1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
|
/* Copyright 2021 The ChromiumOS Authors
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Waddledoo board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
#define VARIANT_DEDEDE_EC_NPCX796FC
#include "baseboard.h"
#undef CONFIG_I2C_DEBUG
/*
* The RAM and flash size combination on the the NPCX797FC does not leave
* any unused flash space that can be used to store the .init_rom section.
*/
#undef CONFIG_CHIP_INIT_ROM_REGION
/* Save some flash space */
#define CONFIG_DEBUG_ASSERT_BRIEF
#undef CONFIG_CMD_ACCELSPOOF
#undef CONFIG_CMD_BATTFAKE
/* EC console commands */
#define CONFIG_CMD_TCPC_DUMP
#define CONFIG_CMD_CHARGER_DUMP
/* Battery */
#define CONFIG_BATTERY_FUEL_GAUGE
/* Charger */
#define CONFIG_CHARGER_RAA489000
#define PD_MAX_VOLTAGE_MV 20000
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10
#define CONFIG_CHARGER_SENSE_RESISTOR 10
#define CONFIG_OCPC_DEF_RBATT_MOHMS \
22 /* R_DS(on) 11.6mOhm + 10mOhm sns rstr \
*/
#define CONFIG_OCPC
#define CONFIG_CHARGE_RAMP_HW
#undef CONFIG_CHARGER_SINGLE_CHIP
#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE
#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (100 * MSEC)
/*
* b/147463641: The charger IC seems to overdraw ~4%, therefore we
* reduce our target accordingly.
*/
#define CONFIG_CHARGER_INPUT_CURRENT_DERATE_PCT 4
#define CONFIG_BATTERY_CHECK_CHARGE_TEMP_LIMITS
#define CONFIG_CHARGER_PROFILE_OVERRIDE
/*
* GPIO for C1 interrupts, for baseboard use
*
* Note this line might already have its pull up disabled for HDMI DBs, but
* it should be fine to set again before z-state.
*/
#define GPIO_USB_C1_INT_ODL GPIO_SUB_C1_INT_EN_RAILS_ODL
/* Keyboard */
/* LED */
#define CONFIG_LED_COMMON
#define CONFIG_LED_ONOFF_STATES
#define GPIO_BAT_LED_RED_L GPIO_LED_R_ODL
#define GPIO_BAT_LED_GREEN_L GPIO_LED_G_ODL
#define GPIO_PWR_LED_BLUE_L GPIO_LED_B_ODL
/* PWM */
#define NPCX7_PWM1_SEL 0 /* GPIO C2 is not used as PWM1. */
/* Thermistors */
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
/* USB */
#define CONFIG_BC12_DETECT_PI3USB9201
#define CONFIG_USB_MUX_PS8743
/* USB PD */
#define CONFIG_USB_PD_PORT_MAX_COUNT 2
#define CONFIG_USB_PD_TCPM_RAA489000
#undef CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE
#define CONFIG_USB_PD_TCPC_LPM_EXIT_DEBOUNCE (100 * MSEC)
#define CONFIG_USB_PD_COMM_LOCKED
/* USB defines specific to external TCPCs */
#define CONFIG_USB_PD_DUAL_ROLE_AUTO_TOGGLE
#define CONFIG_USB_PD_VBUS_DETECT_TCPC
#define CONFIG_USB_PD_DISCHARGE_TCPC
#define CONFIG_USB_PD_TCPC_LOW_POWER
/* USB Type A Features */
#define USB_PORT_COUNT 1
#define CONFIG_USB_PORT_POWER_DUMB
/* Variant references the TCPCs to determine Vbus sourcing */
#define CONFIG_USB_PD_5V_EN_CUSTOM
#undef PD_POWER_SUPPLY_TURN_ON_DELAY
#undef PD_POWER_SUPPLY_TURN_OFF_DELAY
#undef CONFIG_USBC_VCONN_SWAP_DELAY_US
/* 20% margin added for these timings */
#define PD_POWER_SUPPLY_TURN_ON_DELAY 13080 /* us */
#define PD_POWER_SUPPLY_TURN_OFF_DELAY 16080 /* us */
#undef CONFIG_USBC_VCONN_SWAP_DELAY_US
#define CONFIG_USBC_VCONN_SWAP_DELAY_US 787 /* us */
/* I2C configuration */
#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0
#define I2C_PORT_BATTERY NPCX_I2C_PORT5_0
#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0
#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0
#define I2C_PORT_SUB_USB_C1 NPCX_I2C_PORT2_0
#define I2C_PORT_USB_MUX I2C_PORT_USB_C0
#define I2C_PORT_LCD NPCX_I2C_PORT3_0
/* TODO(b:147440290): Need to handle multiple charger ICs */
#define I2C_PORT_CHARGER I2C_PORT_USB_C0
#define I2C_PORT_ACCEL I2C_PORT_SENSOR
#define I2C_ADDR_EEPROM_FLAGS 0x50 /* 7b address */
#define I2C_ADDR_ISL98607_FLAGS 0x29
#define I2C_ADDR_MP3372_FLAGS 0x28
/* ISL98607 registers and value */
/* Enable VP / VN / VBST */
#define ISL98607_REG_ENABLE 0x05
#define ISL98607_VP_VN_VBST_EN 0x07
#define ISL97607_VP_VN_VBST_DIS 0x00
/* VBST Voltage Adjustment */
#define ISL98607_REG_VBST_OUT 0x06
#define ISL98607_VBST_OUT_5P65 0x0a
/* VN Voltage Adjustment */
#define ISL98607_REG_VN_OUT 0x08
#define ISL98607_VN_OUT_5P5 0x0a
/* VP Voltage Adjustment */
#define ISL98607_REG_VP_OUT 0x09
#define ISL98607_VP_OUT_5P5 0x0a
/* MP3372 registers and value */
/* ISET & CHEN */
#define MP3372_REG_ISET_CHEN 0x00
#define MP3372_ISET_21P8_CHEN_ALL 0x70ff
#define MP3372_ISET_19P4_CHEN_ALL 0x63ff
#define MP3372_ISET_18P0_CHEN_ALL 0x5cff
#define MP3372_ISET_15P8_CHEN_ALL 0x50ff
#define MP3372_ISET_15P3_CHEN_ALL 0x4eff
/*
* I2C pin names for baseboard
*
* Note: these lines will be set as i2c on start-up, but this should be
* okay since they're ODL.
*/
#define GPIO_EC_I2C_SUB_USB_C1_SCL GPIO_EC_I2C_SUB_C1_SCL_HDMI_EN_ODL
#define GPIO_EC_I2C_SUB_USB_C1_SDA GPIO_EC_I2C_SUB_C1_SDA_HDMI_HPD_ODL
/* Sensors */
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
#define CONFIG_ACCELGYRO_BMI160 /* Base accel */
/* Lid operates in forced mode, base in interrupt mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_ACCEL_FIFO
#define CONFIG_ACCEL_FIFO_SIZE 256 /* Must be a power of 2 */
#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3)
#define CONFIG_ACCELGYRO_BMI160_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */
#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_TABLET_MODE
#define CONFIG_TABLET_MODE_SWITCH
/* On-body detection */
#define CONFIG_BODY_DETECTION
#define CONFIG_BODY_DETECTION_SENSOR BASE_ACCEL
#define CONFIG_BODY_DETECTION_VAR_NOISE_FACTOR 150 /* % */
#define CONFIG_GESTURE_DETECTION
#define CONFIG_GESTURE_DETECTION_MASK BIT(CONFIG_BODY_DETECTION_SENSOR)
#define CONFIG_GESTURE_HOST_DETECTION
/* LIS2DS Lid accel */
#define CONFIG_ACCEL_LIS2DS
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum chg_id {
CHARGER_PRIMARY,
CHARGER_SECONDARY,
CHARGER_NUM,
};
enum temp_sensor_id {
TEMP_SENSOR_1,
TEMP_SENSOR_2,
TEMP_SENSOR_3,
TEMP_SENSOR_4,
TEMP_SENSOR_COUNT
};
enum adc_channel {
ADC_TEMP_SENSOR_1, /* ADC0 */
ADC_TEMP_SENSOR_2, /* ADC1 */
ADC_TEMP_SENSOR_3, /* ADC5 */
ADC_TEMP_SENSOR_4, /* ADC6 */
ADC_SUB_ANALOG, /* ADC2 */
ADC_VSNS_PP3300_A, /* ADC9 */
ADC_CH_COUNT
};
enum sensor_id { LID_ACCEL, BASE_ACCEL, BASE_GYRO, SENSOR_COUNT };
/* List of possible batteries */
enum battery_type {
BATTERY_SDI,
BATTERY_TYPE_COUNT,
};
void panel_power_change_interrupt(enum gpio_signal signal);
void lcd_reset_change_interrupt(enum gpio_signal signal);
void motion_interrupt(enum gpio_signal signal);
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
