diff options
Diffstat (limited to 'baseboard/asurada/baseboard.h')
| -rw-r--r-- | baseboard/asurada/baseboard.h | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/baseboard/asurada/baseboard.h b/baseboard/asurada/baseboard.h new file mode 100644 index 0000000000..97576a32ef --- /dev/null +++ b/baseboard/asurada/baseboard.h @@ -0,0 +1,196 @@ +/* Copyright 2021 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + */ + +/* Asurada board configuration */ + +#ifndef __CROS_EC_BASEBOARD_H +#define __CROS_EC_BASEBOARD_H + +/* IT81202-bx config */ +/* + * NOTE: we need to make correct VCC voltage selection here if EC's VCC isn't + * connect to 1.8v on other versions. + */ +#define CONFIG_IT83XX_VCC_1P8V + +/* + * On power-on, H1 releases the EC from reset but then quickly asserts and + * releases the reset a second time. This means the EC sees 2 resets: + * (1) power-on reset, (2) reset-pin reset. This config will + * allow the second reset to be treated as a power-on. + */ +#define CONFIG_BOARD_RESET_AFTER_POWER_ON +#define CONFIG_BOARD_VERSION_CUSTOM +#define CONFIG_CHIPSET_MT8192 +#define CONFIG_EXTPOWER_GPIO +#define CONFIG_HIBERNATE_WAKE_PINS_DYNAMIC +#define CONFIG_POWER_SLEEP_FAILURE_DETECTION +#define CONFIG_POWER_TRACK_HOST_SLEEP_STATE + +/* Chipset */ +#define CONFIG_CMD_AP_RESET_LOG +#define CONFIG_CMD_POWERINDEBUG +#define CONFIG_HOST_COMMAND_STATUS +#define CONFIG_LOW_POWER_IDLE +#define CONFIG_LOW_POWER_S0 +#define CONFIG_POWER_BUTTON +#define CONFIG_POWER_COMMON +#define CONFIG_PWM +#define CONFIG_VBOOT_HASH +#define CONFIG_VOLUME_BUTTONS +#define CONFIG_WP_ACTIVE_HIGH + +/* Battery */ +#define CONFIG_BATTERY_CUT_OFF +#define CONFIG_BATTERY_FUEL_GAUGE +#define CONFIG_BATTERY_PRESENT_GPIO GPIO_EC_BATT_PRES_ODL +#define CONFIG_BATTERY_SMART + +/* BC12 */ +#define CONFIG_BC12_DETECT_MT6360 +#define CONFIG_BC12_DETECT_PI3USB9201 +#undef CONFIG_BC12_SINGLE_DRIVER +#define CONFIG_USB_CHARGER + +/* Charger */ +#define ADC_AMON_BMON ADC_CHARGER_AMON_R /* ADC name remap */ +#define ADC_PSYS ADC_CHARGER_PMON /* ADC name remap */ +#define CONFIG_CHARGE_MANAGER +#define CONFIG_CHARGER +#define CONFIG_CHARGE_RAMP_HW +#define CONFIG_CHARGER_DISCHARGE_ON_AC +#define CONFIG_CHARGER_INPUT_CURRENT 512 +#define CONFIG_CHARGER_ISL9238C +#define CONFIG_CHARGER_MAINTAIN_VBAT +#define CONFIG_CHARGER_OTG +#define CONFIG_CHARGER_PSYS +#define CONFIG_CHARGER_PSYS_READ +#define CONFIG_CHARGER_SENSE_RESISTOR 10 /* BOARD_RS2 */ +#define CONFIG_CHARGER_SENSE_RESISTOR_AC 20 /* BOARD_RS1 */ +#define CONFIG_CMD_CHARGER_ADC_AMON_BMON + +/* Keyboard */ +#define CONFIG_CMD_KEYBOARD +#define CONFIG_KEYBOARD_COL2_INVERTED +#define CONFIG_KEYBOARD_PROTOCOL_MKBP +#define CONFIG_MKBP_USE_GPIO + +/* I2C */ +#define CONFIG_I2C +#define CONFIG_I2C_CONTROLLER +#define CONFIG_I2C_PASSTHRU_RESTRICTED +#define CONFIG_I2C_VIRTUAL_BATTERY +#define I2C_PORT_CHARGER IT83XX_I2C_CH_A +#define I2C_PORT_BATTERY IT83XX_I2C_CH_A +#define I2C_PORT_ACCEL IT83XX_I2C_CH_B +#define I2C_PORT_PPC0 IT83XX_I2C_CH_C +#define I2C_PORT_PPC1 IT83XX_I2C_CH_E +#define I2C_PORT_USB_MUX0 IT83XX_I2C_CH_C +#define I2C_PORT_USB_MUX1 IT83XX_I2C_CH_E +#define I2C_PORT_VIRTUAL_BATTERY I2C_PORT_BATTERY +#define CONFIG_SMBUS_PEC + +/* LED */ +#define CONFIG_LED_COMMON + +/* PD / USB-C / PPC */ +#define CONFIG_CMD_PPC_DUMP +#define CONFIG_HOSTCMD_PD_CONTROL +#define CONFIG_IT83XX_TUNE_CC_PHY +#define CONFIG_USB_MUX_VIRTUAL +#define CONFIG_USBC_PPC +#define CONFIG_USBC_PPC_DEDICATED_INT +#define CONFIG_USBC_PPC_POLARITY +#define CONFIG_USBC_PPC_SYV682C +#define CONFIG_USBC_PPC_VCONN +#define CONFIG_USBC_SS_MUX +#define CONFIG_USBC_VCONN +#define CONFIG_USBC_VCONN_SWAP +#define CONFIG_USB_DRP_ACC_TRYSRC +#define CONFIG_USB_MUX_IT5205 /* C0 */ +#define CONFIG_USB_MUX_PS8743 /* C1 */ +#define CONFIG_USB_PD_ALT_MODE +#define CONFIG_USB_PD_ALT_MODE_DFP +#define CONFIG_USB_PD_DECODE_SOP +#define CONFIG_USB_PD_DISCHARGE +#define CONFIG_USB_PD_DISCHARGE_PPC +#define CONFIG_USB_PD_DP_HPD_GPIO +#define CONFIG_USB_PD_DP_HPD_GPIO_CUSTOM +#define CONFIG_USB_PD_DUAL_ROLE +#define CONFIG_USB_PD_FRS_PPC +#define CONFIG_USB_PD_ITE_ACTIVE_PORT_COUNT 2 +#define CONFIG_USB_PD_LOGGING +#define CONFIG_USB_PD_PORT_MAX_COUNT 2 +#define CONFIG_USB_PD_REV30 +#define CONFIG_USB_PD_TCPC_LOW_POWER +#define CONFIG_USB_PD_TCPM_ITE_ON_CHIP +#define CONFIG_USB_PD_TCPM_TCPCI +#define CONFIG_USB_PD_TCPMV2 +#define CONFIG_USB_PD_TRY_SRC +#define CONFIG_USB_PD_VBUS_DETECT_PPC +#define CONFIG_USB_PD_VBUS_MEASURE_ADC_EACH_PORT +#define CONFIG_USB_PID 0x5053 +#define CONFIG_USB_POWER_DELIVERY + +/* USB-A */ +#define CONFIG_USB_PORT_POWER_DUMB +#define CONFIG_USB_PORT_POWER_DUMB_CUSTOM_HOOK +#define USB_PORT_COUNT USBA_PORT_COUNT + +/* UART */ +#undef CONFIG_UART_TX_BUF_SIZE +#define CONFIG_UART_TX_BUF_SIZE 4096 + +/* Sensor */ +#ifdef HAS_TASK_MOTIONSENSE +#define CONFIG_CMD_ACCEL_INFO +#define CONFIG_CMD_ACCELS + +#define CONFIG_ACCEL_FIFO +#define CONFIG_ACCEL_FIFO_SIZE 256 +#define CONFIG_ACCEL_FIFO_THRES (CONFIG_ACCEL_FIFO_SIZE / 3) +#define CONFIG_ACCEL_INTERRUPTS +#endif + +/* SPI / Host Command */ +#define CONFIG_SPI + +/* MKBP */ +#define CONFIG_MKBP_EVENT + +#define CONFIG_KEYBOARD_PROTOCOL_MKBP +#define CONFIG_MKBP_USE_GPIO + +/* Voltage regulator control */ +#define CONFIG_HOSTCMD_REGULATOR + +/* Define the host events which are allowed to wakeup AP in S3. */ +#define CONFIG_MKBP_HOST_EVENT_WAKEUP_MASK \ + (EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_CONNECTED) | \ + EC_HOST_EVENT_MASK(EC_HOST_EVENT_AC_DISCONNECTED) | \ + EC_HOST_EVENT_MASK(EC_HOST_EVENT_LID_OPEN) | \ + EC_HOST_EVENT_MASK(EC_HOST_EVENT_HANG_DETECT) | \ + EC_HOST_EVENT_MASK(EC_HOST_EVENT_MODE_CHANGE) | \ + EC_HOST_EVENT_MASK(EC_HOST_EVENT_POWER_BUTTON)) + +/* And the MKBP events */ +#define CONFIG_MKBP_EVENT_WAKEUP_MASK \ + (BIT(EC_MKBP_EVENT_KEY_MATRIX) | \ + BIT(EC_MKBP_EVENT_HOST_EVENT)) + +#include "baseboard_common.h" + +#ifndef __ASSEMBLER__ + +#include "gpio_signal.h" +#include "registers.h" +#include "power/mt8192.h" + +void board_reset_pd_mcu(void); +enum board_sub_board board_get_sub_board(void); +void usb_a0_interrupt(enum gpio_signal signal); + +#endif /* !__ASSEMBLER__ */ +#endif /* __CROS_EC_BASEBOARD_H */ |