summaryrefslogtreecommitdiff
path: root/configs/imx6q_logic_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* i2c: Rename SPL/TPL_I2C_SUPPORT to I2CSimon Glass2021-07-281-1/+1
| | | | | | | Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
* Rename GPIO_SUPPORT to GPIOSimon Glass2021-07-281-1/+1
| | | | | | Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
* Rename SPL_USB_HOST_SUPPORT to SPL_USB_HOSTSimon Glass2021-07-281-1/+1
| | | | | | Rename this option so that CONFIG_IS_ENABLED can be used with it. Signed-off-by: Simon Glass <sjg@chromium.org>
* Rename SPL_WATCHDOG_SUPPORT to SPL_WATCHDOGSimon Glass2021-07-281-1/+1
| | | | | | Rename this option so that CONFIG_IS_ENABLED can be used with it. Signed-off-by: Simon Glass <sjg@chromium.org>
* configs: Resync with savedefconfigTom Rini2021-07-261-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2021-06-281-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2021-05-251-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: enable LTO for some boardsMarek Behún2021-05-241-0/+1
| | | | | | | | | | Enable LTO for some boards that were tested by people on U-Boot Mailing List. Signed-off-by: Marek Behún <marek.behun@nic.cz> Tested-by: Adam Ford <aford173@gmail.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tim Harvey <tharvey@gateworks.com>
* configs: Resync with savedefconfigTom Rini2020-11-301-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigWIP/2020-10-09-kconfig-reorgTom Rini2020-10-091-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* arm: mx6: Make all i.MX6 SoCs user-selectableTom Rini2020-08-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have a number of platforms that are a combination of a carrier board and System-on-Module (SoM) that in turn allows for the board to have different SoCs on it. In some cases, this is handled via board-specific Kconfig options. In other cases we make use of CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid configurations as we will not in turn get options that in Kconfig are selected by or depend on that setting. To resolve this, make the SoC option a choice in Kconfig and make boards depend on what they can support. This change opens us up for further clean-ups in the cases where a single CONFIG_TARGET_xxx can support different SoCs and today they do not, or do not cleanly do so. Reported-by: Matt Porter <mporter@konsulko.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Soeren Moch <smoch@web.de> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Heiko Schocher <hs@denx.de> Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de> Cc: Ludwig Zenz <lzenz@dh-electronics.de> Cc: Lukasz Majewski <lukma@denx.de> Cc: Akshay Bhat <akshaybhat@timesys.com> Cc: Ken Lin <Ken.Lin@advantech.com.tw> Cc: Ian Ray <ian.ray@ge.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it> Cc: Simone CIANNI <simone.cianni@bticino.it> Cc: Adam Ford <aford173@gmail.com> Cc: Marcin Niestroj <m.niestroj@grinn-global.com> Cc: "Eric Bénard" <eric@eukrea.com> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Jason Liu <jason.hui.liu@nxp.com> Cc: Ye Li <ye.li@nxp.com> Cc: Eric Nelson <eric@nelint.com> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Parthiban Nallathambi <parthiban@linumiz.com> Cc: Marek Vasut <marex@denx.de> Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Niel Fourie <lusus@denx.de> Cc: Martyn Welch <martyn.welch@collabora.com> Cc: Richard Hu <richard.hu@technexion.com> Cc: Stefan Roese <sr@denx.de> Cc: Boris Brezillon <bbrezillon@kernel.org> Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com> Cc: Breno Lima <breno.lima@nxp.com> Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org> Cc: Silvio Fricke <open-source@softing.de> Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
* configs: Resync with savedefconfigv2020.10-rc2Tom Rini2020-08-101-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford2020-07-281-0/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-07-281-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-07-061-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* treewide: mem: Move mtest related defines to KconfigWIP/2020-05-07-more-kconfig-migrationsAshok Reddy Soma2020-05-081-0/+2
| | | | | | | | | | | Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-04-281-4/+3
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-01-221-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Kconfig: Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMAVignesh Raghavendra2020-01-151-1/+1
| | | | | | | | | Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use macros such as CONFIG_IS_ENABLED() that allow conditional compilation of code for SPL and U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* configs: Resync with savedefconfigWIP/04Dec2019Tom Rini2019-12-041-2/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mtd: ensure CMD_NAND is compiled when its options are selectedMiquel Raynal2019-12-041-0/+1
| | | | | | | | In some files, options of CMD_NAND are selected but not the command itself. Fix this inconsistency. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
* mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flashMiquel Raynal2019-12-041-0/+1
| | | | | | | | | | | | Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini <trini@konsulko.com>
* mtd: rename CONFIG_MTD -> CONFIG_DM_MTDMiquel Raynal2019-12-031-1/+1
| | | | | | | | | | CONFIG_MTD must be reserved for the MTD core. Like any other subsystem, prefix the symbol by DM when it comes to DM support. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Add Kconfig files] Signed-off-by: Tom Rini <trini@konsulko.com>
* mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NANDMiquel Raynal2019-12-031-1/+1
| | | | | | | | | Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
* env: Finish migration of common ENV optionsTom Rini2019-11-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
* env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini2019-11-201-0/+1
| | | | | | | | | | | Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: imx6q_logic: Enable Pin muxing in SPLAdam Ford2019-10-131-0/+1
| | | | | | | | | | | | | With the 256KB of OCRAM available to SPL now, there should be enough room to enable the pinmuxing in SPL from the device tree. This patch enables SPL_PINCTRL et al and adds the serial and usdhc pin mux references to the -u-boot.dtsi file so the pins can be configured from the device tree. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
* ARM: imx6q_logic: Enable 256KB OCRAMAdam Ford2019-10-131-0/+1
| | | | | | | | | | | | Since this board config only supports, the i.MX6D/i.MX6Q configurations, 256K of on-chip RAM is available which increases the space available to SPL to help further reduce board code and further enable device tree functions. This patch enables 256K of RAM. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
* ARM: imx6q_logic: Enable DM_SERIALAdam Ford2019-10-081-0/+1
| | | | | | | | | | | | In order to call preloader_console_init from board_init_f when DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access to DM and device tree. This patch calls spl_early_init just before preloader_console_init() and enables DM_SERIAL and SPL_DM_SERIAL. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
* configs: Resync with savedefconfigTom Rini2019-09-231-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* mtd: nand: raw: Move CONFIG_SYS_NAND_USE_FLASH_BBT to KconfigStefan Roese2019-08-251-0/+1
| | | | | | | | | | | | | | | | | | Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs, headers and whitelist. Please note that this symbol already was used in Kconfig (imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was not available in Kconfig. This changes now with this patch and all boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what I also need on my GARDENA AT91SAM based board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> [trini: Rework such that the configs are unchanged to start with] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-08-251-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_FSL_USDHC to KconfigAdam Ford2019-08-231-1/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2019-08-141-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: imx6q_logic: Enable SPL_DM with SPL_OF_CONTROLAdam Ford2019-07-191-0/+6
| | | | | | | | With the spl code correctly returning either MMC1 or MMC2, this board can not boot either from internal eMMC (MMC1) or the uSD card on the baseboard (MMC2) using the device tree. Signed-off-by: Adam Ford <aford173@gmail.com>
* Convert to use fsl_esdhc_imx for i.MX platformsYangbo Lu2019-06-231-1/+1
| | | | | | | | | | | Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
* Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imxTom Rini2019-05-011-1/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | Porting to DM and i.MX8 ------------------------ - warp7 to DM - kp_imx53 to DM - Warnings in DT - MX8QM support - colibri-imx6ull to DM - imx7d-pico to DM - ocotp for MX8
| * ARM: imx6q_logic: Allow storing environment in FAT on eMMCAdam Ford2019-04-251-1/+3
| | | | | | | | | | | | | | | | | | Some variations of the imx6q_logic board have eMMC instead of NAND. Rather than creating a separate defconfig, this patch adds the ability to read/write to eMMC (mmc 0:1) when NAND doesn't exist. Signed-off-by: Adam Ford <aford173@gmail.com>
* | configs: move CONFIG_SPL_TEXT_BASE to KconfigSimon Goldschmidt2019-04-291-0/+1
| | | | | | | | | | | | | | | | | | Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com>
* | configs: Resync with savedefconfigTom Rini2019-04-291-1/+1
|/ | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: imx6q_logic: Enable UUID supportAdam Ford2019-03-311-0/+1
| | | | | | | | With UUID support, the root can now point to UUID. This makes swiching between mmc 0 and mmc 1 easier by simplying changing mmcdev between 0 and 1. From there, the scripts handle the rest. Signed-off-by: Adam Ford <aford173@gmail.com>
* ARM: imx6q_logic: Enable MTD and NAND_MXS_DTAdam Ford2019-03-131-0/+3
| | | | | | | | This patch supports enabling MTD, and the corresponding CMD_MTD along with enabling the MXS NAND Controller with device tree support. Signed-off-by: Adam Ford <aford173@gmail.com>
* ARM: imx6q_logic: Enable SPL Booting from NANDAdam Ford2019-02-151-1/+3
| | | | | | | This patch fixes a few values that were incorrect, and this now lets SPL boot from NAND. Signed-off-by: Adam Ford <aford173@gmail.com>
* configs: Resync with savedefconfigTom Rini2019-02-071-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FATTien Fong Chee2019-02-011-1/+1
| | | | | | | | | | Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: imx6q_logic: Enable Falcon Mode and fatwriteAdam Ford2019-01-281-0/+2
| | | | | | | | | This patch enables Falcon Mode by default and updates the README file to show instructions on how to run from the micro SD card or eMMC. This patch also enables fatwrite to help assist with writing the 'args' to the microSD card. Signed-off-by: Adam Ford <aford173@gmail.com>
* ARM: imx6q_logic: Enable DM_USB and dependent regulatorsAdam Ford2019-01-281-0/+5
| | | | | | | With the updated device trees in place, this patch enables DM_USB which uses several regulators also enabled with this patch. Signed-off-by: Adam Ford <aford173@gmail.com>
* imx6q_logic: Enable MMC booting from SPLAdam Ford2019-01-281-9/+6
| | | | | | | | The MMC booting wasn't previously fitting into the codespace. This patch enables MMC booting from the baseboard by reducing some DM overhead during SPL. Signed-off-by: Adam Ford <aford173@gmail.com>
* Kconfig: Migrate BOUNCE_BUFFERPhilipp Tomsich2019-01-191-0/+1
| | | | | | | | | | | | | | | | | | | | | | The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
* Kconfig: rename CONFIG_SPL_USB_GADGET_SUPPORT as CONFIG_SPL_USB_GADGETJean-Jacques Hiblot2019-01-101-1/+1
| | | | | | | The SPL option for USB gadget should be named after the option for u-boot (CONFIG_USB_GADGET) Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
View Lorry Controller Status