1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
|
/*
* Copyright (C) 2015 Timesys Corporation
* Copyright (C) 2015 General Electric Company
* Copyright (C) 2014 Advantech
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Configuration settings for the GE MX6Q Bx50v3 boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __GE_BX50V3_CONFIG_H
#define __GE_BX50V3_CONFIG_H
#include <asm/arch/imx-regs.h>
#include <asm/mach-imx/gpio.h>
#define BX50V3_BOOTARGS_EXTRA
#if defined(CONFIG_TARGET_GE_B450V3)
#define CONFIG_BOARD_NAME "General Electric B450v3"
#elif defined(CONFIG_TARGET_GE_B650V3)
#define CONFIG_BOARD_NAME "General Electric B650v3"
#elif defined(CONFIG_TARGET_GE_B850V3)
#define CONFIG_BOARD_NAME "General Electric B850v3"
#undef BX50V3_BOOTARGS_EXTRA
#define BX50V3_BOOTARGS_EXTRA "video=DP-1:1024x768@60 " \
"video=HDMI-A-1:1024x768@60 "
#else
#define CONFIG_BOARD_NAME "General Electric BA16 Generic"
#endif
#define CONFIG_MXC_UART_BASE UART3_BASE
#define CONSOLE_DEV "ttymxc2"
#define CONFIG_SUPPORT_EMMC_BOOT
#include "mx6_common.h"
#include <linux/sizes.h>
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
#define CONFIG_HW_WATCHDOG
#define CONFIG_IMX_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT_MSECS 6000
#define CONFIG_LAST_STAGE_INIT
#define CONFIG_MXC_UART
#define CONFIG_MXC_OCOTP
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#endif
/* MMC Configs */
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_BOUNCE_BUFFER
/* USB Configs */
#ifdef CONFIG_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_MASS_STORAGE
#endif
/* Networking Configs */
#ifdef CONFIG_NET
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 4
#define CONFIG_PHY_ATHEROS
#endif
/* Serial Flash */
#ifdef CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_LOADADDR 0x12000000
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcause=POR\0" \
"bootlimit=10\0" \
"image=/boot/fitImage\0" \
"fdt_high=0xffffffff\0" \
"dev=mmc\0" \
"devnum=1\0" \
"rootdev=mmcblk0p\0" \
"quiet=quiet loglevel=0\0" \
"console=" CONSOLE_DEV "\0" \
"setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
"ro rootwait cma=128M " \
"bootcause=${bootcause} " \
"${quiet} console=${console} ${rtc_status} " \
BX50V3_BOOTARGS_EXTRA "\0" \
"doquiet=" \
"if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
"then setenv quiet; fi\0" \
"hasfirstboot=" \
"ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
"/boot/bootcause/firstboot\0" \
"swappartitions=" \
"setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
"msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
"echo $msg; " \
"setenv stdout vga; " \
"echo \"\n\n\n\n \" $msg; " \
"setenv stdout serial; " \
"mw.b 0x7000A000 0xbc; " \
"mw.b 0x7000A001 0x00; " \
"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
"altbootcmd=" \
"run doquiet; " \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run hasfirstboot || setenv partnum 0; " \
"if test ${partnum} != 0; then " \
"setenv bootcause REVERT; " \
"run swappartitions loadimage doboot; " \
"fi; " \
"run failbootcmd\0" \
"loadimage=" \
"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
"doboot=" \
"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
"run setargs; " \
"bootm ${loadaddr}#conf@${confidx}\0" \
"tryboot=" \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run loadimage || run swappartitions && run loadimage || " \
"setenv partnum 0 && echo MISSING IMAGE;" \
"run doboot; " \
"run failbootcmd\0" \
#define CONFIG_MMCBOOTCOMMAND \
"if mmc dev ${devnum}; then " \
"run doquiet; " \
"run tryboot; " \
"fi; " \
#define CONFIG_USBBOOTCOMMAND \
"echo Unsupported; " \
#ifdef CONFIG_CMD_USB
#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND
#else
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
#endif
#define CONFIG_ARP_TIMEOUT 200UL
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* environment organization */
#define CONFIG_ENV_SIZE (8 * 1024)
#define CONFIG_ENV_OFFSET (768 * 1024)
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#ifndef CONFIG_SYS_DCACHE_OFF
#endif
#define CONFIG_SYS_FSL_USDHC_NUM 3
/* Framebuffer */
#define CONFIG_VIDEO
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_FG_COL 0xFF
#define CONFIG_SYS_CONSOLE_BG_COL 0x00
#define CONFIG_HIDE_LOGO_VERSION
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
#define CONFIG_CMD_BMP
#endif
#define CONFIG_PWM_IMX
#define CONFIG_IMX6_PWM_PER_CLK 66000000
#define CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
#define CONFIG_RTC_RX8010SJ
#define CONFIG_SYS_RTC_BUS_NUM 2
#define CONFIG_SYS_I2C_RTC_ADDR 0x32
/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_MXC_I2C1
#define CONFIG_SYS_I2C_MXC_I2C2
#define CONFIG_SYS_I2C_MXC_I2C3
#define CONFIG_SYS_NUM_I2C_BUSES 11
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
{1, {I2C_NULL_HOP} }, \
{2, {I2C_NULL_HOP} }, \
{0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
}
#define CONFIG_BCH
#define CONFIG_BOOTCOUNT_EXT
#define CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE "mmc"
#define CONFIG_SYS_BOOTCOUNT_EXT_DEVPART "1:5"
#define CONFIG_SYS_BOOTCOUNT_EXT_NAME "/boot/failures"
#define CONFIG_SYS_BOOTCOUNT_ADDR 0x7000A000
#endif /* __GE_BX50V3_CONFIG_H */
|
