS,
BATTERY_SMP_SDI,
BATTERY_TYPE_COUNT,
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
