diff options
Diffstat (limited to 'board/drobit/gpio.inc')
| -rw-r--r-- | board/drobit/gpio.inc | 16 |
1 files changed, 8 insertions, 8 deletions
diff --git a/board/drobit/gpio.inc b/board/drobit/gpio.inc index 7699dddf85..1e7ff5120f 100644 --- a/board/drobit/gpio.inc +++ b/board/drobit/gpio.inc @@ -25,13 +25,11 @@ GPIO_INT(PG_EC_DSW_PWROK, PIN(C, 7), GPIO_INT_BOTH, power_signal_interrupt) GPIO_INT(PG_EC_ALL_SYS_PWRGD, PIN(F, 4), GPIO_INT_BOTH, power_signal_interrupt) /* Sensor Interrupts */ -GPIO_INT(EC_IMU_INT_L, PIN(5, 6), GPIO_INT_FALLING | GPIO_SEL_1P8V, bmi260_interrupt) -GPIO_INT(TABLET_MODE_L, PIN(9, 5), GPIO_INT_BOTH, gmr_tablet_switch_isr) + /* * Lid g-sensor interrupt unused on Volteer, configure as regular input for * power saving. */ -GPIO(EC_ACCEL_INT, PIN(8, 1), GPIO_INPUT | GPIO_PULL_UP) /* USB-C interrupts */ GPIO_INT(USB_C0_TCPC_INT_ODL, PIN(E, 0), GPIO_INT_BOTH, tcpc_alert_event) @@ -46,8 +44,6 @@ GPIO_INT(USB_C1_MIX_INT_ODL, PIN(0, 3), GPIO_INT_BOTH, bc12_interrupt) /* HDMI interrupts */ /* Volume button interrupts */ -GPIO_INT(EC_VOLDN_BTN_ODL, PIN(9, 3), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) -GPIO_INT(EC_VOLUP_BTN_ODL, PIN(9, 7), GPIO_INT_BOTH | GPIO_PULL_UP, button_interrupt) /* Power Sequencing Signals */ GPIO(EN_PP3300_A, PIN(A, 3), GPIO_OUT_LOW) @@ -110,6 +106,10 @@ GPIO(UNUSED_GPIOF2, PIN(F, 2), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIO96, PIN(9, 6), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIO34, PIN(3, 4), GPIO_INPUT | GPIO_PULL_UP) GPIO(UNUSED_GPIOD4, PIN(D, 4), GPIO_INPUT | GPIO_PULL_UP) +GPIO(UNUSED_GPIO56, PIN(5, 6), GPIO_INPUT | GPIO_PULL_UP) +GPIO(UNUSED_GPIO81, PIN(8, 1), GPIO_INPUT | GPIO_PULL_UP) +GPIO(UNUSED_GPIO95, PIN(9, 5), GPIO_INPUT | GPIO_PULL_UP) + /* Only connected to test points */ GPIO(EC_KB_BL_EN, PIN(8, 6), GPIO_INPUT | GPIO_PULL_UP) GPIO(EC_ESPI_ALERT_L, PIN(5, 7), GPIO_INPUT | GPIO_PULL_UP) @@ -122,8 +122,8 @@ GPIO(EC_ESPI_ALERT_L, PIN(5, 7), GPIO_INPUT | GPIO_PULL_UP) GPIO(EC_EDP_BL_EN, PIN(D, 3), GPIO_OUT_HIGH) /* I2C pins - Alternate function below configures I2C module on these pins */ -GPIO(EC_I2C0_SENSOR_SCL, PIN(B, 5), GPIO_INPUT | GPIO_SEL_1P8V) -GPIO(EC_I2C0_SENSOR_SDA, PIN(B, 4), GPIO_INPUT | GPIO_SEL_1P8V) +GPIO(EC_I2C0_USB_C1_MIX_SCL, PIN(B, 5), GPIO_INPUT) /* Reserved for USB4 retimer port 1 */ +GPIO(EC_I2C0_USB_C1_MIX_SDA, PIN(B, 4), GPIO_INPUT) /* Reserved for USB4 retimer port 1 */ GPIO(EC_I2C1_USB_C0_SCL, PIN(9, 0), GPIO_INPUT) GPIO(EC_I2C1_USB_C0_SDA, PIN(8, 7), GPIO_INPUT) GPIO(EC_I2C2_USB_C1_SCL, PIN(9, 2), GPIO_INPUT) @@ -139,7 +139,7 @@ GPIO(EC_I2C7_EEPROM_PWR_SDA_R, PIN(B, 2), GPIO_INPUT) GPIO(EC_BATT_PRES_ODL, PIN(E, 1), GPIO_INPUT) /* Alternate functions GPIO definitions */ -ALTERNATE(PIN_MASK(B, BIT(5) | BIT(4)), 0, MODULE_I2C, (GPIO_INPUT | GPIO_SEL_1P8V)) /* I2C0 */ +ALTERNATE(PIN_MASK(B, BIT(5) | BIT(4)), 0, MODULE_I2C, 0) /* I2C0 */ ALTERNATE(PIN_MASK(9, BIT(0) | BIT(2) | BIT(1)), 0, MODULE_I2C, 0) /* I2C1 SCL / I2C2 */ ALTERNATE(PIN_MASK(8, BIT(7)), 0, MODULE_I2C, 0) /* I2C1 SDA */ ALTERNATE(PIN_MASK(D, BIT(1) | BIT(0)), 0, MODULE_I2C, 0) /* I2C3 */ |