blob: 4abb3e8d51c6853abd0e34a64c3ffb6e652b16ae (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
/* Copyright (c) 2014 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* USB Power delivery board configuration */
#ifndef __USB_PD_CONFIG_H
#define __USB_PD_CONFIG_H
/* Port and task configuration */
#define PD_PORT_COUNT 1
#define PORT_TO_TASK_ID(port) TASK_ID_PD
#define TASK_ID_TO_PORT(id) 0
/* Timer selection for baseband PD communication */
#define TIM_CLOCK_PD_TX_C0 17
#define TIM_CLOCK_PD_RX_C0 1
#define TIM_CLOCK_PD_TX(p) TIM_CLOCK_PD_TX_C0
#define TIM_CLOCK_PD_RX(p) TIM_CLOCK_PD_RX_C0
/* Timer channel */
#define TIM_RX_CCR_C0 1
/* RX timer capture/compare register */
#define TIM_CCR_C0 (&STM32_TIM_CCRx(TIM_CLOCK_PD_RX_C0, TIM_RX_CCR_C0))
#define TIM_RX_CCR_REG(p) TIM_CCR_C0
/* TX and RX timer register */
#define TIM_REG_TX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_TX_C0))
#define TIM_REG_RX_C0 (STM32_TIM_BASE(TIM_CLOCK_PD_RX_C0))
#define TIM_REG_TX(p) TIM_REG_TX_C0
#define TIM_REG_RX(p) TIM_REG_RX_C0
/* use the hardware accelerator for CRC */
#define CONFIG_HW_CRC
/* TX is using SPI1 on PB3-4 */
#define SPI_REGS(p) STM32_SPI1_REGS
static inline void spi_enable_clock(int port)
{
STM32_RCC_APB2ENR |= STM32_RCC_PB2_SPI1;
}
/* SPI1_TX no remap needed */
#define DMAC_SPI_TX(p) STM32_DMAC_CH3
/* RX is using COMP1 triggering TIM1 CH1 */
#define CMP1OUTSEL STM32_COMP_CMP1OUTSEL_TIM1_IC1
#define CMP2OUTSEL 0
#define TIM_CCR_IDX(p) TIM_RX_CCR_C0
#define TIM_CCR_CS 1
#define EXTI_COMP_MASK(p) (1 << 21)
#define IRQ_COMP STM32_IRQ_COMP
/* triggers packet detection on comparator falling edge */
#define EXTI_XTSR STM32_EXTI_FTSR
/* TIM1_CH1 no remap needed */
#define DMAC_TIM_RX(p) STM32_DMAC_CH2
/* the pins used for communication need to be hi-speed */
static inline void pd_set_pins_speed(int port)
{
/* 40 Mhz pin speed on TX_EN (PA15) */
STM32_GPIO_OSPEEDR(GPIO_A) |= 0xC0000000;
/* 40 MHz pin speed on SPI CLK/MOSI (PB3/4) TIM17_CH1 (PB9) */
STM32_GPIO_OSPEEDR(GPIO_B) |= 0x000C03C0;
}
/* Reset SPI peripheral used for TX */
static inline void pd_tx_spi_reset(int port)
{
/* Reset SPI1 */
STM32_RCC_APB2RSTR |= (1 << 12);
STM32_RCC_APB2RSTR &= ~(1 << 12);
}
/* Drive the CC line from the TX block */
static inline void pd_tx_enable(int port, int polarity)
{
/* PB4 is SPI1_MISO */
gpio_set_alternate_function(GPIO_B, 0x0010, 0);
gpio_set_level(GPIO_PD_CC1_TX_EN, 1);
}
/* Put the TX driver in Hi-Z state */
static inline void pd_tx_disable(int port, int polarity)
{
/* output low on SPI TX (PB4) to disable the FET */
STM32_GPIO_MODER(GPIO_B) = (STM32_GPIO_MODER(GPIO_B)
& ~(3 << (2*4)))
| (1 << (2*4));
/* put the low level reference in Hi-Z */
gpio_set_level(GPIO_PD_CC1_TX_EN, 0);
}
static inline void pd_select_polarity(int port, int polarity)
{
/*
* use the right comparator : CC1 -> PA1 (COMP1 INP)
* use VrefInt / 2 as INM (about 600mV)
*/
STM32_COMP_CSR = (STM32_COMP_CSR & ~STM32_COMP_CMP1INSEL_MASK)
| STM32_COMP_CMP1EN | STM32_COMP_CMP1INSEL_VREF12;
}
/* Initialize pins used for TX and put them in Hi-Z */
static inline void pd_tx_init(void)
{
gpio_config_module(MODULE_USB_PD, 1);
}
static inline void pd_set_host_mode(int port, int enable) {}
static inline int pd_adc_read(int port, int cc)
{
return adc_read_channel(ADC_CH_CC1_PD);
}
static inline int pd_snk_is_vbus_provided(int port)
{
return 1;
}
/* 3.0A DFP : no-connect voltage is 2.45V */
#define PD_SRC_VNC 2450 /* mV */
/* UFP-side : threshold for DFP connection detection */
#define PD_SNK_VA 250 /* mV */
/* we are acting only as a sink */
#define PD_DEFAULT_STATE PD_STATE_SNK_DISCONNECTED
/* delay necessary for the voltage transition on the power supply */
#define PD_POWER_SUPPLY_TRANSITION_DELAY 50000 /* us */
#endif /* __USB_PD_CONFIG_H */
|
