Wizpig: update gpio table

Update gpio table to meet wizpig's schematic design.

BUG=None
BRANCH=firmware-strago-7287.B
TEST=make buildall -j
Signed-off-by: Chris Wang <chriswang@ami.com.tw>

Change-Id: Ia13340f44ff074430109c723288006ee59cd8b51
Reviewed-on: https://chromium-review.googlesource.com/317141
Reviewed-by: Ted Kuo <tedkuo@ami.com.tw>
Reviewed-by: Shawn N <shawnn@chromium.org>
Commit-Queue: Chris Wang <chriswang@ami.com.tw>
Tested-by: Chris Wang <chriswang@ami.com.tw>

1 files changed, 12 insertions, 11 deletions

diff --git a/board/wizpig/gpio.inc b/board/wizpig/gpio.inc
index 32a55cb67a..960c598454 100644
--- a/board/wizpig/gpio.inc
+++ b/board/wizpig/gpio.inc
@@ -51,11 +51,12 @@ GPIO(USB2_ENABLE,       PIN(36), GPIO_OUT_LOW)                  /* Enable power
 GPIO(ENTERING_RW,       PIN(41), GPIO_OUT_LOW)                  /* Indicate when EC is entering RW code */
 GPIO(PCH_SMI_L,         PIN(44), GPIO_ODR_HIGH)                 /* SMI output */
 GPIO(USB_OC1_L,         PIN(45), GPIO_INT_FALLING)              /* DB2 BC1.2 over current signal to EC */
-GPIO(DP_USB_C_HPD_Q,    PIN(46), GPIO_OUT_HIGH)                 /* DP hot plug detect from EC to SOC */
+GPIO(EMR_FWE1,          PIN(46), GPIO_OUT_HIGH)                 /* Flash Mode Compulsory Rewrite */
+GPIO(NC_GPIO47,         PIN(47), GPIO_INPUT | GPIO_PULL_UP)     /* NC */
 
-GPIO(OTG_SW_EN,         PIN(50), GPIO_OUT_LOW)                  /* */
+GPIO(NC_GPIO50,         PIN(50), GPIO_INPUT | GPIO_PULL_UP)     /* NC */
 GPIO(PCH_SUS_STAT_L,    PIN(51), GPIO_INT_FALLING)              /* Signal to inform EC that SOC is entering low power state */
-GPIO(EC_ACDET_CTRL,     PIN(52), GPIO_INPUT | GPIO_PULL_UP)
+GPIO(NC_GPIO52,         PIN(52), GPIO_INPUT | GPIO_PULL_UP)
 GPIO(TRACKPAD_PWREN,    PIN(53), GPIO_OUT_HIGH)                 /* Enable power for Track Pad */
 GPIO(USB_OC0_L,         PIN(55), GPIO_INT_FALLING)              /* Over current signal of the BC1.2 charger to EC */
 GPIO(EC_ADC1,           PIN(57), GPIO_INPUT)                    /* EC_ADC1, TEMP_SENSOR_2 no_stuff */
@@ -72,37 +73,37 @@ GPIO(BOARD_VERSION3,    PIN(102), GPIO_INPUT)                   /* BOARD_ID2 */
 GPIO(USB_CTL1,          PIN(105), GPIO_OUT_HIGH)                /* USB charging mode control */
 
 GPIO(PCH_RCIN_L,        PIN(110), GPIO_ODR_HIGH)                /* Reset line to PCH (for 8042 emulation) */
-GPIO(NC_115,            PIN(115), GPIO_INPUT | GPIO_PULL_UP)    /* NC */
+GPIO(NC_GPIO115,        PIN(115), GPIO_INPUT | GPIO_PULL_UP)    /* NC */
 GPIO(EC_VNN_VCLK,       PIN(122), GPIO_INPUT | GPIO_PULL_UP)    /* Interrupt from USB PD Controller to EC */
 GPIO(STRAP_L,           PIN(123), GPIO_OUT_LOW)
 GPIO(EC_VNN_ALERT_L,    PIN(124), GPIO_INPUT | GPIO_PULL_UP)
-GPIO(GYRO_INT2,         PIN(127), GPIO_INPUT | GPIO_PULL_DOWN)   /* Gyro sensor interrupt 2 to EC */
+GPIO(AB_SENSOR_INT,     PIN(127), GPIO_INPUT | GPIO_PULL_DOWN)   /* Gyro sensor interrupt 2 to EC */
 
 GPIO(EC_PLUG_DETECT,    PIN(132), GPIO_INT_BOTH | GPIO_PULL_UP | GPIO_PULL_DOWN)
 GPIO(PD_RST_L,          PIN(135), GPIO_ODR_HIGH)                 /* USB PD MCU reset */
 
-GPIO(THERMAL_PROBE_EN_L,PIN(140), GPIO_OUT_HIGH)
+GPIO(NC_GPIO140,        PIN(140), GPIO_INPUT | GPIO_PULL_UP)     /* NC */
 GPIO(PCH_RSMRST_L,      PIN(143), GPIO_OUT_LOW)                  /* RSMRST_N to PCH */
 GPIO(EC_KBD_ALERT,      PIN(145), GPIO_OUT_LOW)                   /* EC_KBD_ALERT */
 GPIO(PVT_CS0,           PIN(146), GPIO_ODR_HIGH)                 /* SPI PVT Chip select */
-GPIO(ALS_INT,           PIN(147), GPIO_INPUT | GPIO_PULL_UP)     /* ALS sensor interrupt to EC */
+GPIO(ES_RESET,          PIN(147), GPIO_ODR_HIGH)                 /* EMR reset */
 
 GPIO(WLAN_OFF_L,        PIN(150), GPIO_ODR_HIGH)                 /* Wireless LAN */
 GPIO(CPU_PROCHOT,       PIN(151), GPIO_OUT_LOW)
 GPIO(KBD_IRQ_L,         PIN(152), GPIO_ODR_HIGH)                 /* Negative edge triggered irq. */
 GPIO(BOARD_VERSION1,    PIN(154), GPIO_INPUT)                    /* BOARD_ID0 */
-GPIO(EC_PERICOM_INT,    PIN(155), GPIO_INT_BOTH)                 /* Pericom USB device interrupt */
+GPIO(NC_GPIO155,        PIN(155), GPIO_INPUT | GPIO_PULL_UP)     /* NC */
 GPIO(PWR_BTN_SELECT,    PIN(156), GPIO_ODR_HIGH)                 /* HIGH in clamshell mode and LOW in tablet mode */
 GPIO(PCH_SUSPWRDNACK,   PIN(157), GPIO_INT_FALLING)              /* PMC SUSPWRDNACK signal from SOC to EC */
 
 GPIO(PCH_PWRBTN_L,      PIN(160), GPIO_OUT_HIGH)                 /* Power button output to PCH */
-GPIO(GYRO_INT1,         PIN(161), GPIO_INPUT | GPIO_PULL_DOWN)   /* Gyro sensor interrupt 1 to EC */
-GPIO(VP9_CODEC_RESET_L, PIN(163), GPIO_OUT_LOW)                  /* VP9_CODEC_RESET_L, OUTPUT, ACTIVE LOW */
+GPIO(CD_SENSOR_INIT,    PIN(161), GPIO_INPUT | GPIO_PULL_DOWN)   /* Gyro sensor interrupt 1 to EC */
+GPIO(NC_GPIO163,        PIN(163), GPIO_INPUT | GPIO_PULL_UP)     /* NC */
 
 GPIO(STARTUP_LATCH_SET, PIN(201), GPIO_INPUT)			/* Not used in BCRD2. Programmed as Input to fix EC power leakage in S3*/
 GPIO(EC_BL_DISABLE_L,   PIN(202), GPIO_OUT_HIGH)                 /* EDP backligh disable signal from EC */
 GPIO(SMC_SHUTDOWN,      PIN(203), GPIO_OUT_LOW)                  /* Shutdown signal from EC to power sequencing PLD */
-GPIO(USBPD_BST_OFF,     PIN(204), GPIO_OUT_LOW)
+GPIO(NC_GPIO204,        PIN(204), GPIO_INPUT | GPIO_PULL_UP)     /* NC */
 
 GPIO(SUSPWRDNACK_SOC_EC,PIN(210), GPIO_OUT_LOW)                  /* SUSPWRDNACK signal from MOIC device to EC */
 GPIO(GPIO_3_EC,         PIN(211), GPIO_OUT_LOW)                  /* Sleep SOIX signal from SOC to EC */