1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
/* Copyright 2018 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "charge_manager.h"
#include "console.h"
#include "gpio.h"
#include "system.h"
#include "usb_mux.h"
#include "usbc_ppc.h"
#include "util.h"
#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args)
#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args)
int pd_check_vconn_swap(int port)
{
/* TODO(waihong): Check any case we do not allow. */
return 1;
}
__override void pd_execute_data_swap(int port, int data_role)
{
/* Do nothing */
}
static uint8_t vbus_en[CONFIG_USB_PD_PORT_COUNT];
static uint8_t vbus_rp[CONFIG_USB_PD_PORT_COUNT] = {TYPEC_RP_1A5, TYPEC_RP_1A5};
static void board_vbus_update_source_current(int port)
{
if (port == 0) {
/*
* Port 0 is controlled by a USB-C PPC SN5S330.
*/
ppc_set_vbus_source_current_limit(port, vbus_rp[port]);
ppc_vbus_source_enable(port, vbus_en[port]);
} else if (port == 1) {
/*
* Port 1 is controlled by a USB-C current-limited power
* switch, NX5P3290. Change the GPIO driving the load switch.
*
* 1.5 vs 3.0 A limit is controlled by a dedicated gpio.
* If the GPIO is asserted, it shorts a n-MOSFET to put a
* 16.5k resistance (2x 33k in parallel) on the NX5P3290 load
* switch ILIM pin, setting a minimum OCP current of 3100 mA.
* If the GPIO is deasserted, the n-MOSFET is open that makes
* a single 33k resistor on ILIM, setting a minimum OCP
* current of 1505 mA.
*/
gpio_set_level(GPIO_EN_USB_C1_3A,
vbus_rp[port] == TYPEC_RP_3A0 ? 1 : 0);
gpio_set_level(GPIO_EN_USB_C1_5V_OUT, vbus_en[port]);
}
}
void pd_power_supply_reset(int port)
{
int prev_en;
prev_en = vbus_en[port];
/* Disable VBUS */
vbus_en[port] = 0;
board_vbus_update_source_current(port);
/* Enable discharge if we were previously sourcing 5V */
if (prev_en)
pd_set_vbus_discharge(port, 1);
#ifdef CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT
/* Give back the current quota we are no longer using */
charge_manager_source_port(port, 0);
#endif /* defined(CONFIG_USB_PD_MAX_SINGLE_SOURCE_CURRENT) */
/* notify host of power info change */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
}
int pd_set_power_supply_ready(int port)
{
/* Disable charging */
board_vbus_sink_enable(port, 0);
pd_set_vbus_discharge(port, 0);
/* Provide VBUS */
vbus_en[port] = 1;
board_vbus_update_source_current(port);
/* Ensure we advertise the proper available current quota */
charge_manager_source_port(port, 1);
/* notify host of power info change */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
return EC_SUCCESS; /* we are ready */
}
int board_vbus_source_enabled(int port)
{
return vbus_en[port];
}
__override void typec_set_source_current_limit(int port, enum tcpc_rp_value rp)
{
vbus_rp[port] = rp;
board_vbus_update_source_current(port);
}
int pd_snk_is_vbus_provided(int port)
{
return !gpio_get_level(port ? GPIO_USB_C1_VBUS_DET_L :
GPIO_USB_C0_VBUS_DET_L);
}
/* ----------------- Vendor Defined Messages ------------------ */
extern uint32_t dp_status[CONFIG_USB_PD_PORT_COUNT];
__override int svdm_dp_attention(int port, uint32_t *payload)
{
int lvl = PD_VDO_DPSTS_HPD_LVL(payload[1]);
int irq = PD_VDO_DPSTS_HPD_IRQ(payload[1]);
const struct usb_mux *mux = &usb_muxes[port];
dp_status[port] = payload[1];
if (!(dp_flags[port] & DP_FLAGS_DP_ON)) {
if (lvl)
dp_flags[port] |= DP_FLAGS_HPD_HI_PENDING;
return 1;
}
mux->hpd_update(port, lvl, irq);
/* ack */
return 1;
}
|
