summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
...
* Common: move for loop initial declarationDiana Z2019-04-181-2/+6
* USB PD: Suspend ports when resetting TCPCs during cold rebootDiana Z2019-04-161-1/+9
* TCPC: Set charger vbus during initDiana Z2019-04-161-0/+7
* octopus: correct GPIO - KB_BL_PWR_EN to UNIMPLEMENTEDMarco Chen2019-04-164-8/+8
* casta:Turn on green led when charge state is idleYongBeum Ha2019-04-111-1/+1
* anx7447.c: change VBUS present detection interfaceXin Ji2019-03-291-6/+5
* bloog: add batteries configurationDevin Lu2019-03-262-2/+240
* bloog: Remove support for board version 0Devin Lu2019-03-201-15/+0
* Phaser: Remove support for early board versionsDiana Z2019-03-201-15/+0
* Fleex: Remove support for board version 0Diana Z2019-03-202-35/+1
* Meep: Remove support for board version 0Diana Z2019-03-201-15/+0
* bloog: add flash_ec supportDevin Lu2019-03-191-0/+4
* casta : Turn on blue led when system is onYongBeum Ha2019-03-181-1/+5
* bloog: initial EC imageDevin Lu2019-03-147-0/+825
* PD: Set Rp consistently on initial connection, increasing laterDiana Z2019-03-112-19/+13
* USB-PD: Disable Vconn on SRC_DISCONNECTDaisuke Nojiri2019-03-111-1/+4
* common/usb_pd_protocol: Set port in LPM at the start of initKarthikeyan Ramasubramanian2019-03-021-0/+8
* Fleex: Implement new polymer battery parametermatt_wang2019-03-012-0/+177
* Ampton: Correct HPD GPIOsDiana Z2019-03-011-2/+2
* Ampton: tune the gyro axis and directionJames_Chao2019-02-271-1/+7
* Battery: add support battery-cutoff SMBus block write functionmatt_wang2019-02-274-11/+94
* temp_sensor: Guard thermistor readings by their power rail enable gpioScott Collyer2019-02-261-6/+33
* Ampton: correct thermistor reading functionDiana Z2019-02-142-8/+2
* Casta: Tune USB mux registersDiana Z2019-02-141-0/+10
* driver/lsm6dsm: Fix issue while setting Magnetometer ODRKarthikeyan Ramasubramanian2019-02-131-11/+4
* Meep: remove magnetometerDiana Z2019-02-132-31/+0
* driver: bmi160: for reference, add for lis2mdl supportGwendal Grignou2019-02-111-0/+5
* driver: lsm6dsm: Integrate LIS2MDL behind LSM6DSMGwendal Grignou2019-02-1113-255/+375
* driver: lsm6dsm: Clean register definitionGwendal Grignou2019-02-111-53/+83
* board: indent sensor_motion arraysGwendal Grignou2019-02-114-264/+264
* common: sensor: Honor roundup flag for rangeGwendal Grignou2019-02-112-1/+3
* ec_commands: Add missing definition for LIS2MDLGwendal Grignou2019-02-112-0/+4
* config: Add magnetometer definitionsGwendal Grignou2019-02-117-15/+69
* ps8xxx: put the PS8751's power role to sink stateJames_Chao2019-02-011-1/+17
* casta : charger overrideYongBeum Ha2019-01-281-0/+1
* Fleex: Add new LED state for fully charged in S5Diana Z2019-01-283-3/+25
* casta:enable pull-up of usb mux0 interruptYongBeum Ha2019-01-281-0/+11
* driver: lsm6dsm: add reboot at init timeDevin Lu2019-01-252-0/+51
* Ampton: Set the PS8751 to source mode before enter low power modeJames_Chao2019-01-246-4/+21
* casta : implement ledYongBeum Ha2019-01-244-4/+132
* casta : Add battery informationYongBeum Ha2019-01-243-3/+167
* octopus/ampton: disable espi pad when system goes into G3Dino Li2019-01-231-0/+20
* Revert "casta : add battery information"Karthikeyan Ramasubramanian2019-01-233-168/+3
* it83xx: add enable/disable espi pad functionDino Li2019-01-233-4/+18
* charge_ramp: Allow USB-C power to be ramped by hardwareDaisuke Nojiri2019-01-221-7/+22
* tcpm/it83xx.c: don't reload cc parameter settings for DxRuibin Chang2019-01-222-0/+4
* driver/ppc/nx20p348.c: Handle overcurrent eventKarthikeyan Ramasubramanian2019-01-221-5/+2
* board/octopus: Notify SoC about USB overcurrentKarthikeyan Ramasubramanian2019-01-226-0/+59
* USB PD: PPC: Add overcurrent handling.Aseda Aboagye2019-01-2214-38/+307
* cheza: Add the interrupt of port-1 overcurrentWai-Hong Tam2019-01-222-4/+20
View Lorry Controller Status