summaryrefslogtreecommitdiff
path: root/board/cheza/gpio.inc
Commit message (Expand)AuthorAgeFilesLines
* cheza: Remove the internal PU for UART pinsWai-Hong Tam2018-10-311-1/+1
* cheza: Add internal PU for GPIO USB_C1_OC_ODLWai-Hong Tam2018-10-311-1/+1
* cheza: Configure GPIO RCAM_VSYNC to operate at 1.8VWai-Hong Tam2018-10-311-1/+1
* cheza: Remove the unnecessary GPIO_SEL_1P8V flagsWai-Hong Tam2018-10-311-5/+5
* cheza: Monitor the WARM_RESET_L signal to hold APWai-Hong Tam2018-10-301-4/+8
* cheza: Reenable EC hibernateWai-Hong Tam2018-10-041-3/+17
* cheza: Turn off 3.3V rail on S5Wai-Hong Tam2018-10-041-2/+1
* cheza: Change GPIO for the rev-3 boardWai-Hong Tam2018-10-031-13/+11
* cheza: Fix bmi160 interrupt pin settingPhilip Chen2018-10-031-1/+1
* cheza: Measure VBUS by ADCstabilize-atlas-11022.BPhilip Chen2018-08-311-1/+1
* cheza: Use POWER_GOOD signal instead of AP_RST_LWai-Hong Tam2018-08-311-2/+3
* Revert "cheza: Support confirmation of power lost"Wai-Hong Tam2018-08-311-1/+1
* cheza: Support base detectionWai-Hong Tam2018-08-291-1/+2
* cheza: Add more power signals for informative purposeWai-Hong Tam2018-08-291-5/+4
* cheza: Check switchcap GPIO0 which indicates outputting good voltageWai-Hong Tam2018-08-131-3/+7
* cheza: Enable display backlight controlWai-Hong Tam2018-08-061-1/+1
* cheza: Add 1.8V flags to the GPIOs talking to PMIC/AP or with 1.8V PUWai-Hong Tam2018-08-021-16/+18
* cheza: Correct I2C5 pin mask, change I2C7 to 1.8V, and remove PUWai-Hong Tam2018-08-021-11/+14
* cheza: Enable PWM for display backlightWai-Hong Tam2018-07-261-0/+1
* cheza: Enable ADC channelsWai-Hong Tam2018-07-261-0/+1
* cheza: Change GPIO for the rev-1 boardWai-Hong Tam2018-07-261-12/+17
* cheza: Support accel/gyroPhilip Chen2018-06-151-1/+1
* cheza: Switch USB port-0 HS to the hubWai-Hong Tam2018-06-011-2/+2
* Cheza: Support host command over SPIWai-Hong Tam2018-05-261-1/+2
* cheza: Check power enough and enable PP5000 when power-on APWai-Hong Tam2018-05-221-7/+1
* cheza: Support PD and chargingTom Wai-Hong Tam2018-05-091-10/+11
* cheza: Change ACOK_OD pin to EC inputTom Wai-Hong Tam2018-05-081-5/+5
* cheza: Remove internal pull-up for the BATT_PRES_ODL pinTom Wai-Hong Tam2018-05-081-1/+1
* cheza: Support confirmation of power lostTom Wai-Hong Tam2018-05-081-1/+1
* cheza: Enable AP_RST_REQ as a request from AP to reset itselfWai-Hong Tam2018-05-081-1/+1
* cheza: Add SDM845 power sequence for rev-0 boardWai-Hong Tam2018-05-041-2/+3
* cheza: Add initial support for ChezaWai-Hong Tam2018-04-171-0/+142
View Lorry Controller Status