diff options
| -rw-r--r-- | doc/device-tree-bindings/net/phy/atheros.txt | 35 | ||||
| -rw-r--r-- | drivers/net/phy/atheros.c | 350 | ||||
| -rw-r--r-- | include/dt-bindings/net/qca-ar803x.h | 13 |
3 files changed, 345 insertions, 53 deletions
diff --git a/doc/device-tree-bindings/net/phy/atheros.txt b/doc/device-tree-bindings/net/phy/atheros.txt new file mode 100644 index 0000000000..97e97b8c13 --- /dev/null +++ b/doc/device-tree-bindings/net/phy/atheros.txt @@ -0,0 +1,35 @@ +* Qualcomm Atheros PHY Device Tree binding + +Required properties: +- reg: PHY address + +Optional properties: +- qca,clk-out-frequency: Clock frequency of the CLK_25M pin in Hz. + Either 25000000, 50000000, 62500000 or 125000000. +- qca,clk-out-strength: Clock output buffer driver strength. + Supported values are defined in dt-bindings/net/qca-ar803x.h +- qca,keep-pll-enabled: Keep the PLL running if no link is present. + Don't go into hibernation mode. + Only supported on the AR8031/AR8033. +- vddio-supply: RGMII I/O voltage regulator + Only supported on the AR8031/AR8033. + +Optional subnodes: +- vddio-regulator: Initial data for the VDDIO regulator, as covered + doc/device-tree-bindings/regulator/regulator.txt + +Example: + #include <dt-bindings/net/qca-ar803x.h> + + ethernet-phy@0 { + reg = <0>; + qca-clk-out-frequency = <125000000>; + qca,keep-pll-enabled; + + vddio-supply = <&vddio>; + + vddio: vddio-regulator { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; diff --git a/drivers/net/phy/atheros.c b/drivers/net/phy/atheros.c index 3783d155e7..47ff9f8d44 100644 --- a/drivers/net/phy/atheros.c +++ b/drivers/net/phy/atheros.c @@ -4,85 +4,329 @@ * * Copyright 2011, 2013 Freescale Semiconductor, Inc. * author Andy Fleming + * Copyright (c) 2019 Michael Walle <michael@walle.cc> */ #include <common.h> #include <phy.h> +#include <dm/device_compat.h> +#include <linux/bitfield.h> +#include <dt-bindings/net/qca-ar803x.h> #define AR803x_PHY_DEBUG_ADDR_REG 0x1d #define AR803x_PHY_DEBUG_DATA_REG 0x1e +/* Debug registers */ +#define AR803x_DEBUG_REG_0 0x0 +#define AR803x_RGMII_RX_CLK_DLY BIT(15) + #define AR803x_DEBUG_REG_5 0x5 -#define AR803x_RGMII_TX_CLK_DLY 0x100 +#define AR803x_RGMII_TX_CLK_DLY BIT(8) -#define AR803x_DEBUG_REG_0 0x0 -#define AR803x_RGMII_RX_CLK_DLY 0x8000 +#define AR803x_DEBUG_REG_1F 0x1f +#define AR803x_PLL_ON BIT(2) +#define AR803x_RGMII_1V8 BIT(3) + +/* CLK_25M register is at MMD 7, address 0x8016 */ +#define AR803x_CLK_25M_SEL_REG 0x8016 + +#define AR803x_CLK_25M_MASK GENMASK(4, 2) +#define AR803x_CLK_25M_25MHZ_XTAL 0 +#define AR803x_CLK_25M_25MHZ_DSP 1 +#define AR803x_CLK_25M_50MHZ_PLL 2 +#define AR803x_CLK_25M_50MHZ_DSP 3 +#define AR803x_CLK_25M_62_5MHZ_PLL 4 +#define AR803x_CLK_25M_62_5MHZ_DSP 5 +#define AR803x_CLK_25M_125MHZ_PLL 6 +#define AR803x_CLK_25M_125MHZ_DSP 7 +#define AR8035_CLK_25M_MASK GENMASK(4, 3) + +#define AR803x_CLK_25M_DR_MASK GENMASK(8, 7) +#define AR803x_CLK_25M_DR_FULL 0 +#define AR803x_CLK_25M_DR_HALF 1 +#define AR803x_CLK_25M_DR_QUARTER 2 + +#define AR8021_PHY_ID 0x004dd040 +#define AR8031_PHY_ID 0x004dd074 +#define AR8035_PHY_ID 0x004dd072 + +struct ar803x_priv { + int flags; +#define AR803x_FLAG_KEEP_PLL_ENABLED BIT(0) /* don't turn off internal PLL */ +#define AR803x_FLAG_RGMII_1V8 BIT(1) /* use 1.8V RGMII I/O voltage */ + u16 clk_25m_reg; + u16 clk_25m_mask; +}; + +static int ar803x_debug_reg_read(struct phy_device *phydev, u16 reg) +{ + int ret; + + ret = phy_write(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_ADDR_REG, + reg); + if (ret < 0) + return ret; + + return phy_read(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_DATA_REG); +} + +static int ar803x_debug_reg_mask(struct phy_device *phydev, u16 reg, + u16 clear, u16 set) +{ + int val; + + val = ar803x_debug_reg_read(phydev, reg); + if (val < 0) + return val; + + val &= 0xffff; + val &= ~clear; + val |= set; + + return phy_write(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_DATA_REG, + val); +} + +static int ar803x_enable_rx_delay(struct phy_device *phydev, bool on) +{ + u16 clear = 0, set = 0; + + if (on) + set = AR803x_RGMII_RX_CLK_DLY; + else + clear = AR803x_RGMII_RX_CLK_DLY; + + return ar803x_debug_reg_mask(phydev, AR803x_DEBUG_REG_0, clear, set); +} + +static int ar803x_enable_tx_delay(struct phy_device *phydev, bool on) +{ + u16 clear = 0, set = 0; + + if (on) + set = AR803x_RGMII_TX_CLK_DLY; + else + clear = AR803x_RGMII_TX_CLK_DLY; + + return ar803x_debug_reg_mask(phydev, AR803x_DEBUG_REG_5, clear, set); +} static int ar8021_config(struct phy_device *phydev) { - phy_write(phydev, MDIO_DEVAD_NONE, 0x00, 0x1200); - phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); - phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47); + phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, + BMCR_ANENABLE | BMCR_ANRESTART); + + ar803x_enable_tx_delay(phydev, true); phydev->supported = phydev->drv->features; return 0; } -static int ar8031_config(struct phy_device *phydev) +static int ar803x_delay_config(struct phy_device *phydev) { + int ret; + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID || - phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { - phy_write(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_ADDR_REG, - AR803x_DEBUG_REG_5); - phy_write(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_DATA_REG, - AR803x_RGMII_TX_CLK_DLY); - } + phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) + ret = ar803x_enable_tx_delay(phydev, true); + else + ret = ar803x_enable_tx_delay(phydev, false); if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID || - phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { - phy_write(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_ADDR_REG, - AR803x_DEBUG_REG_0); - phy_write(phydev, MDIO_DEVAD_NONE, AR803x_PHY_DEBUG_DATA_REG, - AR803x_RGMII_RX_CLK_DLY); - } + phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) + ret = ar803x_enable_rx_delay(phydev, true); + else + ret = ar803x_enable_rx_delay(phydev, false); - phydev->supported = phydev->drv->features; + return ret; +} - genphy_config_aneg(phydev); - genphy_restart_aneg(phydev); +static int ar803x_regs_config(struct phy_device *phydev) +{ + struct ar803x_priv *priv = phydev->priv; + u16 set = 0, clear = 0; + int val; + int ret; + + /* no configuration available */ + if (!priv) + return 0; + + /* + * Only supported on the AR8031, AR8035 has strappings for the PLL mode + * as well as the RGMII voltage. + */ + if (phydev->drv->uid == AR8031_PHY_ID) { + if (priv->flags & AR803x_FLAG_KEEP_PLL_ENABLED) + set |= AR803x_PLL_ON; + else + clear |= AR803x_PLL_ON; + + if (priv->flags & AR803x_FLAG_RGMII_1V8) + set |= AR803x_RGMII_1V8; + else + clear |= AR803x_RGMII_1V8; + + ret = ar803x_debug_reg_mask(phydev, AR803x_DEBUG_REG_1F, clear, + set); + if (ret < 0) + return ret; + } + + /* save the write access if the mask is empty */ + if (priv->clk_25m_mask) { + val = phy_read_mmd(phydev, MDIO_MMD_AN, AR803x_CLK_25M_SEL_REG); + if (val < 0) + return val; + val &= ~priv->clk_25m_mask; + val |= priv->clk_25m_reg; + ret = phy_write_mmd(phydev, MDIO_MMD_AN, + AR803x_CLK_25M_SEL_REG, val); + if (ret < 0) + return ret; + } return 0; } -static int ar8035_config(struct phy_device *phydev) +static int ar803x_of_init(struct phy_device *phydev) { - int regval; - - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x0007); - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); - regval = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, (regval|0x0018)); - - phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); - regval = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); - phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, (regval|0x0100)); - - if ((phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) { - /* select debug reg 5 */ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1D, 0x5); - /* enable tx delay */ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1E, 0x0100); +#if defined(CONFIG_DM_ETH) + struct ar803x_priv *priv; + ofnode node, vddio_reg_node; + u32 strength, freq, min_uV, max_uV; + int sel; + + node = phy_get_ofnode(phydev); + if (!ofnode_valid(node)) + return -EINVAL; + + priv = malloc(sizeof(*priv)); + if (!priv) + return -ENOMEM; + memset(priv, 0, sizeof(*priv)); + + phydev->priv = priv; + + debug("%s: found PHY node: %s\n", __func__, ofnode_get_name(node)); + + if (ofnode_read_bool(node, "qca,keep-pll-enabled")) + priv->flags |= AR803x_FLAG_KEEP_PLL_ENABLED; + + /* + * We can't use the regulator framework because the regulator is + * a subnode of the PHY. So just read the two properties we are + * interested in. + */ + vddio_reg_node = ofnode_find_subnode(node, "vddio-regulator"); + if (ofnode_valid(vddio_reg_node)) { + min_uV = ofnode_read_u32_default(vddio_reg_node, + "regulator-min-microvolt", 0); + max_uV = ofnode_read_u32_default(vddio_reg_node, + "regulator-max-microvolt", 0); + + if (min_uV != max_uV) { + free(priv); + return -EINVAL; + } + + switch (min_uV) { + case 1500000: + break; + case 1800000: + priv->flags |= AR803x_FLAG_RGMII_1V8; + break; + default: + free(priv); + return -EINVAL; + } + } + + /* + * Get the CLK_25M frequency from the device tree. Only XTAL and PLL + * sources are supported right now. There is also the possibilty to use + * the DSP as frequency reference, this is used for synchronous + * ethernet. + */ + if (!ofnode_read_u32(node, "qca,clk-out-frequency", &freq)) { + switch (freq) { + case 25000000: + sel = AR803x_CLK_25M_25MHZ_XTAL; + break; + case 50000000: + sel = AR803x_CLK_25M_50MHZ_PLL; + break; + case 62500000: + sel = AR803x_CLK_25M_62_5MHZ_PLL; + break; + case 125000000: + sel = AR803x_CLK_25M_125MHZ_PLL; + break; + default: + dev_err(phydev->dev, + "invalid qca,clk-out-frequency\n"); + free(priv); + return -EINVAL; + } + + priv->clk_25m_mask |= AR803x_CLK_25M_MASK; + priv->clk_25m_reg |= FIELD_PREP(AR803x_CLK_25M_MASK, sel); + /* + * Fixup for the AR8035 which only has two bits. The two + * remaining bits map to the same frequencies. + */ + if (phydev->drv->uid == AR8035_PHY_ID) { + u16 clear = AR803x_CLK_25M_MASK & AR8035_CLK_25M_MASK; + + priv->clk_25m_mask &= ~clear; + priv->clk_25m_reg &= ~clear; + } } - if ((phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID)) { - /* select debug reg 0 */ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1D, 0x0); - /* enable rx delay */ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1E, 0x8000); + if (phydev->drv->uid == AR8031_PHY_ID && + !ofnode_read_u32(node, "qca,clk-out-strength", &strength)) { + switch (strength) { + case AR803X_STRENGTH_FULL: + sel = AR803x_CLK_25M_DR_FULL; + break; + case AR803X_STRENGTH_HALF: + sel = AR803x_CLK_25M_DR_HALF; + break; + case AR803X_STRENGTH_QUARTER: + sel = AR803x_CLK_25M_DR_QUARTER; + break; + default: + dev_err(phydev->dev, + "invalid qca,clk-out-strength\n"); + free(priv); + return -EINVAL; + } + priv->clk_25m_mask |= AR803x_CLK_25M_DR_MASK; + priv->clk_25m_reg |= FIELD_PREP(AR803x_CLK_25M_DR_MASK, sel); } + debug("%s: flags=%x clk_25m_reg=%04x clk_25m_mask=%04x\n", __func__, + priv->flags, priv->clk_25m_reg, priv->clk_25m_mask); +#endif + + return 0; +} + +static int ar803x_config(struct phy_device *phydev) +{ + int ret; + + ret = ar803x_of_init(phydev); + if (ret < 0) + return ret; + + ret = ar803x_delay_config(phydev); + if (ret < 0) + return ret; + + ret = ar803x_regs_config(phydev); + if (ret < 0) + return ret; + phydev->supported = phydev->drv->features; genphy_config_aneg(phydev); @@ -93,8 +337,8 @@ static int ar8035_config(struct phy_device *phydev) static struct phy_driver AR8021_driver = { .name = "AR8021", - .uid = 0x4dd040, - .mask = 0x4ffff0, + .uid = AR8021_PHY_ID, + .mask = 0xfffffff0, .features = PHY_GBIT_FEATURES, .config = ar8021_config, .startup = genphy_startup, @@ -103,20 +347,20 @@ static struct phy_driver AR8021_driver = { static struct phy_driver AR8031_driver = { .name = "AR8031/AR8033", - .uid = 0x4dd074, + .uid = AR8031_PHY_ID, .mask = 0xffffffef, .features = PHY_GBIT_FEATURES, - .config = ar8031_config, + .config = ar803x_config, .startup = genphy_startup, .shutdown = genphy_shutdown, }; static struct phy_driver AR8035_driver = { .name = "AR8035", - .uid = 0x4dd072, + .uid = AR8035_PHY_ID, .mask = 0xffffffef, .features = PHY_GBIT_FEATURES, - .config = ar8035_config, + .config = ar803x_config, .startup = genphy_startup, .shutdown = genphy_shutdown, }; diff --git a/include/dt-bindings/net/qca-ar803x.h b/include/dt-bindings/net/qca-ar803x.h new file mode 100644 index 0000000000..9c046c7242 --- /dev/null +++ b/include/dt-bindings/net/qca-ar803x.h @@ -0,0 +1,13 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Device Tree constants for the Qualcomm Atheros AR803x PHYs + */ + +#ifndef _DT_BINDINGS_QCA_AR803X_H +#define _DT_BINDINGS_QCA_AR803X_H + +#define AR803X_STRENGTH_FULL 0 +#define AR803X_STRENGTH_HALF 1 +#define AR803X_STRENGTH_QUARTER 2 + +#endif |