diff options
Diffstat (limited to 'board/freescale')
66 files changed, 965 insertions, 296 deletions
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 34d66d5fd2..bed8f56be4 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -1110,7 +1110,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -1136,6 +1136,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } /* diff --git a/board/freescale/bsc9131rdb/bsc9131rdb.c b/board/freescale/bsc9131rdb/bsc9131rdb.c index 9146f49262..75e114217b 100644 --- a/board/freescale/bsc9131rdb/bsc9131rdb.c +++ b/board/freescale/bsc9131rdb/bsc9131rdb.c @@ -58,7 +58,7 @@ struct node_info nodes[] = { { "fsl,ifc-nand", MTD_DEV_TYPE_NAND, }, }; #endif -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -74,5 +74,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif fdt_fixup_dr_usb(blob, bd); + + return 0; } #endif diff --git a/board/freescale/bsc9132qds/bsc9132qds.c b/board/freescale/bsc9132qds/bsc9132qds.c index c88838b3df..36a68dbc4d 100644 --- a/board/freescale/bsc9132qds/bsc9132qds.c +++ b/board/freescale/bsc9132qds/bsc9132qds.c @@ -363,7 +363,7 @@ struct node_info nodes[] = { { "fsl,ifc-nand", MTD_DEV_TYPE_NAND, }, }; #endif -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -423,5 +423,7 @@ void ft_board_setup(void *blob, bd_t *bd) printf("\nRemove sim from hwconfig and reset\n"); } } + + return 0; } #endif diff --git a/board/freescale/c29xpcie/c29xpcie.c b/board/freescale/c29xpcie/c29xpcie.c index 534c6d11b0..d75770969b 100644 --- a/board/freescale/c29xpcie/c29xpcie.c +++ b/board/freescale/c29xpcie/c29xpcie.c @@ -128,7 +128,7 @@ void fdt_del_sec(void *blob, int offset) } } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -150,5 +150,7 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_del_sec(blob, 1); else if (cpu->soc_ver == SVR_C292) fdt_del_sec(blob, 2); + + return 0; } #endif diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 32b5a3b70c..25a1bc1a0f 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -53,6 +53,7 @@ obj-$(CONFIG_P5040DS) += ics307_clk.o obj-$(CONFIG_VSC_CROSSBAR) += vsc3316_3308.o obj-$(CONFIG_IDT8T49N222A) += idt8t49n222a_serdes_clk.o obj-$(CONFIG_ZM7300) += zm7300.o +obj-$(CONFIG_POWER_PFUZE100) += pfuze.o # deal with common files for P-series corenet based devices obj-$(CONFIG_P2041RDB) += p_corenet/ diff --git a/board/freescale/common/cds_pci_ft.c b/board/freescale/common/cds_pci_ft.c index 2e5dcdf0e2..571dfbbaad 100644 --- a/board/freescale/common/cds_pci_ft.c +++ b/board/freescale/common/cds_pci_ft.c @@ -63,13 +63,14 @@ static void cds_pci_fixup(void *blob) } } -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); cds_pci_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c new file mode 100644 index 0000000000..2cd1794429 --- /dev/null +++ b/board/freescale/common/pfuze.c @@ -0,0 +1,54 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> + +struct pmic *pfuze_common_init(unsigned char i2cbus) +{ + struct pmic *p; + int ret; + unsigned int reg; + + ret = power_pfuze100_init(i2cbus); + if (ret) + return NULL; + + p = pmic_get("PFUZE100"); + ret = pmic_probe(p); + if (ret) + return NULL; + + pmic_reg_read(p, PFUZE100_DEVICEID, ®); + printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + + /* Set SW1AB stanby volage to 0.975V */ + pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); + reg &= ~SW1x_STBY_MASK; + reg |= SW1x_0_975V; + pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); + + /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PUZE_100_SW1ABCONF, ®); + reg &= ~SW1xCONF_DVSSPEED_MASK; + reg |= SW1xCONF_DVSSPEED_4US; + pmic_reg_write(p, PUZE_100_SW1ABCONF, reg); + + /* Set SW1C standby voltage to 0.975V */ + pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); + reg &= ~SW1x_STBY_MASK; + reg |= SW1x_0_975V; + pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); + + /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PFUZE100_SW1CCONF, ®); + reg &= ~SW1xCONF_DVSSPEED_MASK; + reg |= SW1xCONF_DVSSPEED_4US; + pmic_reg_write(p, PFUZE100_SW1CCONF, reg); + + return p; +} diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h new file mode 100644 index 0000000000..7a4126cca0 --- /dev/null +++ b/board/freescale/common/pfuze.h @@ -0,0 +1,12 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __PFUZE_BOARD_HELPER__ +#define __PFUZE_BOARD_HELPER__ + +struct pmic *pfuze_common_init(unsigned char i2cbus); + +#endif diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c index 3426b8ada3..5cb7570c8b 100644 --- a/board/freescale/common/sys_eeprom.c +++ b/board/freescale/common/sys_eeprom.c @@ -114,7 +114,7 @@ static void show_eeprom(void) e.date[3] & 0x80 ? "PM" : ""); /* Show MAC addresses */ - for (i = 0; i < min(e.mac_count, MAX_NUM_PORTS); i++) { + for (i = 0; i < min(e.mac_count, (u8)MAX_NUM_PORTS); i++) { u8 *p = e.mac[i]; @@ -223,7 +223,7 @@ static int prog_eeprom(void) */ for (i = 0, p = &e; i < sizeof(e); i += 8, p += 8) { ret = i2c_write(CONFIG_SYS_I2C_EEPROM_ADDR, i, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, - p, min((sizeof(e) - i), 8)); + p, min((int)(sizeof(e) - i), 8)); if (ret) break; udelay(5000); /* 5ms write cycle timing */ @@ -461,7 +461,7 @@ int mac_read_from_eeprom(void) memset(e.mac[8], 0xff, 6); #endif - for (i = 0; i < min(e.mac_count, MAX_NUM_PORTS); i++) { + for (i = 0; i < min(e.mac_count, (u8)MAX_NUM_PORTS); i++) { if (memcmp(&e.mac[i], "\0\0\0\0\0\0", 6) && memcmp(&e.mac[i], "\xFF\xFF\xFF\xFF\xFF\xFF", 6)) { char ethaddr[18]; diff --git a/board/freescale/corenet_ds/corenet_ds.c b/board/freescale/corenet_ds/corenet_ds.c index 65b386741e..6f0fea1a35 100644 --- a/board/freescale/corenet_ds/corenet_ds.c +++ b/board/freescale/corenet_ds/corenet_ds.c @@ -190,7 +190,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -213,4 +213,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c index d64b24c417..0a7720a001 100644 --- a/board/freescale/ls1021aqds/ls1021aqds.c +++ b/board/freescale/ls1021aqds/ls1021aqds.c @@ -254,9 +254,11 @@ int board_init(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + + return 0; } u8 flash_read8(void *addr) diff --git a/board/freescale/ls1021atwr/ls1021atwr.c b/board/freescale/ls1021atwr/ls1021atwr.c index 3f2dc1acad..3e8c37b05d 100644 --- a/board/freescale/ls1021atwr/ls1021atwr.c +++ b/board/freescale/ls1021atwr/ls1021atwr.c @@ -303,9 +303,11 @@ int misc_init_r(void) } #endif -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + + return 0; } u8 flash_read8(void *addr) diff --git a/board/freescale/ls2085a/ls2085a.c b/board/freescale/ls2085a/ls2085a.c index 2c79a7181e..163a4c486a 100644 --- a/board/freescale/ls2085a/ls2085a.c +++ b/board/freescale/ls2085a/ls2085a.c @@ -100,7 +100,7 @@ void fdt_fixup_board_enet(void *fdt) #endif #ifdef CONFIG_OF_BOARD_SETUP -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -115,5 +115,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_MC_ENET fdt_fixup_board_enet(blob); #endif + + return 0; } #endif diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c index 940978e649..40bd55dfba 100644 --- a/board/freescale/mpc5121ads/mpc5121ads.c +++ b/board/freescale/mpc5121ads/mpc5121ads.c @@ -275,8 +275,10 @@ int checkboard (void) } #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); + + return 0; } #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/freescale/mpc7448hpc2/mpc7448hpc2.c b/board/freescale/mpc7448hpc2/mpc7448hpc2.c index 71b760c4a9..11747ca4a4 100644 --- a/board/freescale/mpc7448hpc2/mpc7448hpc2.c +++ b/board/freescale/mpc7448hpc2/mpc7448hpc2.c @@ -70,11 +70,12 @@ phys_size_t initdram (int board_type) } #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); + + return 0; } #endif diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c index fba41fe504..93e1c50f39 100644 --- a/board/freescale/mpc8308rdb/mpc8308rdb.c +++ b/board/freescale/mpc8308rdb/mpc8308rdb.c @@ -161,11 +161,13 @@ int misc_init_r(void) return 0; } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); fdt_fixup_dr_usb(blob, bd); fdt_fixup_esdhc(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc8313erdb/mpc8313erdb.c b/board/freescale/mpc8313erdb/mpc8313erdb.c index 69e98a5007..eac193e817 100644 --- a/board/freescale/mpc8313erdb/mpc8313erdb.c +++ b/board/freescale/mpc8313erdb/mpc8313erdb.c @@ -116,12 +116,14 @@ int misc_init_r(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif #else /* CONFIG_SPL_BUILD */ diff --git a/board/freescale/mpc8315erdb/mpc8315erdb.c b/board/freescale/mpc8315erdb/mpc8315erdb.c index e6f091fd2f..ed611c56c3 100644 --- a/board/freescale/mpc8315erdb/mpc8315erdb.c +++ b/board/freescale/mpc8315erdb/mpc8315erdb.c @@ -188,7 +188,7 @@ void fdt_tsec1_fixup(void *fdt, bd_t *bd) do_fixup_by_path(fdt, path, "status", disabled, sizeof(disabled), 1); } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI @@ -196,6 +196,8 @@ void ft_board_setup(void *blob, bd_t *bd) #endif fdt_fixup_dr_usb(blob, bd); fdt_tsec1_fixup(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc8323erdb/mpc8323erdb.c b/board/freescale/mpc8323erdb/mpc8323erdb.c index 3dce3623a4..0a0152ad9e 100644 --- a/board/freescale/mpc8323erdb/mpc8323erdb.c +++ b/board/freescale/mpc8323erdb/mpc8323erdb.c @@ -172,12 +172,14 @@ void pci_init_board(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc832xemds/mpc832xemds.c b/board/freescale/mpc832xemds/mpc832xemds.c index b7ea0e44c3..adf425486e 100644 --- a/board/freescale/mpc832xemds/mpc832xemds.c +++ b/board/freescale/mpc832xemds/mpc832xemds.c @@ -154,11 +154,13 @@ int checkboard(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8349emds/mpc8349emds.c b/board/freescale/mpc8349emds/mpc8349emds.c index d9092201aa..02b5040ef4 100644 --- a/board/freescale/mpc8349emds/mpc8349emds.c +++ b/board/freescale/mpc8349emds/mpc8349emds.c @@ -273,11 +273,13 @@ void spi_cs_deactivate(struct spi_slave *slave) #endif /* CONFIG_HARD_SPI */ #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8349itx/mpc8349itx.c b/board/freescale/mpc8349itx/mpc8349itx.c index 803d722806..22a1d99c88 100644 --- a/board/freescale/mpc8349itx/mpc8349itx.c +++ b/board/freescale/mpc8349itx/mpc8349itx.c @@ -378,11 +378,13 @@ int misc_init_r(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI ft_pci_setup(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8360emds/mpc8360emds.c b/board/freescale/mpc8360emds/mpc8360emds.c index 5ff9dff587..f0a55f8a8d 100644 --- a/board/freescale/mpc8360emds/mpc8360emds.c +++ b/board/freescale/mpc8360emds/mpc8360emds.c @@ -402,7 +402,7 @@ static void ft_board_fixup_qe_usb(void *blob, bd_t *bd) "peripheral", sizeof("peripheral"), 1); } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); #ifdef CONFIG_PCI @@ -447,5 +447,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif } } + + return 0; } #endif diff --git a/board/freescale/mpc8360erdk/mpc8360erdk.c b/board/freescale/mpc8360erdk/mpc8360erdk.c index fef230bfbd..478f8205a9 100644 --- a/board/freescale/mpc8360erdk/mpc8360erdk.c +++ b/board/freescale/mpc8360erdk/mpc8360erdk.c @@ -340,9 +340,11 @@ void pci_init_board(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); ft_pci_setup(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c index c749e5553a..572913c7ac 100644 --- a/board/freescale/mpc837xemds/mpc837xemds.c +++ b/board/freescale/mpc837xemds/mpc837xemds.c @@ -328,7 +328,7 @@ static void ft_pci_fixup(void *blob, bd_t *bd) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); ft_tsec_fixup(blob, bd); @@ -340,5 +340,7 @@ void ft_board_setup(void *blob, bd_t *bd) ft_pci_fixup(blob, bd); ft_pcie_fixup(blob, bd); #endif + + return 0; } #endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/freescale/mpc837xerdb/mpc837xerdb.c b/board/freescale/mpc837xerdb/mpc837xerdb.c index 9afdcaf7ae..e0a1031380 100644 --- a/board/freescale/mpc837xerdb/mpc837xerdb.c +++ b/board/freescale/mpc837xerdb/mpc837xerdb.c @@ -199,7 +199,7 @@ int misc_init_r(void) #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { #ifdef CONFIG_PCI ft_pci_setup(blob, bd); @@ -207,5 +207,7 @@ void ft_board_setup(void *blob, bd_t *bd) ft_cpu_setup(blob, bd); fdt_fixup_dr_usb(blob, bd); fdt_fixup_esdhc(blob, bd); + + return 0; } #endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/freescale/mpc8536ds/mpc8536ds.c b/board/freescale/mpc8536ds/mpc8536ds.c index 93eed59b1a..7b0f461971 100644 --- a/board/freescale/mpc8536ds/mpc8536ds.c +++ b/board/freescale/mpc8536ds/mpc8536ds.c @@ -271,7 +271,7 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); @@ -285,5 +285,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_dr_usb(blob, bd); #endif + return 0; } #endif diff --git a/board/freescale/mpc8540ads/mpc8540ads.c b/board/freescale/mpc8540ads/mpc8540ads.c index 93288c7e9c..1069e2c8c8 100644 --- a/board/freescale/mpc8540ads/mpc8540ads.c +++ b/board/freescale/mpc8540ads/mpc8540ads.c @@ -218,8 +218,7 @@ pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { int node, tmp[2]; const char *path; @@ -237,5 +236,7 @@ ft_board_setup(void *blob, bd_t *bd) } #endif } + + return 0; } #endif diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c index 1b33db6f31..66fb228a90 100644 --- a/board/freescale/mpc8544ds/mpc8544ds.c +++ b/board/freescale/mpc8544ds/mpc8544ds.c @@ -305,7 +305,7 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); @@ -314,5 +314,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8560ads/mpc8560ads.c b/board/freescale/mpc8560ads/mpc8560ads.c index 7104e33156..f99d639b2f 100644 --- a/board/freescale/mpc8560ads/mpc8560ads.c +++ b/board/freescale/mpc8560ads/mpc8560ads.c @@ -438,8 +438,7 @@ pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { int node, tmp[2]; const char *path; @@ -457,5 +456,7 @@ ft_board_setup(void *blob, bd_t *bd) } #endif } + + return 0; } #endif diff --git a/board/freescale/mpc8568mds/mpc8568mds.c b/board/freescale/mpc8568mds/mpc8568mds.c index a8fdcb5f91..a5c5d9dd1a 100644 --- a/board/freescale/mpc8568mds/mpc8568mds.c +++ b/board/freescale/mpc8568mds/mpc8568mds.c @@ -345,10 +345,12 @@ void pci_init_board(void) #endif /* CONFIG_PCI */ #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); FT_FSL_PCI_SETUP; + + return 0; } #endif diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c index cb55e1c98c..836578f3cb 100644 --- a/board/freescale/mpc8569mds/mpc8569mds.c +++ b/board/freescale/mpc8569mds/mpc8569mds.c @@ -514,7 +514,7 @@ void pci_init_board(void) #endif /* CONFIG_PCI */ #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { #if defined(CONFIG_SYS_UCC_RMII_MODE) int nodeoff, off, err; @@ -579,5 +579,7 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_board_fixup_esdhc(blob, bd); fdt_board_fixup_qe_uart(blob, bd); fdt_board_fixup_qe_usb(blob, bd); + + return 0; } #endif diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c index 1bbf832148..3f68cf496a 100644 --- a/board/freescale/mpc8572ds/mpc8572ds.c +++ b/board/freescale/mpc8572ds/mpc8572ds.c @@ -232,7 +232,7 @@ int board_eth_init(bd_t *bis) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -249,5 +249,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c index d8740ddacc..95e398c9f4 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd.c @@ -258,12 +258,13 @@ void pci_init_board(void) } #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); FT_FSL_PCI_SETUP; + + return 0; } #endif diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index a58b5f9cd4..94633b5c99 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -119,12 +119,11 @@ void pci_init_board(void) #if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { int off; u64 *tmp; - u32 *addrcells; + int addrcells; ft_cpu_setup(blob, bd); @@ -136,12 +135,13 @@ ft_board_setup(void *blob, bd_t *bd) * which is defined by the "reg" property in the soc node. */ off = fdt_path_offset(blob, "/soc8641"); - addrcells = (u32 *)fdt_getprop(blob, 0, "#address-cells", NULL); + addrcells = fdt_address_cells(blob, 0); tmp = (u64 *)fdt_getprop(blob, off, "reg", NULL); if (tmp) { u64 addr; - if (addrcells && (*addrcells == 1)) + + if (addrcells == 1) addr = *(u32 *)tmp; else addr = *tmp; @@ -152,6 +152,8 @@ ft_board_setup(void *blob, bd_t *bd) "in u-boot. This means your .dts might " "be old.\n"); } + + return 0; } #endif diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 9b43c84e79..f1e5eb433a 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -320,7 +320,7 @@ int board_mmc_init(bd_t *bis) }; u32 index; - s32 status = 0; + int ret; esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); @@ -340,11 +340,13 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more ESDHC controller" "(%d) as supported by the board(2)\n", CONFIG_SYS_FSL_ESDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + if (ret) + return ret; } - return status; + return 0; } #endif diff --git a/board/freescale/mx53ard/mx53ard.c b/board/freescale/mx53ard/mx53ard.c index c960c44a61..8ba27288e3 100644 --- a/board/freescale/mx53ard/mx53ard.c +++ b/board/freescale/mx53ard/mx53ard.c @@ -166,7 +166,7 @@ int board_mmc_init(bd_t *bis) }; u32 index; - s32 status = 0; + int ret; esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); @@ -185,12 +185,14 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more ESDHC controller" "(%d) as supported by the board(2)\n", CONFIG_SYS_FSL_ESDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + if (ret) + return ret; } - return status; + return 0; } #endif diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c index 13519e26da..6ee6d73ed2 100644 --- a/board/freescale/mx53evk/mx53evk.c +++ b/board/freescale/mx53evk/mx53evk.c @@ -195,7 +195,7 @@ int board_mmc_init(bd_t *bis) }; u32 index; - s32 status = 0; + int ret; esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); @@ -214,12 +214,14 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more ESDHC controller" "(%d) as supported by the board(2)\n", CONFIG_SYS_FSL_ESDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + if (ret) + return ret; } - return status; + return 0; } #endif diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c index 7569ded8d8..efcf4b390d 100644 --- a/board/freescale/mx53loco/mx53loco.c +++ b/board/freescale/mx53loco/mx53loco.c @@ -186,7 +186,7 @@ int board_mmc_init(bd_t *bis) }; u32 index; - s32 status = 0; + int ret; esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); @@ -205,12 +205,14 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more ESDHC controller" "(%d) as supported by the board(2)\n", CONFIG_SYS_FSL_ESDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + if (ret) + return ret; } - return status; + return 0; } #endif diff --git a/board/freescale/mx53smd/mx53smd.c b/board/freescale/mx53smd/mx53smd.c index d64c674e91..0963fd7b43 100644 --- a/board/freescale/mx53smd/mx53smd.c +++ b/board/freescale/mx53smd/mx53smd.c @@ -106,7 +106,7 @@ int board_mmc_init(bd_t *bis) }; u32 index; - s32 status = 0; + int ret; esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); @@ -121,12 +121,14 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more ESDHC controller" "(%d) as supported by the board(1)\n", CONFIG_SYS_FSL_ESDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]); + if (ret) + return ret; } - return status; + return 0; } #endif diff --git a/board/freescale/mx6qarm2/mx6qarm2.c b/board/freescale/mx6qarm2/mx6qarm2.c index 667dca532f..3a5b26dde7 100644 --- a/board/freescale/mx6qarm2/mx6qarm2.c +++ b/board/freescale/mx6qarm2/mx6qarm2.c @@ -125,7 +125,7 @@ int board_mmc_getcd(struct mmc *mmc) int board_mmc_init(bd_t *bis) { - s32 status = 0; + int ret; u32 index = 0; usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); @@ -145,13 +145,15 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more USDHC controllers" "(%d) then supported by the board (%d)\n", index + 1, CONFIG_SYS_FSL_USDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]); + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]); + if (ret) + return ret; } - return status; + return 0; } #endif diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index c35dcaf3cf..59387ffaaa 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -28,6 +28,8 @@ #include <asm/imx-common/video.h> #include <asm/arch/crm_regs.h> #include <pca953x.h> +#include <power/pmic.h> +#include "../common/pfuze.h" DECLARE_GLOBAL_DATA_PTR; @@ -53,6 +55,12 @@ DECLARE_GLOBAL_DATA_PTR; #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define I2C_PMIC 1 + int dram_init(void) { gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); @@ -97,6 +105,7 @@ static struct i2c_pads_info i2c_pad_info1 = { } }; +#ifndef CONFIG_SYS_FLASH_CFI /* * I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor, * Compass Sensor, Accelerometer, Res Touch @@ -113,6 +122,7 @@ static struct i2c_pads_info i2c_pad_info2 = { .gp = IMX_GPIO_NR(3, 18) } }; +#endif static iomux_v3_cfg_t const i2c3_pads[] = { MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), @@ -160,6 +170,75 @@ static int port_exp_direction_output(unsigned gpio, int value) return 0; } +static iomux_v3_cfg_t const eimnor_pads[] = { + MX6_PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D17__EIM_DATA17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D18__EIM_DATA18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D19__EIM_DATA19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D20__EIM_DATA20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D21__EIM_DATA21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D22__EIM_DATA22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D23__EIM_DATA23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D24__EIM_DATA24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D25__EIM_DATA25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D26__EIM_DATA26 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D27__EIM_DATA27 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D28__EIM_DATA28 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D29__EIM_DATA29 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D30__EIM_DATA30 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_D31__EIM_DATA31 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA0__EIM_AD00 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA1__EIM_AD01 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA2__EIM_AD02 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA3__EIM_AD03 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA4__EIM_AD04 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA5__EIM_AD05 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA6__EIM_AD06 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA7__EIM_AD07 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA8__EIM_AD08 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA9__EIM_AD09 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA10__EIM_AD10 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA11__EIM_AD11 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL) , + MX6_PAD_EIM_DA12__EIM_AD12 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA13__EIM_AD13 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA14__EIM_AD14 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_DA15__EIM_AD15 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A16__EIM_ADDR16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A17__EIM_ADDR17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A18__EIM_ADDR18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A19__EIM_ADDR19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A20__EIM_ADDR20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A21__EIM_ADDR21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A22__EIM_ADDR22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_A23__EIM_ADDR23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL), + MX6_PAD_EIM_OE__EIM_OE_B | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_EIM_RW__EIM_RW | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_EIM_CS0__EIM_CS0_B | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void eimnor_cs_setup(void) +{ + struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR; + + writel(0x00020181, &weim_regs->cs0gcr1); + writel(0x00000001, &weim_regs->cs0gcr2); + writel(0x0a020000, &weim_regs->cs0rcr1); + writel(0x0000c000, &weim_regs->cs0rcr2); + writel(0x0804a240, &weim_regs->cs0wcr1); + writel(0x00000120, &weim_regs->wcr); + + set_chipselect_size(CS0_128); +} + +static void setup_iomux_eimnor(void) +{ + imx_iomux_v3_setup_multiple_pads(eimnor_pads, ARRAY_SIZE(eimnor_pads)); + + gpio_direction_output(IMX_GPIO_NR(5, 4), 0); + + eimnor_cs_setup(); +} + static void setup_iomux_enet(void) { imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); @@ -402,6 +481,7 @@ int board_early_init_f(void) #ifdef CONFIG_NAND_MXS setup_gpmi_nand(); #endif + return 0; } @@ -415,11 +495,13 @@ int board_init(void) /* I2C 3 Steer */ gpio_direction_output(IMX_GPIO_NR(5, 4), 1); imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads)); +#ifndef CONFIG_SYS_FLASH_CFI setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); - +#endif gpio_direction_output(IMX_GPIO_NR(1, 15), 1); imx_iomux_v3_setup_multiple_pads(port_exp, ARRAY_SIZE(port_exp)); + setup_iomux_eimnor(); return 0; } @@ -430,6 +512,17 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs) } #endif +int power_init_board(void) +{ + struct pmic *p; + + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; + + return 0; +} + #ifdef CONFIG_CMD_BMODE static const struct boot_mode board_boot_modes[] = { /* 4 bit bus width */ diff --git a/board/freescale/mx6sabresd/MAINTAINERS b/board/freescale/mx6sabresd/MAINTAINERS index 69c0a3065f..0011ec7b49 100644 --- a/board/freescale/mx6sabresd/MAINTAINERS +++ b/board/freescale/mx6sabresd/MAINTAINERS @@ -5,3 +5,4 @@ F: board/freescale/mx6sabresd/ F: include/configs/mx6sabresd.h F: configs/mx6dlsabresd_defconfig F: configs/mx6qsabresd_defconfig +F: configs/mx6sabresd_spl_defconfig diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 1142e8a27e..ac3757f074 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -27,12 +27,11 @@ #include <i2c.h> #include <power/pmic.h> #include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" #include <asm/arch/mx6-ddr.h> DECLARE_GLOBAL_DATA_PTR; -#define BOOT_CFG 0x020D8004 - #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) @@ -300,7 +299,8 @@ int board_mmc_init(bd_t *bis) return 0; #else - unsigned reg = readl(BOOT_CFG) >> 11; + struct src *psrc = (struct src *)SRC_BASE_ADDR; + unsigned reg = readl(&psrc->sbmr1) >> 11; /* * Upon reading BOOT_CFG register the following map is done: * Bit 11 and 12 of BOOT_CFG register can determine the current @@ -560,60 +560,27 @@ int board_init(void) return 0; } -static int pfuze_init(void) +int power_init_board(void) { struct pmic *p; - int ret; unsigned int reg; - ret = power_pfuze100_init(I2C_PMIC); - if (ret) - return ret; - - p = pmic_get("PFUZE100"); - ret = pmic_probe(p); - if (ret) - return ret; - - pmic_reg_read(p, PFUZE100_DEVICEID, ®); - printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; /* Increase VGEN3 from 2.5 to 2.8V */ pmic_reg_read(p, PFUZE100_VGEN3VOL, ®); - reg &= ~0xf; - reg |= 0xa; + reg &= ~LDO_VOL_MASK; + reg |= LDOB_2_80V; pmic_reg_write(p, PFUZE100_VGEN3VOL, reg); /* Increase VGEN5 from 2.8 to 3V */ pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); - reg &= ~0xf; - reg |= 0xc; + reg &= ~LDO_VOL_MASK; + reg |= LDOB_3_00V; pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); - /* Set SW1AB stanby volage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); - - /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PUZE_100_SW1ABCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PUZE_100_SW1ABCONF, reg); - - /* Set SW1C standby voltage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); - - /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PFUZE100_SW1CCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PFUZE100_SW1CCONF, reg); - return 0; } @@ -640,8 +607,6 @@ int board_late_init(void) #ifdef CONFIG_CMD_BMODE add_board_boot_modes(board_boot_modes); #endif - pfuze_init(); - return 0; } @@ -729,11 +694,33 @@ static struct mx6_ddr3_cfg mem_ddr = { .trasmin = 3500, }; +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0x00C03F3F, &ccm->CCGR0); + writel(0x0030FC03, &ccm->CCGR1); + writel(0x0FFFC000, &ccm->CCGR2); + writel(0x3FF00000, &ccm->CCGR3); + writel(0x00FFF300, &ccm->CCGR4); + writel(0x0F0000C3, &ccm->CCGR5); + writel(0x000003FF, &ccm->CCGR6); +} + +static void gpr_init(void) +{ + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* enable AXI cache for VDOA/VPU/IPU */ + writel(0xF00000CF, &iomux->gpr[4]); + /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ + writel(0x007F007F, &iomux->gpr[6]); + writel(0x007F007F, &iomux->gpr[7]); +} + /* - * This section require the differentiation - * between iMX6 Sabre Families. - * But for now, it will configure only for - * SabreSD. + * This section requires the differentiation between iMX6 Sabre boards, but + * for now, it will configure only for the mx6q variant. */ static void spl_dram_init(void) { @@ -768,6 +755,9 @@ void board_init_f(ulong dummy) /* setup AIPS and disable watchdog */ arch_cpu_init(); + ccgr_init(); + gpr_init(); + /* iomux and setup of i2c */ board_early_init_f(); diff --git a/board/freescale/mx6sabresd/mx6sabresd_spl.cfg b/board/freescale/mx6sabresd/mx6sabresd_spl.cfg deleted file mode 100644 index 2bf48175ef..0000000000 --- a/board/freescale/mx6sabresd/mx6sabresd_spl.cfg +++ /dev/null @@ -1,58 +0,0 @@ -/* - * Copyright (C) 2011 Freescale Semiconductor, Inc. - * Jason Liu <r64343@freescale.com> - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Refer doc/README.imximage for more details about how-to configure - * and create imximage boot image - * - * The syntax is taken as close as possible with the kwbimage - */ - -/* image version */ -IMAGE_VERSION 2 - -/* - * Boot Device : one of - * spi, sd (the board has no nand neither onenand) - */ -BOOT_FROM sd - -/* - * Device Configuration Data (DCD) - * - * Each entry must have the format: - * Addr-type Address Value - * - * where: - * Addr-type register length (1,2 or 4 bytes) - * Address absolute address of the register - * value value to be stored in the register - */ - -/* set the default clock gate to save power */ -DATA 4 0x020c4068 0x00C03F3F -DATA 4 0x020c406c 0x0030FC03 -DATA 4 0x020c4070 0x0FFFC000 -DATA 4 0x020c4074 0x3FF00000 -DATA 4 0x020c4078 0x00FFF300 -DATA 4 0x020c407c 0x0F0000C3 -DATA 4 0x020c4080 0x000003FF - -/* enable AXI cache for VDOA/VPU/IPU */ -DATA 4 0x020e0010 0xF00000CF -/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ -DATA 4 0x020e0018 0x007F007F -DATA 4 0x020e001c 0x007F007F - -/* - * Setup CCM_CCOSR register as follows: - * - * cko1_en = 1 --> CKO1 enabled - * cko1_div = 111 --> divide by 8 - * cko1_sel = 1011 --> ahb_clk_root - * - * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz - */ -DATA 4 0x020c4060 0x000000fb diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c index e76c343812..8111edf804 100644 --- a/board/freescale/mx6slevk/mx6slevk.c +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -230,16 +230,11 @@ int board_eth_init(bd_t *bis) static int setup_fec(void) { struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; - int ret; /* clear gpr1[14], gpr1[18:17] to select anatop clock */ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0); - ret = enable_fec_anatop_clock(ENET_50MHz); - if (ret) - return ret; - - return 0; + return enable_fec_anatop_clock(ENET_50MHz); } #endif diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index 68d37184a3..7aee074a87 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -25,6 +25,7 @@ #include <netdev.h> #include <power/pmic.h> #include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" DECLARE_GLOBAL_DATA_PTR; @@ -68,6 +69,34 @@ static iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), }; +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc3_pads[] = { + MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD pin */ + MX6_PAD_KEY_COL0__GPIO2_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* RST_B, used for power reset cycle */ + MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + static iomux_v3_cfg_t const usdhc4_pads[] = { MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -119,7 +148,6 @@ static int setup_fec(void) { struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; - int ret; int reg; /* Use 125MHz anatop loopback REF_CLK1 for ENET1 */ @@ -140,11 +168,7 @@ static int setup_fec(void) reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE; writel(reg, &anatop->pll_enet); - ret = enable_fec_anatop_clock(ENET_125MHz); - if (ret) - return ret; - - return 0; + return enable_fec_anatop_clock(ENET_125MHz); } int board_eth_init(bd_t *bis) @@ -170,52 +194,19 @@ static struct i2c_pads_info i2c_pad_info1 = { }, }; -static int pfuze_init(void) +int power_init_board(void) { struct pmic *p; - int ret; unsigned int reg; - ret = power_pfuze100_init(I2C_PMIC); - if (ret) - return ret; - - p = pmic_get("PFUZE100"); - ret = pmic_probe(p); - if (ret) - return ret; - - pmic_reg_read(p, PFUZE100_DEVICEID, ®); - printf("PMIC: PFUZE100 ID=0x%02x\n", reg); - - /* Set SW1AB standby voltage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); - - /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PUZE_100_SW1ABCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PUZE_100_SW1ABCONF, reg); - - /* Set SW1C standby voltage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); - - /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PFUZE100_SW1CCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PFUZE100_SW1CCONF, reg); + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; /* Enable power of VGEN5 3V3, needed for SD3 */ pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); - reg &= ~0x1F; - reg |= 0x1F; + reg &= ~LDO_VOL_MASK; + reg |= (LDOB_3_30V | (1 << LDO_EN)); pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); return 0; @@ -243,7 +234,6 @@ int board_phy_config(struct phy_device *phydev) int board_early_init_f(void) { setup_iomux_uart(); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */ imx_iomux_v3_setup_multiple_pads(peri_3v3_pads, @@ -255,35 +245,98 @@ int board_early_init_f(void) return 0; } -static struct fsl_esdhc_cfg usdhc_cfg[1] = { +static struct fsl_esdhc_cfg usdhc_cfg[3] = { + {USDHC2_BASE_ADDR, 0, 4}, + {USDHC3_BASE_ADDR}, {USDHC4_BASE_ADDR}, }; +#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 10) +#define USDHC3_PWR_GPIO IMX_GPIO_NR(2, 11) +#define USDHC4_CD_GPIO IMX_GPIO_NR(6, 21) + int board_mmc_getcd(struct mmc *mmc) { - return 1; /* Assume boot SD always present */ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC2_BASE_ADDR: + ret = 1; /* Assume uSDHC2 is always present */ + break; + case USDHC3_BASE_ADDR: + ret = !gpio_get_value(USDHC3_CD_GPIO); + break; + case USDHC4_BASE_ADDR: + ret = !gpio_get_value(USDHC4_CD_GPIO); + break; + } + + return ret; } int board_mmc_init(bd_t *bis) { - imx_iomux_v3_setup_multiple_pads(usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); + int i, ret; - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); - return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * mmc0 USDHC2 + * mmc1 USDHC3 + * mmc2 USDHC4 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + imx_iomux_v3_setup_multiple_pads( + usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + break; + case 1: + imx_iomux_v3_setup_multiple_pads( + usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + gpio_direction_input(USDHC3_CD_GPIO); + gpio_direction_output(USDHC3_PWR_GPIO, 1); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + break; + case 2: + imx_iomux_v3_setup_multiple_pads( + usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); + gpio_direction_input(USDHC4_CD_GPIO); + usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + break; + default: + printf("Warning: you configured more USDHC controllers" + "(%d) than supported by the board\n", i + 1); + return -EINVAL; + } + + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + + return 0; } + int board_init(void) { /* Address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; +#ifdef CONFIG_SYS_I2C_MXC + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); +#endif + return 0; } int board_late_init(void) { - pfuze_init(); - return 0; } diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c index 491b576258..1cf0ab78b7 100644 --- a/board/freescale/p1010rdb/p1010rdb.c +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -444,7 +444,7 @@ void fdt_disable_uart1(void *blob) } } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -496,6 +496,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_del_flexcan(blob); fdt_disable_uart1(blob); } + + return 0; } #endif diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c index f5e18515a0..d7dd478dff 100644 --- a/board/freescale/p1022ds/p1022ds.c +++ b/board/freescale/p1022ds/p1022ds.c @@ -332,7 +332,7 @@ static void ft_codec_setup(void *blob, const char *compatible) } } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -356,5 +356,7 @@ void ft_board_setup(void *blob, bd_t *bd) /* Update the WM8776 node's clock frequency property */ ft_codec_setup(blob, "wlf,wm8776"); + + return 0; } #endif diff --git a/board/freescale/p1023rdb/p1023rdb.c b/board/freescale/p1023rdb/p1023rdb.c index d4d277ba6d..56f561a505 100644 --- a/board/freescale/p1023rdb/p1023rdb.c +++ b/board/freescale/p1023rdb/p1023rdb.c @@ -130,7 +130,7 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -147,5 +147,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif fdt_fixup_fman_ethernet(blob); + + return 0; } #endif diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c b/board/freescale/p1_p2_rdb/p1_p2_rdb.c index aba4f534b8..61ed466fa7 100644 --- a/board/freescale/p1_p2_rdb/p1_p2_rdb.c +++ b/board/freescale/p1_p2_rdb/p1_p2_rdb.c @@ -234,7 +234,7 @@ int board_eth_init(bd_t *bis) #if defined(CONFIG_OF_BOARD_SETUP) extern void ft_pci_board_setup(void *blob); -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { const char *soc_usb_compat = "fsl-usb2-dr"; int err, usb1_off, usb2_off; @@ -263,39 +263,41 @@ void ft_board_setup(void *blob, bd_t *bd) int off = fdt_node_offset_by_compatible(blob, -1, soc_elbc_compat); if (off < 0) { - printf("WARNING: could not find compatible node" - " %s: %s.\n", soc_elbc_compat, - fdt_strerror(off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_elbc_compat); + return off; } err = fdt_del_node(blob, off); if (err < 0) { - printf("WARNING: could not remove %s: %s.\n", - soc_elbc_compat, fdt_strerror(err)); + printf("WARNING: could not remove %s\n", + soc_elbc_compat); + return err; } - return; + return 0; } #endif /* Delete USB2 node as it is muxed with eLBC */ usb1_off = fdt_node_offset_by_compatible(blob, -1, soc_usb_compat); if (usb1_off < 0) { - printf("WARNING: could not find compatible node" - " %s: %s.\n", soc_usb_compat, - fdt_strerror(usb1_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb1_off; } usb2_off = fdt_node_offset_by_compatible(blob, usb1_off, soc_usb_compat); if (usb2_off < 0) { - printf("WARNING: could not find compatible node" - " %s: %s.\n", soc_usb_compat, - fdt_strerror(usb2_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb2_off; } err = fdt_del_node(blob, usb2_off); - if (err < 0) - printf("WARNING: could not remove %s: %s.\n", - soc_usb_compat, fdt_strerror(err)); + if (err < 0) { + printf("WARNING: could not remove %s\n", soc_usb_compat); + return err; + } + + return 0; } + #endif diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c index a6756c68f4..3f47cfbb82 100644 --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c @@ -424,7 +424,7 @@ static void fdt_board_fixup_qe_pins(void *blob) #endif #ifdef CONFIG_OF_BOARD_SETUP -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -459,17 +459,17 @@ void ft_board_setup(void *blob, bd_t *bd) int off = fdt_node_offset_by_compatible(blob, -1, soc_elbc_compat); if (off < 0) { - printf("WARNING: could not find compatible node %s: %s.\n", - soc_elbc_compat, - fdt_strerror(off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_elbc_compat); + return off; } err = fdt_del_node(blob, off); if (err < 0) { - printf("WARNING: could not remove %s: %s.\n", - soc_elbc_compat, fdt_strerror(err)); + printf("WARNING: could not remove %s\n", + soc_elbc_compat); + return err; } - return; + return 0; } #endif @@ -477,24 +477,23 @@ void ft_board_setup(void *blob, bd_t *bd) usb1_off = fdt_node_offset_by_compatible(blob, -1, soc_usb_compat); if (usb1_off < 0) { - printf("WARNING: could not find compatible node %s: %s.\n", - soc_usb_compat, - fdt_strerror(usb1_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb1_off; } usb2_off = fdt_node_offset_by_compatible(blob, usb1_off, soc_usb_compat); if (usb2_off < 0) { - printf("WARNING: could not find compatible node %s: %s.\n", - soc_usb_compat, - fdt_strerror(usb2_off)); - return; + printf("WARNING: could not find compatible node %s\n", + soc_usb_compat); + return usb2_off; } err = fdt_del_node(blob, usb2_off); if (err < 0) { - printf("WARNING: could not remove %s: %s.\n", - soc_usb_compat, fdt_strerror(err)); + printf("WARNING: could not remove %s\n", soc_usb_compat); + return err; } + return 0; } #endif diff --git a/board/freescale/p1_twr/p1_twr.c b/board/freescale/p1_twr/p1_twr.c index a0a416ba17..a40bea328b 100644 --- a/board/freescale/p1_twr/p1_twr.c +++ b/board/freescale/p1_twr/p1_twr.c @@ -261,7 +261,7 @@ static void fdt_board_fixup_qe_pins(void *blob) #endif #ifdef CONFIG_OF_BOARD_SETUP -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -283,5 +283,7 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_board_fixup_qe_pins(blob); #endif fdt_fixup_dr_usb(blob, bd); + + return 0; } #endif diff --git a/board/freescale/p2020come/p2020come.c b/board/freescale/p2020come/p2020come.c index f777bb9d67..1db37e3be8 100644 --- a/board/freescale/p2020come/p2020come.c +++ b/board/freescale/p2020come/p2020come.c @@ -250,7 +250,7 @@ int board_eth_init(bd_t *bis) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -269,5 +269,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_HAS_FSL_DR_USB fdt_fixup_dr_usb(blob, bd); #endif + + return 0; } #endif diff --git a/board/freescale/p2020ds/p2020ds.c b/board/freescale/p2020ds/p2020ds.c index b72fcffdd0..5d18e8de75 100644 --- a/board/freescale/p2020ds/p2020ds.c +++ b/board/freescale/p2020ds/p2020ds.c @@ -236,7 +236,7 @@ int board_eth_init(bd_t *bis) #endif #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -257,5 +257,7 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + return 0; } #endif diff --git a/board/freescale/p2041rdb/p2041rdb.c b/board/freescale/p2041rdb/p2041rdb.c index a14b43b5a5..e600bdbc2a 100644 --- a/board/freescale/p2041rdb/p2041rdb.c +++ b/board/freescale/p2041rdb/p2041rdb.c @@ -215,7 +215,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -239,4 +239,6 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_SYS_DPAA_FMAN fdt_fixup_fman_ethernet(blob); #endif + + return 0; } diff --git a/board/freescale/qemu-ppce500/qemu-ppce500.c b/board/freescale/qemu-ppce500/qemu-ppce500.c index 230870d90e..a0fca0d880 100644 --- a/board/freescale/qemu-ppce500/qemu-ppce500.c +++ b/board/freescale/qemu-ppce500/qemu-ppce500.c @@ -235,9 +235,11 @@ int board_eth_init(bd_t *bis) } #if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { FT_FSL_PCI_SETUP; + + return 0; } #endif diff --git a/board/freescale/t1040qds/t1040qds.c b/board/freescale/t1040qds/t1040qds.c index 19af46e48f..13285be42c 100644 --- a/board/freescale/t1040qds/t1040qds.c +++ b/board/freescale/t1040qds/t1040qds.c @@ -233,7 +233,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -259,6 +259,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } void qixis_dump_switch(void) diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c index ddb669fb06..4734f9dd93 100644 --- a/board/freescale/t104xrdb/t104xrdb.c +++ b/board/freescale/t104xrdb/t104xrdb.c @@ -85,7 +85,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -110,6 +110,8 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_SYS_DPAA_FMAN fdt_fixup_fman_ethernet(blob); #endif + + return 0; } #ifdef CONFIG_DEEP_SLEEP diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README new file mode 100755 index 0000000000..83060c10f3 --- /dev/null +++ b/board/freescale/t208xqds/README @@ -0,0 +1,274 @@ +The T2080QDS is a high-performance computing evaluation, development and +test platform supporting the T2080 QorIQ Power Architecture processor. + +T2080 SoC Overview +------------------ +The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power +Architecture processor cores with high-performance datapath acceleration +logic and network and peripheral bus interfaces required for networking, +telecom/datacom, wireless infrastructure, and mil/aerospace applications. + +T2080 includes the following functions and features: + - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz + - 2MB L2 cache and 512KB CoreNet platform cache (CPC) + - Hierarchical interconnect fabric + - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving + - Data Path Acceleration Architecture (DPAA) incorporating acceleration + - 16 SerDes lanes up to 10.3125 GHz + - 8 Ethernet interfaces, supporting combinations of the following: + - Up to four 10 Gbps Ethernet MACs + - Up to eight 1 Gbps Ethernet MACs + - Up to four 2.5 Gbps Ethernet MACs + - High-speed peripheral interfaces + - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) + - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz + - Additional peripheral interfaces + - Two serial ATA (SATA 2.0) controllers + - Two high-speed USB 2.0 controllers with integrated PHY + - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC) + - Enhanced serial peripheral interface (eSPI) + - Four I2C controllers + - Four 2-pin UARTs or two 4-pin UARTs + - Integrated Flash Controller supporting NAND and NOR flash + - Three eight-channel DMA engines + - Support for hardware virtualization and partitioning enforcement + - QorIQ Platform's Trust Architecture 2.0 + +Differences between T2080 and T2081 +----------------------------------- + Feature T2080 T2081 + 1G Ethernet numbers: 8 6 + 10G Ethernet numbers: 4 2 + SerDes lanes: 16 8 + Serial RapidIO,RMan: 2 no + SATA Controller: 2 no + Aurora: yes no + SoC Package: 896-pins 780-pins + + +T2080QDS feature overview +------------------------- +Processor: + - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz +Memory: + - Single memory controller capable of supporting DDR3 and DDR3-LV devices + - Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support +Ethernet interfaces: + - Two 1Gbps RGMII on-board ports + - Four 10Gbps XFI on-board cages + - 1Gbps/2.5Gbps SGMII Riser card + - 10Gbps XAUI Riser card +Accelerator: + - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC +SerDes: + - 16 lanes up to 10.3125GHz + - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI +IFC: + - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA +eSPI: + - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) +USB: + - Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB) +PCIE: + - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) +SATA: + - Two SATA 2.0 ports on-board +SRIO: + - Two Serial RapidIO 2.0 ports up to 5 GHz +eSDHC: + - Supports SD/SDHC/SDXC/eMMC Card +I2C: + - Four I2C controllers. +UART: + - Dual 4-pins UART serial ports +System Logic: + - QIXIS-II FPGA system controll +Debug Features: + - Support Legacy, COP/JTAG, Aurora, Event and EVT +XFI: + - XFI is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to + a on-board SFP+ cages, which to house optical module (fiber cable) or + direct attach cable(copper), the copper cable is used to emulate + 10GBASE-KR scenario. + So, for XFI usage, there are two scenarios, one will use fiber cable, + another will use copper cable. An hwconfig env "fsl_10gkr_copper" is + introduced to indicate a XFI port will use copper cable, and U-boot + will fixup the dtb accordingly. + It's used as: fsl_10gkr_copper:<10g_mac_name> + The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4, they + do not have to be coexist in hwconfig. If a MAC is listed in the env + "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable + will be used by default. + for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4" in + hwconfig, then both four XFI ports will use copper cable. + set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two + XFI ports will use copper cable, the other two XFI ports will use fiber + cable. +1000BASE-KX(1G-KX): + - T2080QDS can support 1G-KX by using SGMII protocol, but serdes lane + runs in 1G-KX mode. By default, the lane runs in SGMII mode, to set a lane + in 1G-KX mode, need to set corresponding bit in SerDes Protocol Configuration + Register 1 (PCCR1), and U-boot fixup the dtb for kernel to do proper + initialization. + Hwconfig "fsl_1gkx" is used to indicate a lane runs in 1G-KX mode, MAC + 1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a + MAC to use 1G-KX mode, set its' corresponding env in "fsl_1gkx", 'fm1_1g1' + stands for MAC 1, 'fm1_1g2' stands for MAC 2, etc. + For ex. set "fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10" in + hwconfig, MAC 1/2/5/6/9/10 will use 1G-KX mode. + +System Memory map +---------------- + +Start Address End Address Description Size +0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB +0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB +0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB +0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB +0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB +0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB +0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB +0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB +0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB +0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB +0xF_0000_0000 0xF_003F_FFFF DCSR 4MB +0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB +0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB +0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB +0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB +0x0_0000_0000 0x0_ffff_ffff DDR 4GB + + +128M NOR Flash memory Map +------------------------- +Start Address End Address Definition Max size +0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB +0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB +0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB +0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB +0xEC000000 0xEC01FFFF RCW (alt bank) 128KB +0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB +0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB +0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB +0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB +0xE8000000 0xE801FFFF RCW (current bank) 128KB + + + +Software configurations and board settings +------------------------------------------ +1. NOR boot: + a. build NOR boot image + $ make T2080QDS_config + $ make + b. program u-boot.bin image to NOR flash + => tftp 1000000 u-boot.bin + => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize + set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot + + Switching between default bank0 and alternate bank4 on NOR flash + To change boot source to vbank4: + by software: run command 'qixis_reset altbank' in u-boot. + by DIP-switch: set SW6[1:4] = '0100' + + To change boot source to vbank0: + by software: run command 'qixis_reset' in u-boot. + by DIP-Switch: set SW6[1:4] = '0000' + +2. NAND Boot: + a. build PBL image for NAND boot + $ make T2080QDS_NAND_config + $ make + b. program u-boot-with-spl-pbl.bin to NAND flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => nand erase 0 $filesize + => nand write 1000000 0 $filesize + set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot + +3. SPI Boot: + a. build PBL image for SPI boot + $ make T2080QDS_SPIFLASH_config + $ make + b. program u-boot-with-spl-pbl.bin to SPI flash + => tftp 1000000 u-boot-with-spl-pbl.bin + => sf probe 0 + => sf erase 0 f0000 + => sf write 1000000 0 $filesize + set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot + +4. SD Boot: + a. build PBL image for SD boot + $ make T2080QDS_SDCARD_config + $ make + b. program u-boot-with-spl-pbl.bin to SD/MMC card + => tftp 1000000 u-boot-with-spl-pbl.bin + => mmc write 1000000 8 0x800 + => tftp 1000000 fsl_fman_ucode_T2080_xx.bin + => mmc write 1000000 0x820 80 + set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot + + +2-stage NAND/SPI/SD boot loader +------------------------------- +PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. +SPL further initializes DDR using SPD and environment variables +and copy u-boot(768 KB) from NAND/SPI/SD device to DDR. +Finally SPL transers control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - No relocation required + +Run time view of SPL framework +------------------------------------------------- +|Area | Address | +------------------------------------------------- +|SecureBoot header | 0xFFFC0000 (32KB) | +------------------------------------------------- +|GD, BD | 0xFFFC8000 (4KB) | +------------------------------------------------- +|ENV | 0xFFFC9000 (8KB) | +------------------------------------------------- +|HEAP | 0xFFFCB000 (50KB) | +------------------------------------------------- +|STACK | 0xFFFD8000 (22KB) | +------------------------------------------------- +|U-boot SPL | 0xFFFD8000 (160KB) | +------------------------------------------------- + +NAND Flash memory Map on T2080QDS +-------------------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB (2 blocks) +0x100000 0x17FFFF u-boot env 512KB (1 block) +0x180000 0x1FFFFF FMAN ucode 512KB (1 block) + + +Micro SD Card memory Map on T2080QDS +---------------------------------------------------- +Block #blocks Definition Size +0x008 2048 u-boot img 1MB +0x800 0016 u-boot env 8KB +0x820 0128 FMAN ucode 64KB + + +SPI Flash memory Map on T2080QDS +---------------------------------------------------- +Start End Definition Size +0x000000 0x0FFFFF u-boot img 1MB +0x100000 0x101FFF u-boot env 8KB +0x110000 0x11FFFF FMAN ucode 64KB + + +How to update the ucode of Freescale FMAN +----------------------------------------- +=> tftp 1000000 fsl_fman_ucode_t2080_xx.bin +=> pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize + + +For more details, please refer to T2080QDS User Guide and access +website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t208xqds/eth_t208xqds.c b/board/freescale/t208xqds/eth_t208xqds.c index 5879198e4d..b82e9e7540 100644 --- a/board/freescale/t208xqds/eth_t208xqds.c +++ b/board/freescale/t208xqds/eth_t208xqds.c @@ -23,6 +23,7 @@ #include <phy.h> #include <asm/fsl_dtsec.h> #include <asm/fsl_serdes.h> +#include <hwconfig.h> #include "../common/qixis.h" #include "../common/fman.h" #include "t208xqds_qixis.h" @@ -46,6 +47,15 @@ #define EMI2 8 #endif +#define PCCR1_SGMIIA_KX_MASK 0x00008000 +#define PCCR1_SGMIIB_KX_MASK 0x00004000 +#define PCCR1_SGMIIC_KX_MASK 0x00002000 +#define PCCR1_SGMIID_KX_MASK 0x00001000 +#define PCCR1_SGMIIE_KX_MASK 0x00000800 +#define PCCR1_SGMIIF_KX_MASK 0x00000400 +#define PCCR1_SGMIIG_KX_MASK 0x00000200 +#define PCCR1_SGMIIH_KX_MASK 0x00000100 + static int mdio_mux[NUM_FM_PORTS]; static const char * const mdio_names[] = { @@ -187,8 +197,18 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, { int phy; char alias[20]; + char lane_mode[2][20] = {"1000BASE-KX", "10GBASE-KR"}; + char buf[32] = "serdes-1,"; struct fixed_link f_link; + int media_type = 0; + int off; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#ifdef CONFIG_T2080QDS + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 srds1_pccr1 = in_be32(&srds_regs->srdspccr1); +#endif u32 srds_s1 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS1_PRTCL; @@ -199,9 +219,54 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, switch (port) { #if defined(CONFIG_T2080QDS) case FM1_DTSEC1: + if (hwconfig_sub("fsl_1gkx", "fm1_1g1")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx1"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio1"); + sprintf(buf, "%s%s%s", buf, "lane-c,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIH_KX_MASK); + break; + } case FM1_DTSEC2: + if (hwconfig_sub("fsl_1gkx", "fm1_1g2")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx2"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio2"); + sprintf(buf, "%s%s%s", buf, "lane-d,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIG_KX_MASK); + break; + } case FM1_DTSEC9: + if (hwconfig_sub("fsl_1gkx", "fm1_1g9")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx9"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio9"); + sprintf(buf, "%s%s%s", buf, "lane-a,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIE_KX_MASK); + break; + } case FM1_DTSEC10: + if (hwconfig_sub("fsl_1gkx", "fm1_1g10")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx10"); + fdt_status_okay_by_alias(fdt, + "1gkx_pcs_mdio10"); + sprintf(buf, "%s%s%s", buf, "lane-b,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIF_KX_MASK); + break; + } if (mdio_mux[port] == EMI1_SLOT2) { sprintf(alias, "phy_sgmii_s2_%x", phy); fdt_set_phy_handle(fdt, compat, addr, alias); @@ -213,7 +278,29 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, } break; case FM1_DTSEC5: + if (hwconfig_sub("fsl_1gkx", "fm1_1g5")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx5"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio5"); + sprintf(buf, "%s%s%s", buf, "lane-g,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIIC_KX_MASK); + break; + } case FM1_DTSEC6: + if (hwconfig_sub("fsl_1gkx", "fm1_1g6")) { + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_1gkx6"); + fdt_status_okay_by_alias(fdt, "1gkx_pcs_mdio6"); + sprintf(buf, "%s%s%s", buf, "lane-h,", + (char *)lane_mode[0]); + out_be32(&srds_regs->srdspccr1, srds1_pccr1 | + PCCR1_SGMIID_KX_MASK); + break; + } if (mdio_mux[port] == EMI1_SLOT1) { sprintf(alias, "phy_sgmii_s1_%x", phy); fdt_set_phy_handle(fdt, compat, addr, alias); @@ -257,6 +344,12 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, default: break; } + if (media_type) { + /* set property for 1000BASE-KX in dtb */ + off = fdt_node_offset_by_compat_reg(fdt, + "fsl,fman-memac-mdio", addr + 0x1000); + fdt_setprop_string(fdt, off, "lane-instance", buf); + } } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { switch (srds_s1) { @@ -265,15 +358,77 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, case 0x6c: case 0x6d: case 0x71: - f_link.phy_id = port; - f_link.duplex = 1; - f_link.link_speed = 10000; - f_link.pause = 0; - f_link.asym_pause = 0; - /* no PHY for XFI */ - fdt_delprop(fdt, offset, "phy-handle"); - fdt_setprop(fdt, offset, "fixed-link", &f_link, - sizeof(f_link)); + /* + * if the 10G is XFI, check hwconfig to see what is the + * media type, there are two types, fiber or copper, + * fix the dtb accordingly. + */ + switch (port) { + case FM1_10GEC1: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g1")) { + /* it's MAC9 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi9"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio9"); + sprintf(buf, "%s%s%s", buf, "lane-a,", + (char *)lane_mode[1]); + } + break; + case FM1_10GEC2: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g2")) { + /* it's MAC10 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi10"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio10"); + sprintf(buf, "%s%s%s", buf, "lane-b,", + (char *)lane_mode[1]); + } + break; + case FM1_10GEC3: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g3")) { + /* it's MAC1 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi1"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio1"); + sprintf(buf, "%s%s%s", buf, "lane-c,", + (char *)lane_mode[1]); + } + break; + case FM1_10GEC4: + if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g4")) { + /* it's MAC2 */ + media_type = 1; + fdt_set_phy_handle(fdt, compat, addr, + "phy_xfi2"); + fdt_status_okay_by_alias(fdt, "xfi_pcs_mdio2"); + sprintf(buf, "%s%s%s", buf, "lane-d,", + (char *)lane_mode[1]); + } + break; + default: + return; + } + + if (!media_type) { + /* fixed-link is used for XFI fiber cable */ + f_link.phy_id = port; + f_link.duplex = 1; + f_link.link_speed = 10000; + f_link.pause = 0; + f_link.asym_pause = 0; + fdt_delprop(fdt, offset, "phy-handle"); + fdt_setprop(fdt, offset, "fixed-link", &f_link, + sizeof(f_link)); + } else { + /* set property for copper cable */ + off = fdt_node_offset_by_compat_reg(fdt, + "fsl,fman-memac-mdio", addr + 0x1000); + fdt_setprop_string(fdt, off, + "lane-instance", buf); + } break; default: break; diff --git a/board/freescale/t208xqds/t208xqds.c b/board/freescale/t208xqds/t208xqds.c index fc6d256111..5c470c3a49 100644 --- a/board/freescale/t208xqds/t208xqds.c +++ b/board/freescale/t208xqds/t208xqds.c @@ -437,7 +437,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -460,4 +460,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c index be99fb806d..341453bc74 100644 --- a/board/freescale/t208xrdb/t208xrdb.c +++ b/board/freescale/t208xrdb/t208xrdb.c @@ -103,7 +103,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -126,4 +126,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } diff --git a/board/freescale/t4qds/t4240emu.c b/board/freescale/t4qds/t4240emu.c index 479e124a39..54410943f2 100644 --- a/board/freescale/t4qds/t4240emu.c +++ b/board/freescale/t4qds/t4240emu.c @@ -69,7 +69,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -83,4 +83,6 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_liodn(blob); fdt_fixup_dr_usb(blob, bd); + + return 0; } diff --git a/board/freescale/t4qds/t4240qds.c b/board/freescale/t4qds/t4240qds.c index 6205fea35e..4f2cccd709 100644 --- a/board/freescale/t4qds/t4240qds.c +++ b/board/freescale/t4qds/t4240qds.c @@ -683,7 +683,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -706,6 +706,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } /* diff --git a/board/freescale/t4rdb/t4240rdb.c b/board/freescale/t4rdb/t4240rdb.c index 2ff77b8487..fac442bfc8 100644 --- a/board/freescale/t4rdb/t4240rdb.c +++ b/board/freescale/t4rdb/t4240rdb.c @@ -88,7 +88,7 @@ int misc_init_r(void) return 0; } -void ft_board_setup(void *blob, bd_t *bd) +int ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; phys_size_t size; @@ -111,6 +111,8 @@ void ft_board_setup(void *blob, bd_t *bd) fdt_fixup_fman_ethernet(blob); fdt_fixup_board_enet(blob); #endif + + return 0; } /* |