summaryrefslogtreecommitdiff
path: root/board
Commit message (Expand)AuthorAgeFilesLines
* oak_pd: change oak_pd to be a sym link to glados_pdAlec Berg2015-11-0412-735/+16
* Dropping of DAP permission causes false alert when debugging.nagendra modadugu2015-11-041-1/+0
* Drop permissions to MEDIUM (APP level).nagendra modadugu2015-11-031-0/+35
* oak: using only one standby mode wakeup source.Ben Lok2015-11-031-1/+5
* cleanup: Standardize use of CONFIG_I2C and add MASTER/SLAVE CONFIGsShawn Nematbakhsh2015-11-0329-2/+40
* oak: handle the warm reset key from servo boardBen Lok2015-11-032-0/+3
* oak: Adding 2S and 3S battery supportBen Lok2015-11-031-6/+2
* it8380dev: fix irq, jtag and systemDino Li2015-11-011-0/+1
* glower: Remove boardShawn Nematbakhsh2015-10-307-318/+0
* glados: oak: chell: enable USB PD loggingAlec Berg2015-10-303-0/+6
* samus: increase POWERBTN task stack sizeAlec Berg2015-10-301-1/+1
* Jerry: enable virtual batteryMary Ruthven2015-10-291-0/+3
* Lars: enable USB-A port power controlRyan Zhang2015-10-282-4/+5
* Remove cyan ec configurationBernie Thompson2015-10-279-788/+0
* chell: Set SPI flash chip to W25X40Duncan Laurie2015-10-271-1/+1
* it8380dev: fix clock moduleDino Li2015-10-253-3/+13
* glados: oak: reboot EC if PD MCU crashesAlec Berg2015-10-235-21/+34
* ryu: fix lid close detectionVincent Palatin2015-10-231-1/+1
* ryu: do not pull EN_PP3300Vincent Palatin2015-10-231-1/+1
* common: lightbar: Add histeresis to prevent flickeringGwendal Grignou2015-10-231-4/+7
* board: ryu: Compass and Gyro stays up in S5Gwendal Grignou2015-10-231-2/+2
* mec1322: Remove CONFIG_PORT80_TASK_EN from boards.Aseda Aboagye2015-10-238-8/+0
* lars: remove port80 taskAlec Berg2015-10-231-2/+1
* glados: chell: add VCONN swap abilityAlec Berg2015-10-234-0/+20
* pd: change battery and variable sink cap for voltage inaccuracyAlec Berg2015-10-2310-20/+18
* oak: revise suspend gpio setting for rev4YH Huang2015-10-231-0/+4
* oak: stm32f0: implement i2c_set_timeoutRong Chang2015-10-231-7/+0
* Lars: Init boardRyan Zhang2015-10-2211-0/+1587
* Kunimitsu: Add support to enable L3GD20H gyrometerVijay Hiremath2015-10-212-0/+46
* kunimitsu: enable USB-A port power controlKevin K Wong2015-10-212-4/+5
* common: Add lightbar dimming based on outside light.Gwendal Grignou2015-10-202-0/+37
* oak_pd: reduce image size and build full RO and RWAlec Berg2015-10-202-8/+22
* Kunimitsu: Enable motion_sense_taskstabilize-smaug-7566.Bli feng2015-10-191-0/+1
* cr50: move tpm2 stubs.c file to this repositoryVadim Bendebury2015-10-192-1/+580
* mec1322: Change the Port 80 task to a timer IRQ.Aseda Aboagye2015-10-196-9/+4
* glados_pd: reduce image size and build full RO and RWAlec Berg2015-10-192-3/+24
* glados_pd: oak_pd: add and enable option for i2c slave onlyAlec Berg2015-10-192-0/+2
* stm32: add synchronous debug printfAlec Berg2015-10-196-57/+3
* Provide interface to random number generatorVadim Bendebury2015-10-173-8/+50
* Kunimitsu: PMIC: Keep the emergency reset time to defaultVijay Hiremath2015-10-171-11/+0
* nuc: Switch three GPIOs since lacking interrupt supportMulin Chao2015-10-161-21/+21
* common: motion: Fix forced mode computationGwendal Grignou2015-10-151-1/+1
* glados / kunimitsu / chell: Slow EC-->PD I2C bus to 500 KHzShawn Nematbakhsh2015-10-153-3/+3
* Skylake: Configure EC to use W25X40 flash instead of W25Q64Shamile Khan2015-10-152-2/+2
* GLaDOS: Kunimitsu: Chell: Reduce UART TX buffer to 512B.Aseda Aboagye2015-10-153-0/+9
* chell: Change image size to 100K.Aseda Aboagye2015-10-141-0/+3
* chell: remove pd_check_requested_voltage()Duncan Laurie2015-10-141-26/+0
* glados: kunimitsu: Change image size to 100K.stabilize-smaug-7547.BAseda Aboagye2015-10-132-0/+6
* Kunimitsu: implement x86 power cycle on EC resetVijay Hiremath2015-10-133-2/+40
* cleanup: pd: remove duplicate code for checking request msgAlec Berg2015-10-1316-343/+10
View Lorry Controller Status