summaryrefslogtreecommitdiff
path: root/doc/board/emulation/qemu-arm.rst
blob: 8d7fda10f15e9120ba253d959c34712e8273a3c5 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
.. SPDX-License-Identifier: GPL-2.0+
.. Copyright (C) 2017, Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

QEMU ARM
========

QEMU for ARM supports a special 'virt' machine designed for emulation and
virtualization purposes. This document describes how to run U-Boot under it.
Both 32-bit ARM and AArch64 are supported.

The 'virt' platform provides the following as the basic functionality:

    - A freely configurable amount of CPU cores
    - U-Boot loaded and executing in the emulated flash at address 0x0
    - A generated device tree blob placed at the start of RAM
    - A freely configurable amount of RAM, described by the DTB
    - A PL011 serial port, discoverable via the DTB
    - An ARMv7/ARMv8 architected timer
    - PSCI for rebooting the system
    - A generic ECAM-based PCI host controller, discoverable via the DTB

Additionally, a number of optional peripherals can be added to the PCI bus.

Building U-Boot
---------------
Set the CROSS_COMPILE environment variable as usual, and run:

- For ARM::

    make qemu_arm_defconfig
    make

- For AArch64::

    make qemu_arm64_defconfig
    make

Running U-Boot
--------------
The minimal QEMU command line to get U-Boot up and running is:

- For ARM::

    qemu-system-arm -machine virt -bios u-boot.bin

- For AArch64::

    qemu-system-aarch64 -machine virt -cpu cortex-a57 -bios u-boot.bin

Note that for some odd reason qemu-system-aarch64 needs to be explicitly
told to use a 64-bit CPU or it will boot in 32-bit mode.

Additional persistent U-boot environment support can be added as follows:

- Create envstore.img using qemu-img::

    qemu-img create -f raw envstore.img 64M

- Add a pflash drive parameter to the command line::

    -drive if=pflash,format=raw,index=1,file=envstore.img

Additional peripherals that have been tested to work in both U-Boot and Linux
can be enabled with the following command line parameters:

- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.::

    -drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0

- To add an Intel E1000 network adapter, pass e.g.::

    -netdev user,id=net0 -device e1000,netdev=net0

- To add an EHCI-compliant USB host controller, pass e.g.::

    -device usb-ehci,id=ehci

- To add a NVMe disk, pass e.g.::

    -drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo

These have been tested in QEMU 2.9.0 but should work in at least 2.5.0 as well.

Debug UART
----------

The debug UART on the ARM virt board uses these settings::

    CONFIG_DEBUG_UART=y
    CONFIG_DEBUG_UART_PL010=y
    CONFIG_DEBUG_UART_BASE=0x9000000
    CONFIG_DEBUG_UART_CLOCK=0