summaryrefslogtreecommitdiff
path: root/configs/kmcoge5ne_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* mpc83xx: Don't allow W and G bits in IBATsChristophe Leroy2023-05-011-3/+0
| | | | | | | | | | | | | | | | | The "Programming Environments Manual for 32-Bit Implementations of the PowerPC™ Architecture" says "W and G bits are not defined for IBAT registers. Attempting to write to these bits causes boundedly-undefined results" The "e300 Power Architecture™ Core Family Reference Manual" says the same: "Neither the W or G bits of the IBAT registers should be set. Attempting to write to these bits causes boundedly-undefined results." Remove the possibility to set those bytes. Fixes: 30915ab95d9 ("mpc83xx: Migrate BATS config to Kconfig") Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Mario Six <mario.six@gdsys.cc>
* configs: Resync with savedefconfigTom Rini2023-05-011-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* powerpc, mpc83xx: Remove CONFIG_ELBC_BRx_ORxChristophe Leroy2023-03-061-37/+0
| | | | | | | | | | | | | | | | Commit fe7d654d04 ("mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to Kconfig") converted CONFIG_SYS_{BRx/ORx}_PRELIM to Kconfig by implementing a fine-grained selection of every bit in Kconfig. But commit c7fad78ec0 ("Convert CONFIG_SYS_BR0_PRELIM et al to Kconfig") reworked it so that you now just have to provide the raw value of each register in Kconfig. However, all fine-grained Kconfig items remained allthough they are not used anymore. Remove them all. Fixes: c7fad78ec0 ("Convert CONFIG_SYS_BR0_PRELIM et al to Kconfig") Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
* Convert CONFIG_FLASH_SHOW_PROGRESS to KconfigTom Rini2022-12-221-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_FLASH_SHOW_PROGRESS Signed-off-by: Tom Rini <trini@konsulko.com>
* km/ppc: migrate all mpc83xx to DM_I2CHolger Brunck2022-12-121-6/+3
| | | | | | | Enable DM_I2C and I2C mux to get rid of the usage of the legacy i2c driver. Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
* km/powerpc: migrate to env.txt fileHolger Brunck2022-12-121-1/+1
| | | | | | | Use already present common.env file and add a powerpc specific env so that we can move all the environment defines to text files. Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
* post: Migrate to KconfigTom Rini2022-12-051-0/+1
| | | | | | | | We move the existing CONFIG_POST_* functionality over to CFG_POST and then introduce CONFIG_POST to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_NAND_KMETER1 et al to KconfigTom Rini2022-12-051-0/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_NAND_ECC_BCH CONFIG_NAND_KIRKWOOD CONFIG_NAND_KMETER1 Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_HWCONFIG to KconfigTom Rini2022-12-051-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_HWCONFIG Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_MONITOR_LEN to KconfigTom Rini2022-11-101-0/+1
| | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SYS_LOADS_BAUD_CHANGE et al to KconfigTom Rini2022-11-101-0/+2
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_LOADS_BAUD_CHANGE CONFIG_LOADS_ECHO As part of this, we move CMD_SAVES to be after CMD_LOADS as they are logically related (load or save an s-record format file) and this makes grouping of CONFIG_SYS_LOADS_BAUD_CHANGE easier. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SYS_INIT_RAM_LOCK to KconfigTom Rini2022-11-101-0/+1
| | | | | | | | This converts the following to Kconfig: CONFIG_SYS_INIT_RAM_LOCK Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASESimon Glass2022-10-311-1/+1
| | | | | | | | | The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <sjg@chromium.org>
* Convert CONFIG_SYS_BOOTM_LEN to KconfigTom Rini2022-07-071-0/+1
| | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_BOOTM_LEN As part of this, rework error handling in boot/bootm.c so that we pass the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not be available to host tools but we do know the size that we passed to malloc(). Cc: Soeren Moch <smoch@web.de> Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_BOOTCOUNT_LE et al to KconfigTom Rini2022-07-071-0/+1
| | | | | | | | This converts the following to Kconfig: CONFIG_SYS_BOOTCOUNT_LE CONFIG_SYS_BOOTCOUNT_BE Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_CBSIZE to KconfigTom Rini2022-06-061-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_CBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_PBSIZE to KconfigTom Rini2022-06-061-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_MAXARGS to KconfigTom Rini2022-06-061-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2022-04-081-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2022-04-011-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ETHPRIME to KconfigTom Rini2022-03-181-0/+2
| | | | | | | | | | | This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_BOOTP_MAY_FAIL et al to KconfigTom Rini2022-03-031-0/+1
| | | | | | | | | | | | This converts the following to Kconfig: CONFIG_BOOTP_MAY_FAIL CONFIG_BOOTP_VENDOREX CONFIG_BOOTP_BOOTFILESIZE CONFIG_BOOTP_NISDOMAIN CONFIG_BOOTP_TIMEOFFSET Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_83XX_PCICLK to KconfigTom Rini2021-12-271-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_83XX_PCICLK Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_BR0_PRELIM et al to KconfigTom Rini2021-12-011-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_BR0_PRELIM CONFIG_SYS_OR1_PRELIM CONFIG_SYS_BR1_PRELIM CONFIG_SYS_OR2_PRELIM CONFIG_SYS_BR2_PRELIM CONFIG_SYS_OR2_PRELIM CONFIG_SYS_BR3_PRELIM CONFIG_SYS_OR3_PRELIM CONFIG_SYS_BR4_PRELIM CONFIG_SYS_OR4_PRELIM CONFIG_SYS_BR5_PRELIM CONFIG_SYS_OR5_PRELIM CONFIG_SYS_BR6_PRELIM CONFIG_SYS_OR6_PRELIM CONFIG_SYS_BR7_PRELIM CONFIG_SYS_OR7_PRELIM This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL to platforms that had not been previously migrated. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini2021-08-311-0/+1
| | | | | | | Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
* i2c: fsl_i2c: Migrate to KconfigTom Rini2021-08-301-0/+6
| | | | | | | | | | | - As there are no boards that use different values for speed / slave on different buses, use a single option. - Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options. - Introduce _HAS_ options for additional buses as only the first one is common to all users. - Convert all remaining symbols to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini2021-08-301-0/+1
| | | | | | | | | | | First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to KconfigTom Rini2021-08-301-0/+3
| | | | | | | | | | | | | - Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2021-06-281-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigWIP/2020-10-09-kconfig-reorgTom Rini2020-10-091-5/+5
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mpc83xx, keymile boards: enable DM_ETH and add DTSHeiko Schocher2020-09-171-4/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enable DTS support for keymile mpc83xx based boards. get rid of compile warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Therefore done: - add DTS for all mpc83xx based boards from keymile mainly they are not mainlined to linux. - add u-boot specific dtsi - add stdout-path - add missing ucc4 par_io definitions, which were in board code, but not in linux DTS - remove not used ethernet nodes Signed-off-by: Heiko Schocher <hs@denx.de> Patch-cc: Mario Six <mario.six@gdsys.cc> Patch-cc: Qiang Zhao <qiang.zhao@nxp.com> Series-to: u-boot Series-version: 3 Series-changes: 3 - rebase patchset to current mainline commit c0192950df - update defconfig files Series-changes: 2 - add patch which fixes Codingstyle errors in drivers/qe - add patch which converts the mpc83xx based boards from keymile to DM_ETH Cover-letter: powerpc, mpc83xx: add DM_ETH support This patch series adds DM ethernet support for mpc83xx based keymile boards. Travis build: END
* Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford2020-07-281-0/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-02-061-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-01-221-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* ppc/km: enable DM driver support in all defconfigsHolger Brunck2019-12-231-0/+2
| | | | | | | | | | | This is the first step to use DM support for the KM powerpc boards. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> CC: Mario Six <mario.six@gdsys.cc> CC: Wolfgang Denk <wd@denx.de> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com> CC: Priyanka Jain <priyanka.jain@nxp.com>
* ppc/km: convert KM_DEF_NETDEV to KconfigHolger Brunck2019-12-231-0/+1
| | | | | | | | | | Remove this from the board header files and move it to Kconfig. Also use the correct default address for kmtegr1. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> CC: Priyanka Jain <priyanka.jain@nxp.com> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
* configs: Resync with savedefconfigWIP/04Dec2019Tom Rini2019-12-041-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flashMiquel Raynal2019-12-041-0/+2
| | | | | | | | | | | | Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini <trini@konsulko.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENTTom Rini2019-11-121-0/+1
| | | | | | | | Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-05-261-46/+41
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_FMAN_ENET and some related options to KconfigTom Rini2019-05-261-0/+1
| | | | | | | | | Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini <trini@konsulko.com>
* mpc83xx: Migrate CONFIG_LCRR_* to KconfigMario Six2019-05-211-0/+3
| | | | | | Migrate the CONFIG_LCRR_* settings to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate arbiter config to KconfigMario Six2019-05-211-0/+4
| | | | | | Migrate the arbiter configuration to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate HID config to KconfigMario Six2019-05-211-0/+3
| | | | | | Mirate the HID configuration settings to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to KconfigMario Six2019-05-211-0/+42
| | | | | | | | | | | Migrate the BR/OR settings to Kconfig. These must be known at compile time, so cannot be configured via DT. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate LBLAW_* to KconfigMario Six2019-05-211-0/+12
| | | | | | | | | | | | The LBLAW_* values determine the window configuration of the memory controller. Hence, they must be known at compile time, and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Migrate BATS config to KconfigMario Six2019-05-211-0/+79
| | | | | | | | | | | | The BATs (block address translation registers) determine the initial memory window mappings. Hence, they must be known at compile time and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* powerpc: Migrate HIGH_BATS to KconfigMario Six2019-05-211-0/+1
| | | | | | Migrate the CONFIG_HIGH_BATS variable to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
* mpc83xx: Kconfig: Migrate HRCW to KconfigMario Six2019-05-211-0/+9
| | | | | | | | | | | | | The HRCW (hardware reset configuration word) is a constant that must be hard-coded into the boot loader image. So, it must be available at compile time, and cannot be migrated to the DT mechanism, but has to be kept in Kconfig. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
View Lorry Controller Status