1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
|
/* Copyright 2015 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* USB Power delivery board configuration */
#ifndef __USB_PD_CONFIG_H
#define __USB_PD_CONFIG_H
/* Port and task configuration */
#define PD_PORT_COUNT 1
#define PORT_TO_TASK_ID(port) TASK_ID_PD
#define TASK_ID_TO_PORT(id) 0
/* Timer selection for baseband PD communication */
#define TIM_CLOCK_PD_TX_C0 17
#define TIM_CLOCK_PD_RX_C0 1
#define TIM_CLOCK_PD_TX(p) TIM_CLOCK_PD_TX_C0
#define TIM_CLOCK_PD_RX(p) TIM_CLOCK_PD_RX_C0
/* Timer channel */
#define TIM_RX_CCR_C0 1
#define TIM_TX_CCR_C0 1
/* RX timer capture/compare register */
#define TIM_CCR_C0 (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_C0, TIM_RX_CCR_C0))
#define TIM_RX_CCR_REG(p) TIM_CCR_C0
/* TX and RX timer register */
#define TIM_REG_TX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_TX_C0))
#define TIM_REG_RX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_RX_C0))
#define TIM_REG_TX(p) TIM_REG_TX_C0
#define TIM_REG_RX(p) TIM_REG_RX_C0
/* use the hardware accelerator for CRC */
#define CONFIG_HW_CRC
/* TX is using SPI1 on PB4 */
#define SPI_REGS(p) STM32_SPI1_REGS
static inline void spi_enable_clock(int port)
{
STM32_RCC_APB2ENR |= STM32_RCC_PB2_SPI1;
}
/* SPI1_TX no remap needed */
#define DMAC_SPI_TX(p) STM32_DMAC_CH3
/* RX is using COMP1 triggering TIM1 CH1 */
#define CMP1OUTSEL STM32_COMP_CMP1OUTSEL_TIM1_IC1
#define CMP2OUTSEL 0
#define TIM_TX_CCR_IDX(p) TIM_TX_CCR_C0
#define TIM_RX_CCR_IDX(p) TIM_RX_CCR_C0
#define TIM_CCR_CS 1
#define EXTI_COMP_MASK(p) (1 << 21)
#define IRQ_COMP STM32_IRQ_COMP
/* triggers packet detection on comparator falling edge */
#define EXTI_XTSR STM32_EXTI_FTSR
#define DMAC_TIM_RX(p) STM32_DMAC_CH2
/* the pins used for communication need to be hi-speed */
static inline void pd_set_pins_speed(int port)
{
/* 40 Mhz pin speed on TX_EN (PA15) */
STM32_GPIO_OSPEEDR(GPIO_A) |= 0xC0000000;
/* 40 MHz pin speed on SPI CLK/MOSI (PB3/4) TIM17_CH1 (PB9) */
STM32_GPIO_OSPEEDR(GPIO_B) |= 0x000C03C0;
}
/* Reset SPI peripheral used for TX */
static inline void pd_tx_spi_reset(int port)
{
/* Reset SPI1 */
STM32_RCC_APB1RSTR |= (1 << 12);
STM32_RCC_APB1RSTR &= ~(1 << 12);
}
/* Drive the CC line from the TX block */
static inline void pd_tx_enable(int port, int polarity)
{
/* PB4 is SPI1_MISO */
gpio_set_alternate_function(GPIO_B, 0x0010, 0);
gpio_set_level(GPIO_PD_TX_EN, 1);
}
/* Put the TX driver in Hi-Z state */
static inline void pd_tx_disable(int port, int polarity)
{
/* TX_DATA on PB4 is an output low GPIO to disable the FET */
STM32_GPIO_MODER(GPIO_B) = (STM32_GPIO_MODER(GPIO_B) & ~(3 << (2*4)))
| (1 << (2*4));
/*
* Tri-state the low side after the high side
* to ensure we are not going above Vnc
*/
gpio_set_level(GPIO_PD_TX_EN, 0);
}
/* we know the plug polarity, do the right configuration */
static inline void pd_select_polarity(int port, int polarity)
{
/*
* use the right comparator : CC1 -> PA1 (COMP1 INP)
* use VrefInt / 2 as INM (about 600mV)
*/
STM32_COMP_CSR = (STM32_COMP_CSR & ~STM32_COMP_CMP1INSEL_MASK)
| STM32_COMP_CMP1EN | STM32_COMP_CMP1INSEL_VREF12;
}
/* Initialize pins used for TX and put them in Hi-Z */
static inline void pd_tx_init(void)
{
gpio_config_module(MODULE_USB_PD, 1);
}
static inline void pd_set_host_mode(int port, int enable)
{
if (!enable)
gpio_set_level(GPIO_PPVAR_VBUS_EN, 0);
}
static inline void pd_config_init(int port, uint8_t power_role)
{
/* Initialize TX pins and put them in Hi-Z */
pd_tx_init();
}
static inline int pd_adc_read(int port, int cc)
{
/* only one CC line, assume other one is always low */
return (cc == 0) ? adc_read_channel(ADC_CH_CC1_PD) : 0;
}
static inline void pd_set_vconn(int port, int polarity, int enable)
{
}
static inline int pd_snk_is_vbus_provided(int port)
{
return 0;
}
/* Standard-current DFP : no-connect voltage is 1.55V */
#define PD_SRC_VNC 1550 /* mV */
/* UFP-side : threshold for DFP connection detection */
#define PD_SNK_VA 200 /* mV */
/* we are acting only as a source */
#define PD_DEFAULT_STATE PD_STATE_SRC_DISCONNECTED
/* delay necessary for the voltage transition on the power supply */
/* TODO (code.google.com/p/chrome-os-partner/issues/detail?id=37078)
* Need to measure these and adjust for honeybuns.
*/
#define PD_POWER_SUPPLY_TURN_ON_DELAY 50000 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 50000 /* us */
/* Define typical operating power and max power */
#define PD_OPERATING_POWER_MW 1000
#define PD_MAX_POWER_MW 60000
#define PD_MAX_CURRENT_MA 3000
#define PD_MAX_VOLTAGE_MV 20000
#endif /* __USB_PD_CONFIG_H */
|
