diff options
Diffstat (limited to 'include/configs/hrcon.h')
| -rw-r--r-- | include/configs/hrcon.h | 614 |
1 files changed, 614 insertions, 0 deletions
diff --git a/include/configs/hrcon.h b/include/configs/hrcon.h new file mode 100644 index 0000000000..e7df9ad92a --- /dev/null +++ b/include/configs/hrcon.h @@ -0,0 +1,614 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83xx 1 /* MPC83xx family */ +#define CONFIG_MPC830x 1 /* MPC830x family */ +#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ +#define CONFIG_HRCON 1 /* HRCON board specific */ + +#define CONFIG_SYS_TEXT_BASE 0xFE000000 + +#define CONFIG_IDENT_STRING " hrcon 0.01" + +#define CONFIG_SYS_GENERIC_BOARD + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_LAST_STAGE_INIT + +/* new uImage format support */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 + +#define CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR +#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 + +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 + +#define CONFIG_CMD_FPGAD +#define CONFIG_CMD_IOLOOP + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.66MHz, then + * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz + * We choose the A type silicon as default, so the core is 400Mhz. + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_CORE_TO_CSB_3X1) +/* + * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits + * in 8308's HRCWH according to the manual, but original Freescale's + * code has them and I've expirienced some problems using the board + * with BDI3000 attached when I've tried to set these bits to zero + * (UART doesn't work after the 'reset run' command). + */ +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH (\ + SICRH_ESDHC_A_SD |\ + SICRH_ESDHC_B_SD |\ + SICRH_ESDHC_C_SD |\ + SICRH_GPIO_A_GPIO |\ + SICRH_GPIO_B_GPIO |\ + SICRH_IEEE1588_A_GPIO |\ + SICRH_USB |\ + SICRH_GTM_GPIO |\ + SICRH_IEEE1588_B_GPIO |\ + SICRH_ETSEC2_GPIO |\ + SICRH_GPIOSEL_1 |\ + SICRH_TMROBI_V3P3 |\ + SICRH_TSOBI1_V2P5 |\ + SICRH_TSOBI2_V2P5) /* 0x0037f103 */ +#define CONFIG_SYS_SICRL (\ + SICRL_SPI_PF0 |\ + SICRL_UART_PF0 |\ + SICRL_IRQ_PF0 |\ + SICRL_I2C2_PF0 |\ + SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */ + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * SERDES + */ +#define CONFIG_FSL_SERDES +#define CONFIG_FSL_SERDES1 0xe3000 + +/* + * Arbiter Setup + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of one chip NT5TU64M16HG from NANYA + */ + +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ + +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ODT_RD_NEVER \ + | CSCONFIG_ODT_WR_ONLY_CURRENT \ + | CSCONFIG_BANK_BIT_3 \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ +#define CONFIG_SYS_DDR_TIMING_3 0 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00260802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (7 << TIMING_CFG1_CASLAT_SHIFT) \ + | (9 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x26279222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (4 << TIMING_CFG2_CPO_SHIFT) \ + | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x021848c5 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x08240100 */ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_DBW_16) + /* 0x43100000 */ + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0242 << SDRAM_MODE_SD_SHIFT)) + /* ODT 150ohm CL=4, AL=0 on SDRAM */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x07f00000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +/* + * FLASH on the Local Bus + */ +#if 1 +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_FLASH_CFI_LEGACY +#define CONFIG_SYS_FLASH_LEGACY_512Kx16 +#else +#define CONFIG_SYS_NO_FLASH +#endif + +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ + +/* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) + +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ + | BR_PS_16 /* 16 bit port */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * FPGA + */ +#define CONFIG_SYS_FPGA0_BASE 0xE0600000 +#define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ + +/* Window base at FPGA base */ +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) + +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ + | BR_PS_16 /* 16 bit port */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET) + +#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE +#define CONFIG_SYS_FPGA_DONE(k) 0x0010 + +#define CONFIG_SYS_FPGA_COUNT 1 + +#define CONFIG_SYS_MCLINK_MAX 3 + +#define CONFIG_SYS_FPGA_PTR \ + { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 2 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 + +#define CONFIG_PCA953X /* NXP PCA9554 */ +#define CONFIG_PCA9698 /* NXP PCA9698 */ + +#define CONFIG_SYS_I2C_IHS +#define CONFIG_SYS_I2C_IHS_CH0 +#define CONFIG_SYS_I2C_IHS_SPEED_0 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_IHS_CH1 +#define CONFIG_SYS_I2C_IHS_SPEED_1 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F +#define CONFIG_SYS_I2C_IHS_CH2 +#define CONFIG_SYS_I2C_IHS_SPEED_2 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F +#define CONFIG_SYS_I2C_IHS_CH3 +#define CONFIG_SYS_I2C_IHS_SPEED_3 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ +#define CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F +#define I2C_SOFT_DECLARATIONS2 +#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F +#define I2C_SOFT_DECLARATIONS3 +#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F +#define I2C_SOFT_DECLARATIONS4 +#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F + +#define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8} +#define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8} +#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} + +#ifndef __ASSEMBLY__ +void fpga_gpio_set(unsigned int bus, int pin); +void fpga_gpio_clear(unsigned int bus, int pin); +int fpga_gpio_get(unsigned int bus, int pin); +#endif + +#define I2C_ACTIVE { } +#define I2C_TRISTATE { } +#define I2C_READ \ + (fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \ + else \ + fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \ + else \ + fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \ + } while (0) +#define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ + +/* + * Software (bit-bang) MII driver configuration + */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +#define CONFIG_BITBANGMII_MULTI + +/* + * OSD Setup + */ +#define CONFIG_SYS_OSD_SCREENS 1 +#define CONFIG_SYS_DP501_DIFFERENTIAL +#define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +/* enable PCIE clock */ +#define CONFIG_SYS_SCCR_PCIEXP1CM 1 + +#define CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC0" + +/* + * Environment + */ +#if 1 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#else +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +#undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */ +#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */ +#define CONFIG_AUTOBOOT_STOP_STR " " + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ + BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ + BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define CONFIG_HOSTNAME hrcon +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS1\0" \ + "u-boot=u-boot.bin\0" \ + "kernel_addr=1000000\0" \ + "fdt_addr=C00000\0" \ + "fdtfile=hrcon.dtb\0" \ + "load=tftp ${loadaddr} ${u-boot}\0" \ + "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ + " +${filesize};cp.b ${fileaddr} " \ + __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ + "upd=run load update\0" \ + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp ${kernel_addr} $bootfile;" \ + "tftp ${fdt_addr} $fdtfile;" \ + "bootm ${kernel_addr} - ${fdt_addr}" + +#define CONFIG_MMCBOOTCOMMAND \ + "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ + "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ + "bootm ${kernel_addr} - ${fdt_addr}" + +#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND + + +#endif /* __CONFIG_H */ |