summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* board: mscc: luton: Update MSCC Luton boardHoratiu Vultur2019-05-031-2/+11
| | | | | | | Implement method board_phy_config to configure the external phys on the pcb90. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* net: mscc: luton: Update network driver for pcb90Horatiu Vultur2019-05-032-159/+258
| | | | | | | Update Luton network driver to have support also for pcb90. The pcb90 has 24 ports from which 12 ports are connected to SerDes6G. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* mips: rename mach-mt7620 to mach-mtmipsWeijie Gao2019-05-0317-20/+20
| | | | | | | | | | | | | | Currently mach-mt7620 contains only support for mt7628. To avoid confusion, rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms. MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628 because they do not share the same lowlevel codes. Dependencies of four drivers are changed to SOC_MT7628 as these drivers are only used by MT7628. Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
* net: mscc: ocelot: Update DTS for Ocelot pcb120.Horatiu Vultur2019-05-035-81/+167
| | | | | | Update device tree for ocelot to add support for ocelot pcb120. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* board: mscc: ocelot: Update MSCC Ocelot board.Horatiu Vultur2019-05-031-0/+15
| | | | | | Implement method board_phy_config to configure the phy for pcb120. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* net: mscc: ocelot: Update network driver for pcb120Horatiu Vultur2019-05-033-99/+338
| | | | | | Update Ocelot network driver to have support also for pcb120. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* arch: mips: Update initrd_start and initrd_endHoratiu Vultur2019-05-031-0/+2
| | | | | | | | | | | | | | | | | Microsemi SoC defines CONFIG_SYS_SDRAM_BASE to be 0x80000000, which represents the start of kseg0 and represents a virtual address. Meaning that the initrd_start and initrd_end point somewhere kseg0. When these parameters are passed to linux kernel through DT they are pointing somewhere in kseg0 which is a virtual address but linux kernel expects the addresses to be physical addresses(in kuseg) because it is converting the physical address to a virtual one. Therefore update the uboot to pass the physical address of initrd_start and initrd_end by converting them using the function virt_to_phys before setting up the DT. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* MSCC: delete obsolete reference to MSCC_BITBANG_SPI_GPIORobert P. J. Day2019-05-031-1/+0
| | | | | | | | | | | Remove "select MSCC_BITBANG_SPI_GPIO" since Kbuild option was deleted back in commit ace9c103df2875d2b435dbd7b36618020edfd1c0: commit ace9c103df2875d2b435dbd7b36618020edfd1c0 Author: Lars Povlsen <lars.povlsen@microchip.com> Date: Tue Jan 8 10:38:35 2019 +0100 mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
* configs: mscc_serval: Add network supportHoratiu Vultur2019-05-031-1/+5
| | | | | | Update default config to use network driver for Serval SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* net: mscc: serval: Add ethernet nodes for ServalHoratiu Vultur2019-05-034-0/+165
| | | | | | | Add ethernet nodes for Serval SoCs family. There are 2 pcb in this family: pcb105 and pcb106. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* board: mscc: serval: Update MSCC Serval boardsHoratiu Vultur2019-05-031-0/+12
| | | | | | | | In Serval SoC family there are 2 different pcb, both of them have the same phy, but with different version. Therefore implement board_phy_config and set all the phys in the same way. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* net: Add MSCC Serval network driver.Horatiu Vultur2019-05-033-0/+711
| | | | | | | | Add network driver for Microsemi Ethernet switch. It is present on Serval SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* board: mscc: serval: Fix board detectHoratiu Vultur2019-05-031-1/+1
| | | | | | | | When detecting the board, it was reading a register in the GPIO page of the phy and based on that value it was making a decision. The bug was that after the GPIO page for the first phy was set it was not reseted back. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* mips: mscc: serval: Fix resetHoratiu Vultur2019-05-032-26/+31
| | | | | | | | | In case the ddr training was failing, it couldn't reset, it was just hanging. Therefore reimplement it, so when ddr training is failing it would call _machine_restart, which power downs the DDR and does a force reset. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
* Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imxTom Rini2019-05-01111-832/+6447
|\ | | | | | | | | | | | | | | | | | | | | | | | | Porting to DM and i.MX8 ------------------------ - warp7 to DM - kp_imx53 to DM - Warnings in DT - MX8QM support - colibri-imx6ull to DM - imx7d-pico to DM - ocotp for MX8
| * colibri_imx6: use UUID for rootfsIgor Opaniuk2019-04-252-19/+40
| | | | | | | | | | | | | | | | | | | | 1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs partition. This fixes the issue, when MMC controllers are probed in a different order in U-boot and Linux kernel. 2. Fix legacy USB command (both sdboot and usbboot can be used now). Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * warp7: Switch to DM USBPierre-Jean Texier2019-04-254-6/+3
| | | | | | | | | | | | | | | | This commit switches to DM USB for warp7 and warp7_bl33 defconfigs. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * warp7: Switch to DM SerialPierre-Jean Texier2019-04-254-2/+8
| | | | | | | | | | | | | | | | This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * ddr: imx8m: hide i.MX8M DDR options from device driver entryPeng Fan2019-04-251-0/+4
| | | | | | | | | | | | | | Use one menu to hide the several i.MX8M DDR options from device driver entry. Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * ARM: dts: colibri-imx6ull: update device treeMarcel Ziswiler2019-04-251-39/+52
| | | | | | | | | | | | | | | | | | | | | | Fix compatible node to use regular Toradex notation. Annotate device tree with standard Colibri pin muxing comments. Use open-drain I2C pin muxings. Alphabetically re-order iomuxc nodes. Rename snvs-ad7879-int-grp touch interrupt node as per Linux device tree. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * ARM: dts: colibri-imx6ull: add osc32k_32k_out pinctrlMarcel Ziswiler2019-04-252-12/+16
| | | | | | | | | | | | | | | | Add GPIO1_IO03__OSC32K_32K_OUT pin muxing. While at it also fix indentation of pinfunc header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * ARM: dts: i.MX6Q: fix avoid_unnecessary_addr_size warningsMarcel Ziswiler2019-04-251-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Re-synced the device tree with Linux 5.0. This fixes the following warnings: w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@2/endpoint@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@2/endpoint@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@2/endpoint@2:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@2/endpoint@3:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@2/endpoint@4:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@3/endpoint@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@3/endpoint@2:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@3/endpoint@3:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (reg_format): /soc/ipu@2800000/ port@3/endpoint@4:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@0: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@0: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@1: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@1: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@2: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@2: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@3: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@3: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@4: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@2/endpoint@4: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@1: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@1: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@2: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@2: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@3: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@3: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@4: Relying on default #address-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_default_addr_size): /soc/ipu@2800000/port@3/endpoint@4: Relying on default #size-cells value w+arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size' Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
| * imx: Add variscite DART-6UL Evaluation KitParthiban Nallathambi2019-04-2513-0/+1008
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Port for the DART-6UL Evaluation Kit SBC. Based on the variscite DART-6UL iMX6ULL SoM. CPU: Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz) CPU: Commercial temperature grade (0C to 95C) at 43C Reset cause: POR Model: Variscite DART-6UL Evaluation Kit Board: Variscite DART-6UL Evaluation Kit DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial@02020000 Out: serial@02020000 Err: serial@02020000 Net: FEC0 Working: - Eth0 - i2c - MMC/SD - eMMC - USB host - UART 1 Note: LCDIF porting needs DM_VIDEO https://lists.denx.de/pipermail/u-boot/2019-April/365506.html Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
| * mxc_ocotp: Disable fuse sense for imx8mq B1Ye Li2019-04-251-0/+5
| | | | | | | | | | | | | | | | | | | | On iMX8MQ Rev B1, reading from fuse box is not allowed. The OCOTP_READ_FUSE_DATA register is tied to magic number 0xff0055aa for chip rev. So u-boot has to disable the fuse sense function for it. Signed-off-by: Ye Li <ye.li@nxp.com> Tested-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * mxc_ocotp: Update redundancy banks for mx7ulp B0Ye Li2019-04-251-7/+11
| | | | | | | | | | | | | | | | | | On mx7ulp B0, beside bank 0 and 1, the fuse bank 9, 10, 28 are changed to Redundancy mode not ECC, so they can support to program different bits of a word in multiple times. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * imx: i.MX8MQ: clear ocotp error bitPeng Fan2019-04-251-0/+7
| | | | | | | | | | | | In case ocotp error bit is set, clear it. Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * imx: 8qxp_mek: fix fdt_file and consolePeng Fan2019-04-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | Fix fdt_file and console to boot upstream Linux Kernel. Upstream linux use imx8qxp-mek.dtb, and pass lpuart32 to earlycon will not work for i.MX8QXP, only need to pass earlycon, check drivers/tty/serial/earlycon.c, " /* Just 'earlycon' is a valid param for devicetree and ACPI SPCR. */ " Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibrationLudwig Zenz2019-04-251-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | The four x16 DDR3 are wired in T-topology. From NXP AN4467: 'Although not required, T-Topologies may also benefit from performing Write Leveling as there are package delays on both the processor and DDR devices that can be de-skewed by performing Write Leveling. Therefore, Freescale recommends determining Write Leveling calibration parameters for all boards, regardless of topology used.' That is why write level calibration is also done. Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
| * ARM: imx6: update 1GB DDR3 calibration for DHCOM i.MX6qd PDKLudwig Zenz2019-04-251-12/+12
| | | | | | | | | | | | | | | | | | | | The existing calibration values were found to be incorrect in comparison to newly determined values. The new values were generated with the help of 5 boards. They have been determined with the NXP Utility 'DDR Stress Test (2.9.0)'. Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
| * imx: add lowlevel init for ARM64Peng Fan2019-04-252-1/+23
| | | | | | | | | | | | | | Sometimes we met SERROR, but only to catch it when Linux boots up. Let's enable catching in U-Boot to catch it ealier and ease debug. Signed-off-by: Peng Fan <peng.fan@nxp.com>
| * ARM: imx: Fix typo in select option for ZMX25Chris Packham2019-04-251-1/+1
| | | | | | | | | | | | | | | | Correct CPU_ARM926EJS1 to CPU_ARM926EJS. Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * warp7: Fix dfu_alt_info setting after DM conversionPierre-Jean Texier2019-04-251-1/+1
| | | | | | | | | | | | | | | | | | After DM conversion, U-Boot is larger than 512 KiB, so we need to increase the "size" of the dfu_alt_info setting. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Acked-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
| * dts: imx6ull: add USB aliases to support DMFilip Brozovic2019-04-251-0/+2
| | | | | | | | Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
| * imx8qxp_mek: drop warning due to unused variableStefano Babic2019-04-251-1/+0
| | | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
| * pico-imx7d: Increase u-boot size for dfu requestJoris Offouga2019-04-251-1/+1
| | | | | | | | | | | | | | | | After DM conversion, the size of U-Boot binary to increase. Previous size is 480K after DM Conversion the new size is 557K So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC. Signed-off-by: Joris Offouga <offougajoris@gmail.com>
| * pico-imx7d: Convert DM MMCJoris Offouga2019-04-256-38/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enable convert DM MMC for imx7d-pico board and variant. Before the DM conversion only usdhc3 was enabled and therefore it appeared as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2, which left unattended would drive changes to existing pico-pi bootscripts and environment variables that rely on mmc 0. Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will work unmodified. When converting to DM_MMC it is necessary that SPL initializes eMMC by itself, so move the original eMMC initialization from U-Boot proper to SPL. Signed-off-by: Joris Offouga <offougajoris@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
| * board: toradex: tdx-cfg-block: add new skusMarcel Ziswiler2019-04-252-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add all the latest new SKUs: - Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT - Apalis iMX8 QuadMax 4GB IT - Apalis iMX8 QuadPlus 2GB Wi-Fi / BT - Apalis iMX8 QuadPlus 2GB", - Colibri iMX8 QuadXPlus 2GB IT - Colibri iMX8 DualX 1GB Wi-Fi / Bluetooth - Colibri iMX8 DualX 1GB Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * pico-imx7d: defconfig Enable DM gpio pinctrl and pinctrl_imx7Joris Offouga2019-04-254-1/+12
| | | | | | | | | | | | | | | | | | This patch is necessary for convert this board to dm driver model DM GPIO requires gpio_request() to be called explicitly before doing any gpio operation Signed-off-by: Joris Offouga <offougajoris@gmail.com>
| * board: toradex: tdx-cfg-block: clean-up sku handlingMarcel Ziswiler2019-04-252-14/+20
| | | | | | | | | | | | | | Clean-up handling of several SKUs. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * pico-imx7d: defconfig: Add DT file hooksJoris Offouga2019-04-253-3/+6
| | | | | | | | | | | | This patch adds DT file hooks for Pico i.MX7D SOM and variant boards Signed-off-by: Joris Offouga <offougajoris@gmail.com>
| * arm: dts: imx8dx: add lpuart1, lpuart2, lpuart3Marcel Ziswiler2019-04-251-0/+54
| | | | | | | | | | | | | | | | Add support for lpuart1, lpuart2 and lpuart3. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * misc: imx8: remove duplicates from scfw apiMarcel Ziswiler2019-04-251-4/+0
| | | | | | | | | | | | | | | | Remove duplicate function declarations from the SCFW API header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * Arm: imx7d-pico: Import all Linux device tree for Pico i.MX7D SOMJoris Offouga2019-04-254-1/+788
| | | | | | | | | | | | | | | | This patch imports the Linux kernel base board imx7d-pico.dtsi, pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts from Linux v5.1-rc1. Signed-off-by: Joris Offouga <offougajoris@gmail.com>
| * ARM: dts: colibri-imx6ull: fix uart-has-rtscts propertyMarcel Ziswiler2019-04-251-2/+5
| | | | | | | | | | | | | | Remove vendor pre-fix fsl, from uart-has-rtscts property. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * colibri-imx6ull: migrate fec to using driver modelMarcel Ziswiler2019-04-253-21/+17
| | | | | | | | | | | | | | | | Migrate Ethernet FEC to using driver model. Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * colibri-imx6ull: migrate usb to using driver modelMarcel Ziswiler2019-04-253-48/+25
| | | | | | | | | | | | | | | | | | Migrate USB to using driver model. Add USBH_PEN GPIO regulator. While at it also add alias e.g. as required for UMS. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * colibri-imx6ull: migrate mmc to using driver modelMarcel Ziswiler2019-04-254-75/+17
| | | | | | | | | | | | | | | | | | | | Migrate MMC to using driver model. Migrate USDHC to using pinctrl. While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * colibri-imx6ull: migrate pinctrl and regulators to dtb/dmMarcel Ziswiler2019-04-252-77/+10
| | | | | | | | | | | | | | | | | | | | | | Migrate pinctrl and regulators to device tree resp. driver model: Ethernet, NAND and UART. Drop BOARD_EARLY_INIT_F as it is anyway no longer used. Enable CMD_DM, CMD_MTD, CMD_REGULATOR and DM_REGULATOR_FIXED. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * colibri-imx6ull: configuration clean-upMarcel Ziswiler2019-04-251-5/+3
| | | | | | | | | | | | | | | | | | | | Drop disabling SPL_SYS_THUMB_BUILD as we anyway do not use SPL. Enbale CRC32 verify, USB SDP and EFI loader support. Drop CMD_GPT and disabling RANDOM_UUID. Do savedefconfig which drops USB_FUNCTION_SDP. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
| * board: imx6ull: Add disable PMIC_STBY_REQPhilippe Schenker2019-04-251-0/+10
| | | | | | | | | | | | | | | | | | | | | | Disable output driver of PAD CCM_PMIC_STBY_REQ. This prevents the SOC to request for a lower voltage during sleep. This is necessary because the voltage is changing too slow for the SOC to wake up properly. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
View Lorry Controller Status