blob: 945cbd4ee7b1c2353046fb0befce3f2764232a35 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
/*
* (C) Copyright 2005, Psyent Corporation <www.psyent.com>
* Scott McNutt <smcnutt@psyent.com>
* (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* BOARD/CPU
*/
#include "../board/altera/nios2-generic/custom_fpga.h" /* fpga parameters */
#define CONFIG_BOARD_NAME "nios2-generic" /* custom board name */
#define CONFIG_BOARD_EARLY_INIT_F /* enable early board-spec. init */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_NIOS_SYSID_BASE CONFIG_SYS_SYSID_BASE
/*
* SERIAL
*/
#define CONFIG_ALTERA_JTAG_UART
#if defined(CONFIG_ALTERA_JTAG_UART)
# define CONFIG_SYS_NIOS_CONSOLE CONFIG_SYS_JTAG_UART_BASE
#else
# define CONFIG_SYS_NIOS_CONSOLE CONFIG_SYS_UART_BASE
#endif
#define CONFIG_ALTERA_JTAG_UART_BYPASS
#define CONFIG_SYS_NIOS_FIXEDBAUD
#define CONFIG_BAUDRATE CONFIG_SYS_UART_BAUD
#define CONFIG_SYS_BAUDRATE_TABLE {CONFIG_BAUDRATE}
#define CONFIG_SYS_CONSOLE_INFO_QUIET /* Suppress console info */
/*
* TIMER
*/
#define CONFIG_SYS_LOW_RES_TIMER
#define CONFIG_SYS_NIOS_TMRBASE CONFIG_SYS_TIMER_BASE
#define CONFIG_SYS_NIOS_TMRIRQ CONFIG_SYS_TIMER_IRQ
#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/
#define CONFIG_SYS_NIOS_TMRCNT \
(CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_TIMER_FREQ / 1000) - 1)
/*
* STATUS LED
*/
#define CONFIG_ALTERA_PIO
#define CONFIG_SYS_ALTERA_PIO_NUM 1
#define CONFIG_SYS_ALTERA_PIO_GPIO_NUM LED_PIO_WIDTH
#define CONFIG_STATUS_LED /* Enable status driver */
#define CONFIG_BOARD_SPECIFIC_LED
#define CONFIG_GPIO_LED /* Enable GPIO LED driver */
#define CONFIG_GPIO /* Enable GPIO driver */
#define LED_PIO_BASE USER_LED_PIO_8OUT_BASE
#define LED_PIO_WIDTH 8
#define LED_PIO_RSTVAL 0xff
#define STATUS_LED_BIT 0 /* Bit-0 on GPIO */
#define STATUS_LED_STATE 1 /* Blinking */
#define STATUS_LED_PERIOD (500 / CONFIG_SYS_NIOS_TMRMS) /* 500 msec */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#ifdef CONFIG_CMD_NET
# define CONFIG_CMD_DHCP
# define CONFIG_CMD_PING
#endif
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_LMB
/*
* ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
* CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
* reset address, no? This will keep the environment in user region
* of flash. NOTE: the monitor length must be multiple of sector size
* (which is common practice).
*/
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SIZE 0x20000 /* 128k, 1 sector */
#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
#define CONFIG_ENV_ADDR ((CONFIG_SYS_RESET_ADDR + \
CONFIG_SYS_MONITOR_LEN) | \
CONFIG_SYS_FLASH_BASE)
/*
* MEMORY ORGANIZATION
* -Monitor at top of sdram.
* -The heap is placed below the monitor
* -The stack is placed below the heap (&grows down).
*/
#define CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256k */
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_SDRAM_BASE + \
CONFIG_SYS_SDRAM_SIZE - \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x20000)
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_INIT_SP CONFIG_SYS_MALLOC_BASE
/*
* MISC
*/
#define CONFIG_SYS_LONGHELP /* Provide extended help */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
#define CONFIG_SYS_MAXARGS 16 /* Max command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Bootarg buf size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + \
16) /* Print buf size */
#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_INIT_SP - 0x20000)
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_HUSH_PARSER
#endif /* __CONFIG_H */
|
