1 files changed, 113 insertions, 0 deletions
diff --git a/board/herobrine/board.h b/board/herobrine/board.h
new file mode 100644
index 0000000000..790d753bbc
--- /dev/null
+++ b/board/herobrine/board.h
@@ -0,0 +1,113 @@
+/* Copyright 2021 The Chromium OS Authors. All rights reserved.
+ * Use of this source code is governed by a BSD-style license that can be
+ * found in the LICENSE file.
+ */
+
+/* Herobrine board configuration */
+
+#ifndef __CROS_EC_BOARD_H
+#define __CROS_EC_BOARD_H
+
+#include "baseboard.h"
+
+/* TODO(waihong): Remove the following bringup features */
+#define CONFIG_BRINGUP
+#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands. */
+#define CONFIG_USB_PD_DEBUG_LEVEL 3
+#define CONFIG_CMD_GPIO_EXTENDED
+#define CONFIG_CMD_POWERINDEBUG
+#define CONFIG_I2C_DEBUG
+
+/* Keyboard */
+#define CONFIG_KEYBOARD_PROTOCOL_MKBP
+#define CONFIG_KEYBOARD_REFRESH_ROW3
+
+#define CONFIG_PWM_KBLIGHT
+
+/* Battery */
+#define CONFIG_BATTERY_DEVICE_CHEMISTRY  "LION"
+#define CONFIG_BATTERY_REVIVE_DISCONNECT
+#define CONFIG_BATTERY_FUEL_GAUGE
+
+/* BC 1.2 Charger */
+#define CONFIG_BC12_DETECT_PI3USB9201
+
+/* USB */
+#define CONFIG_USB_PD_TCPM_PS8805
+#define CONFIG_USBC_PPC_SN5S330
+#define CONFIG_USB_PD_PORT_MAX_COUNT 2
+
+/* USB-A */
+#define USB_PORT_COUNT 1
+#define CONFIG_USB_PORT_POWER_DUMB
+
+/* Sensors */
+/* BMI260 Base accel/gyro */
+#define CONFIG_ACCELGYRO_BMI260
+#define CONFIG_ACCEL_INTERRUPTS
+#define CONFIG_ACCELGYRO_BMI260_INT_EVENT \
+	TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
+#define OPT3001_I2C_ADDR_FLAGS OPT3001_I2C_ADDR1_FLAGS
+
+/* BMA253 lid accel */
+#define CONFIG_ACCEL_BMA255
+#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
+
+#define CONFIG_LID_ANGLE
+#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
+#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
+#define CONFIG_LID_ANGLE_UPDATE
+
+#define CONFIG_TABLET_MODE
+#define CONFIG_TABLET_MODE_SWITCH
+#define CONFIG_GMR_TABLET_MODE
+
+/* GPIO alias */
+#define GPIO_AC_PRESENT		GPIO_ACOK_OD
+#define GPIO_WP_L		GPIO_EC_WP_ODL
+#define GPIO_SWITCHCAP_PG	GPIO_SRC_VPH_PWR_PG
+#define GPIO_ACOK_OD		GPIO_CHG_ACOK_OD
+#define GPIO_EN_PP5000		GPIO_EN_PP5000_S5
+#define GPIO_POWER_GOOD		GPIO_MB_POWER_GOOD
+#define GPIO_EC_INT_L		GPIO_AP_EC_INT_L
+#define GPIO_DP_HOT_PLUG_DET	GPIO_DP_HOT_PLUG_DET_R
+
+#ifndef __ASSEMBLER__
+
+#include "gpio_signal.h"
+#include "registers.h"
+
+enum adc_channel {
+	ADC_VBUS,
+	ADC_AMON_BMON,
+	ADC_PSYS,
+	ADC_CH_COUNT
+};
+
+/* Motion sensors */
+enum sensor_id {
+	LID_ACCEL = 0,
+	BASE_ACCEL,
+	BASE_GYRO,
+	SENSOR_COUNT,
+};
+
+enum pwm_channel {
+	PWM_CH_KBLIGHT = 0,
+	PWM_CH_DISPLIGHT,
+	PWM_CH_COUNT
+};
+
+/* List of possible batteries */
+enum battery_type {
+	BATTERY_AP16L5J,
+	BATTERY_TYPE_COUNT,
+};
+
+/* Reset all TCPCs. */
+void board_reset_pd_mcu(void);
+void board_set_tcpc_power_mode(int port, int mode);
+
+#endif /* !defined(__ASSEMBLER__) */
+
+#endif /* __CROS_EC_BOARD_H */