| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
| |
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
corruption
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This reverts commit 232ed3ca534708527a9515c7c41bc3542949525c.
In exynos boards, ${console} is used to set bootargs but it sets
without "console=", so CONFIG_DEFAULT_CONSOLE for these boards is
designated with "console=" but it is removed. So revert the commit.
References for using ${console} in
board/samsung/common/bootscripts/autoboot.cmd
board/samsung/common/bootscripts/bootzimg.cmd
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
updated READM.odroid for supported Odroid HC1 development board.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Add missing exynos5422-odroidhc1.dtb needed to set for dfu env.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
| |\ \
| | |
| | |
| | |
| | | |
Fixes:
- rockchip: rk3399: fix missing braces in full pinctrl
|
| |/ /
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Braces around the error-case for rk3399_pinctrl_set_pin_pupd lead to
an unconditional (and unintended) return from the function without it
ever setting pin-configurations.
Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
| |\ \
| | |
| | |
| | | |
TrueType fixes and documentation
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With enabled default Nimbus font dm_test_video_truetype* tests fail.
Update expected expressions to fix them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
As an example of how to enable TrueType fonts, move chromebook_jerry over
to use these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
At present it is possible to enable TrueType support but not include any
fonts. This results in a blank display. Select Nimbus as the default font
to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
U-Boot supports using TrueType fonts on the console, which is useful for
presenting a nice UI to users, e.g. for system recovery.
Add information about how to compile this on ARM platforms, since this is
not obvious.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Last-minute fixes for 2019.1:
- clamp DRAM size to below 32bit for 32bit targets to support 4GB
- fix copyright notice on some Rockchip-contributed files
- adjust vdd_log for the RK3399-Q7 to improve stability in some workloads
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch enables the full pinctrl driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds a Kconfig option to enable the full pinctrl driver
for the RK3399. This flag needs to be enabed in order to get the
features of the full pinctrl driver compiled in (i.e. a .set_state()
callback).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The current pinctrl driver for the RK3399 has a range of qulity issues.
E.g. it only implements the .set_state_simple() callback, it
does not parse the available pinctrl information from the DTS
(instead uses hardcoded values), is not flexible enough to cover
devices without 'interrupt' field in the DTS (e.g. PWM),
is not written generic enough to make code reusable among other
rockchip SoCs...
This patch addresses these issues by reimplementing the whole driver
from scratch using the .set_state() callback.
The new implementation covers all featurese of the old code
(i.e. it supports pinmuxing and pullup/pulldown configuration).
This patch has been tested on a RK3399-Q7 SoM (Puma).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
pinctrl_decode_pin_config_dm() is basically a feature-equivalent
implementation of pinctrl_decode_pin_config(), which operates
on struct udevice devices and uses the dev_read_*() API.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch enables the PWM regulator driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch allows to enable the PWM regulator driver
independent for U-Boot and SPL.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Rockchip may use this sdram copy of source code for both open source
and internal project, update the license to use both GPL2.0+ and
BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
All the source code of sdram_rk3036.c are from Rockchip, update the
copyright to owned by Rockchip.
Because rockchip may use this copy of code both for open source
project and internal project, update the license to use both
GPL2.0+ and BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
| |\ \ \ \
| |/ / /
|/| | | |
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Migration plan for DM_SPI_FLASH is v2019.07 since it
depends on DM_SPI migration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.
Note: there were many updates on this deadline, so better
not update this again.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch adds Hynix H27UBG8T2BTR id table as part of raw nand,
these chips were available in some A20-olinuxino-micro boards.
Signed-off-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
[jagan: add proper commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Current driver doesn't check if the destination pointer is NULL.
This cause the data from the FIFO to be stored inside the internal
SDRAM ( address 0 ).
The patch add simple check if the destination pointer is NULL.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: fix commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
| |\ \ \ \ |
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Commit a8011eb84dfa("sunxi: board: Print error after power initialization
fails") moved the DRAM init after the increase of the CPU clock
frequency. This lead to various DRAM initialisation failures on some
boards (hangs or wrong size reported, on a NanoPi Duo2 and OrangePi
Zero, for instance). Lowering the CPU frequency significantly (for instance
to 408 MHz) seems to work around the problem, so this points to some timing
issues in the DRAM code.
Debugging this sounds like a larger job, so let's just revert this patch
to bring back those boards.
Beside this probably unintended change the patch just moved the error
message around, so reverting this is not a real loss.
This reverts commit a8011eb84dfac5187cebf00ed8bc981bdb5c1fa1.
Tested-By: Priit Laes <plaes@plaes.org>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
| |\ \ \ \
| |_|/ /
|/| | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
imx for 2019.01
- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" causes U-Boot to hang because of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This commit adds support for device tree and enumeration via device model
for the Vybrid's NFC NAND driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This commit provides code to add proper entry to Kconfig to enable
support for VF610 device tree aware driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Without this change it is possible that Vybrid's NFC driver malloc() call
will obtain some memory used (and correctly free'd) by some previous
driver (in this case pinctrl for Vybrid).
As a result some fields of struct nfc - in out case mtd->_get_device - are
"pre initialized" with some random values.
On the latter stage of booting, when e.g. somebody calls 'mtdparts default'
the "data abort" is observed when __get_mtd_device() function is called.
The mtd->_get_device pointer is not NULL and wrong value is referenced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
board/ge/mx53ppd/mx53ppd.c: In function 'board_late_init':
board/ge/mx53ppd/mx53ppd.c:359:23: error: passing argument 2 of 'read_vpd' from incompatible pointer type [-Werror=incompatible-pointer-types]
res = read_vpd(&vpd, vpd_callback);
^~~~~~~~~~~~
In file included from board/ge/mx53ppd/mx53ppd.c:37:0:
board/ge/mx53ppd/../../ge/common/vpd_reader.h:19:5: note: expected 'int (*)(struct vpd_cache *, u8, u8, u8, size_t, const u8 *) {aka int (*)(struct vpd_cache *, unsigned char, unsigned char, unsigned char, unsigned int, const unsigned char *)}' but argument is of type 'int (*)(void *, u8, u8, u8, size_t, const u8 *) {aka int (*)(void *, unsigned char, unsigned char, unsigned char, unsigned int, const unsigned char *)}'
int read_vpd(struct vpd_cache *cache,
^~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Currently, U-Boot ignores the BBT stored in the last 4 blocks of NAND
flash because the NAND_BBT_USE_FLASH flag is not set. This leads to
two issues:
* U-Boot silently uses a memory-only BBT which is initialized with all
blocks marked as good. This means, actual bad blocks are marked good
and U-Boot might try writing to or reading from them.
* The BBT in flash, which will be created once Linux boots up, is not
off limits for a driver ontop, like UBI. While it does not seem to
consistently produce an error, sometimes UBI will fail to attach
because the BBT blocks obviously don't contain valid UBI data.
To fix this, this patch sets the CONFIG_SYS_NAND_USE_FLASH_BBT option,
which is used in ./drivers/mtd/nand/raw/mxs_nand.c to decide whether
a BBT in flash is used.
Signed-off-by: Harald Seiler <hws@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove unused DDRC register macros.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.
The boot log with Arm trusted firmware console enabled:
"
U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
PMIC: PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
NOTICE: Configureing TZASC380
NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty
NOTICE: BL31: Built : 09:28:54, Nov 8 2018
lpddr4 swffc start
NOTICE: sip svc init
U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM: 3 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Introduce DDR driver for i.MX8M. The driver will be used by SPL to
initialze DDR PHY and DDR Controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Introduce lpddr4 header file
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
No need to build bootaux in SPL stage
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
imximage.cfg will be used to generate the flash.bin
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Introduce script to generate fit image for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
