diff options
Diffstat (limited to 'include/configs/motionpro.h')
| -rw-r--r-- | include/configs/motionpro.h | 148 |
1 files changed, 74 insertions, 74 deletions
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index cae49de1a2..b3f16d5e7c 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -75,7 +75,7 @@ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_NETCONSOLE 1 /* network console */ #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } /* @@ -166,13 +166,13 @@ /* * Clock configuration: SYS_XTALIN = 33MHz */ -#define CFG_MPC5XXX_CLKIN 33000000 +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* * Set IPB speed to 100MHz */ -#define CFG_IPBCLK_EQUALS_XLBCLK +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* @@ -183,8 +183,8 @@ * Setting MBAR to otherwise will cause system hang when using SmartDMA such * as network commands. */ -#define CFG_MBAR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_MBAR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* * If building for running out of SDRAM, then MBAR has been set up beforehand @@ -192,61 +192,61 @@ * MBAR, as given in the doccumentation. */ #if TEXT_BASE == 0x00100000 -#define CFG_DEFAULT_MBAR 0xf0000000 +#define CONFIG_SYS_DEFAULT_MBAR 0xf0000000 #else /* TEXT_BASE != 0x00100000 */ -#define CFG_DEFAULT_MBAR 0x80000000 -#define CFG_LOWBOOT 1 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_LOWBOOT 1 #endif /* TEXT_BASE == 0x00100000 */ /* Use SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE -#define CFG_GBL_DATA_SIZE 128 /* size in bytes for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (256 << 10) /* 256 kB for Monitor */ -#define CFG_MALLOC_LEN (1024 << 10) /* 1 MiB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* 1 MiB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */ /* * Chip selects configuration */ /* Boot Chipselect */ -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x00045D00 +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00045D00 /* Flash memory addressing */ -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE -#define CFG_CS0_CFG CFG_BOOTCS_CFG +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_CFG CONFIG_SYS_BOOTCS_CFG /* Dual Port SRAM -- Kollmorgen Drive memory addressing */ -#define CFG_CS1_START 0x50000000 -#define CFG_CS1_SIZE 0x10000 -#define CFG_CS1_CFG 0x05055800 +#define CONFIG_SYS_CS1_START 0x50000000 +#define CONFIG_SYS_CS1_SIZE 0x10000 +#define CONFIG_SYS_CS1_CFG 0x05055800 /* Local register access */ -#define CFG_CS2_START 0x50010000 -#define CFG_CS2_SIZE 0x10000 -#define CFG_CS2_CFG 0x05055800 +#define CONFIG_SYS_CS2_START 0x50010000 +#define CONFIG_SYS_CS2_SIZE 0x10000 +#define CONFIG_SYS_CS2_CFG 0x05055800 /* Anybus CompactCom Module memory addressing */ -#define CFG_CS3_START 0x50020000 -#define CFG_CS3_SIZE 0x10000 -#define CFG_CS3_CFG 0x05055800 +#define CONFIG_SYS_CS3_START 0x50020000 +#define CONFIG_SYS_CS3_SIZE 0x10000 +#define CONFIG_SYS_CS3_CFG 0x05055800 /* No burst and dead cycle = 2 for all CSs */ -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x22222222 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x22222222 /* @@ -262,13 +262,13 @@ /* * Flash configuration */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 -#define CFG_FLASH_BASE 0xff000000 -#define CFG_FLASH_SIZE 0x01000000 -#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } -#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_BASE 0xff000000 +#define CONFIG_SYS_FLASH_SIZE 0x01000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ #define CONFIG_FLASH_16BIT /* Flash is 16-bit */ /* @@ -284,14 +284,14 @@ /* * IDE/ATA configuration */ -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA -#define CFG_IDE_MAXBUS 1 -#define CFG_IDE_MAXDEVICE 1 +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 1 #define CONFIG_IDE_PREINIT -#define CFG_ATA_DATA_OFFSET 0x0060 -#define CFG_ATA_REG_OFFSET CFG_ATA_DATA_OFFSET -#define CFG_ATA_STRIDE 4 +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 +#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET +#define CONFIG_SYS_ATA_STRIDE 4 #define CONFIG_DOS_PARTITION @@ -299,25 +299,25 @@ * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_MODULE 2 /* select I2C module #2 */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */ +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * EEPROM configuration */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ -#define CFG_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ +#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */ /* * RTC configuration */ #define CONFIG_RTC_DS1337 1 -#define CFG_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* @@ -354,7 +354,7 @@ extern void __led_set(led_id_t id, int state); */ #define CONFIG_ENV_IS_IN_FLASH 1 /* This has to be a multiple of the Flash sector size */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SIZE 0x1000 #define CONFIG_ENV_SECT_SIZE 0x20000 @@ -374,48 +374,48 @@ extern void __led_set(led_id_t id, int state); * Timer: CAN2/GPIO * PSC6/IRDA: GPIO (default) */ -#define CFG_GPS_PORT_CONFIG 0x1105a004 +#define CONFIG_SYS_GPS_PORT_CONFIG 0x1105a004 /* * Motion-PRO's CPLD revision control register */ -#define CPLD_REV_REGISTER (CFG_CS2_START + 0x06) +#define CPLD_REV_REGISTER (CONFIG_SYS_CS2_START + 0x06) /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x03e00000 /* 1 ... 62 MiB in DRAM */ -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x03e00000 /* 1 ... 62 MiB in DRAM */ +#define CONFIG_SYS_ALT_MEMTEST -#define CFG_LOAD_ADDR 0x200000 /* default kernel load addr */ +#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default kernel load addr */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* * Various low-level settings */ -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ /* Not needed for MPC 5xxx U-Boot, but used by tools/updater */ -#define CFG_RESET_ADDRESS 0xfff00100 +#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 |