summaryrefslogtreecommitdiff
path: root/configs/inet_q972_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt2019-04-291-0/+1
| | | | | | | | | Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-04-291-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-02-071-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: usb: Switch to Generic host controllersJagan Teki2019-01-181-0/+1
| | | | | | | | | | | | | | Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
* configs: Resync with savedefconfigTom Rini2018-09-031-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini2018-08-161-0/+1
| | | | | | | | | | | We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
* part: Disable CONFIG_SPL_ISO_PARTITION by defaultAlexander Graf2018-04-161-1/+0
| | | | | | | | | | | | | | | | We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf <agraf@suse.de>
* configs: Resync with savedefconfigTom Rini2018-04-071-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigsAndre Przywara2018-03-141-1/+0
| | | | | | | | | | | | | | | | | Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence of moving the common definition shared by almost every sunxi board into 123 individual defconfig files. But the U-Boot start address for Allwinner boards is a platform decision which has been around for ages, so defining it in each *board* config file seems a bit over the top. Define the standard values (160MB into DRAM for most SoCs, with two SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from the individual defconfigs. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
* configs: Migrate CONFIG_SYS_TEXT_BASETom Rini2018-02-111-0/+1
| | | | | | | | | | | On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
* cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen2018-02-051-1/+0
| | | | | | | | | | | | | | | | | | cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
* cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen2017-10-101-1/+0
| | | | | | | | | | | | | | Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* configs: Migrate all of the existing USB symbols, except fastbootTom Rini2017-09-011-0/+1
| | | | | | | | | | | | This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: Tom Rini <trini@konsulko.com>
* disk: convert CONFIG_EFI_PARTITION to KconfigPatrick Delaunay2017-01-281-0/+1
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* disk: convert CONFIG_ISO_PARTITION to KconfigPatrick Delaunay2017-01-281-0/+1
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* disk: convert CONFIG_DOS_PARTITION to KconfigPatrick Delaunay2017-01-281-0/+1
| | | | | Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
* configs: Resync with savedefconfigTom Rini2016-09-091-1/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* sun6i: Add defconfig and dts file for tablets using the inet-q972 PCBHans de Goede2016-08-261-0/+23
Add a defconfig and dts file for tablets using the generic inet-q972 PCB. Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host, micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot, (mini) power-barrel and an usb wifi module. This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet. The dts files are identical to the ones submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
View Lorry Controller Status