diff options
81 files changed, 211 insertions, 701 deletions
@@ -2213,22 +2213,9 @@ The following options need to be configured: - approved multibus support - better i2c mux support - ** Please consider updating your I2C driver now. ** + ** CONFIG_HARD_I2C is now being removed ** - These enable legacy I2C serial bus commands. Defining - CONFIG_HARD_I2C will include the appropriate I2C driver - for the selected CPU. - - This will allow you to use i2c commands at the u-boot - command line (as long as you set CONFIG_CMD_I2C in - CONFIG_COMMANDS) and communicate with i2c based realtime - clock chips. See common/cmd_i2c.c for a description of the - command line interface. - - CONFIG_HARD_I2C selects a hardware I2C controller. - - There are several other quantities that must also be - defined when you define CONFIG_HARD_I2C. +----under removal: In both cases you will need to define CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you wish your i2c bus diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h index 6ebc759f4b..113e1c73f3 100644 --- a/arch/arm/include/asm/arch-armada100/config.h +++ b/arch/arm/include/asm/arch-armada100/config.h @@ -24,17 +24,5 @@ #define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE #define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register represents UART Unit Enable */ -/* - * I2C definition - */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MV 1 -#define CONFIG_MV_I2C_NUM 2 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000} -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 0 -#define CONFIG_SYS_I2C_SLAVE 0xfe -#endif #endif /* _ARMD1_CONFIG_H */ diff --git a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c index 31418a1f96..9205c22e0b 100644 --- a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c +++ b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c @@ -156,17 +156,7 @@ int board_init(void) int board_late_init(void) { - u8 mac[6]; - - /* Read Mac Address and set*/ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); - - /* Read MAC address */ - i2c_read(0x50, 0x0, 0, mac, 6); - - if (is_valid_ethaddr(mac)) - eth_setenv_enetaddr("ethaddr", mac); + printf("Cannot use I2C to get MAC address\n"); return 0; } diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c index 7b862355c8..2f55191caf 100644 --- a/board/cm5200/cm5200.c +++ b/board/cm5200/cm5200.c @@ -161,14 +161,7 @@ int dram_init(void) */ static void read_hw_id(hw_id_t hw_id) { - int i; - for (i = 0; i < HW_ID_ELEM_COUNT; ++i) - if (i2c_read(CONFIG_SYS_I2C_EEPROM, - hw_id_format[i].offset, - 2, - (uchar *)&hw_id[i][0], - hw_id_format[i].length) != 0) - printf("ERROR: can't read HW ID from EEPROM\n"); + printf("ERROR: can't read HW ID from EEPROM\n"); } @@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf) strcat(buf, tmp); } - +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) /* * Compose string with hostname. * buf is assumed to have enough space, and be null-terminated. @@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf) *p = tolower(*p); } - +#endif #ifdef CONFIG_OF_BOARD_SETUP /* @@ -270,15 +263,6 @@ int checkboard(void) hw_id_t hw_id_tmp; char module_name_tmp[MODULE_NAME_MAXLEN] = ""; - /* - * We need I2C to access HW ID data from EEPROM, so we call i2c_init() - * here despite the fact that it will be called again later on. We - * also use a little trick to silence I2C-related output. - */ - gd->flags |= GD_FLG_SILENT; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - gd->flags &= ~GD_FLG_SILENT; - read_hw_id(hw_id_tmp); identify_module(hw_id_tmp); /* this sets gd->board_type */ compose_module_name(hw_id_tmp, module_name_tmp); @@ -334,16 +318,16 @@ int misc_init_r(void) " device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET); } + hostname[0] = 0x00; + /* set the hostname appropriate to the module we're running on */ + compose_hostname(hw_id, hostname); + setenv("hostname", hostname); + #endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */ if (!getenv("ethaddr")) printf(LOG_PREFIX "MAC address not set, networking is not " "operational\n"); - /* set the hostname appropriate to the module we're running on */ - hostname[0] = 0x00; - compose_hostname(hw_id, hostname); - setenv("hostname", hostname); - return 0; } #endif /* CONFIG_MISC_INIT_R */ diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c index 9c40ad7b2a..60097dc8c7 100644 --- a/board/cm5200/cmd_cm5200.c +++ b/board/cm5200/cmd_cm5200.c @@ -13,34 +13,6 @@ #ifdef CONFIG_CMD_BSP -static int do_i2c_test(char * const argv[]) -{ - unsigned char temp, temp1; - - printf("Starting I2C Test\n" - "Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n" - "Please press any key to start\n\n"); - getc(); - - temp = 0xf0; /* set io 0-4 as output */ - i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1); - - printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n" - "Press any key to stop\n\n"); - - while (!tstc()) { - i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1); - temp1 = (temp >> 4) & 0x03; - temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */ - temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */ - temp = temp1; - i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1); - } - getc(); - - return 0; -} - static int do_usb_test(char * const argv[]) { int i; @@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) switch (argc) { case 2: - if (strncmp(argv[1], "i2c", 3) == 0) - rcode = do_i2c_test(argv); - else if (strncmp(argv[1], "led", 3) == 0) + if (strncmp(argv[1], "led", 3) == 0) rcode = do_led_test(argv); else if (strncmp(argv[1], "usb", 3) == 0) rcode = do_usb_test(argv); diff --git a/board/davedenx/aria/aria.c b/board/davedenx/aria/aria.c index e3441cad4e..e389819e9d 100644 --- a/board/davedenx/aria/aria.c +++ b/board/davedenx/aria/aria.c @@ -29,9 +29,6 @@ int misc_init_r(void) { u32 tmp; - /* we use I2C-2 for on-board eeprom */ - i2c_set_bus_num(2); - tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE); printf("FPGA: %u-%u.%u.%u\n", (tmp & 0xFF000000) >> 24, diff --git a/board/esd/mecp5123/mecp5123.c b/board/esd/mecp5123/mecp5123.c index 66dc407bae..78a6b66110 100644 --- a/board/esd/mecp5123/mecp5123.c +++ b/board/esd/mecp5123/mecp5123.c @@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR; int eeprom_write_enable(unsigned dev_addr, int state) { - volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - - if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR) - return -1; - - if (state == 0) - setbits_be32(&im->gpio.gpdat, 0x00100000); - else - clrbits_be32(&im->gpio.gpdat, 0x00100000); - - return 0; + return -ENOSYS; } int board_early_init_f(void) diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c index f87579f193..d729056fd0 100644 --- a/board/freescale/mpc5121ads/mpc5121ads.c +++ b/board/freescale/mpc5121ads/mpc5121ads.c @@ -174,27 +174,6 @@ int dram_init(void) int misc_init_r(void) { - u8 tmp_val; - - /* Using this for DIU init before the driver in linux takes over - * Enable the TFP410 Encoder (I2C address 0x38) - */ - - i2c_set_bus_num(2); - tmp_val = 0xBF; - i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - - tmp_val = 0x10; - i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - return 0; } diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c index 348613736d..cd79e804a0 100644 --- a/board/ifm/ac14xx/ac14xx.c +++ b/board/ifm/ac14xx/ac14xx.c @@ -17,7 +17,6 @@ #include <i2c.h> #endif -static int eeprom_diag; static int mac_diag; static int gpio_diag; @@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout { #define HW_COMP_MAINCPU 2 static struct eeprom_layout eeprom_content; -static int eeprom_was_read; /* has_been_read */ static int eeprom_is_valid; static int eeprom_version; @@ -153,53 +151,7 @@ static int eeprom_version; static int read_eeprom(void) { - int eeprom_datalen; - int ret; - - if (eeprom_was_read) - return 0; - - eeprom_is_valid = 0; - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, - CONFIG_SYS_I2C_EEPROM_ADDR_LEN, - (uchar *)&eeprom_content, sizeof(eeprom_content)); - if (eeprom_diag) { - printf("DIAG: %s() read rc[%d], size[%d]\n", - __func__, ret, sizeof(eeprom_content)); - } - - if (ret != 0) - return -1; - - eeprom_was_read = 1; - - /* - * check validity of EEPROM content - * (check version, length, optionally checksum) - */ - eeprom_is_valid = 1; - eeprom_datalen = get_eeprom_field_int(eeprom_content.len); - eeprom_version = get_eeprom_field_int(eeprom_content.version); - - if (eeprom_diag) { - printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n", - __func__, eeprom_content.magic[0], - eeprom_content.magic[1], eeprom_content.magic[2], - eeprom_datalen, eeprom_version, eeprom_content.type); - } - if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0) - eeprom_is_valid = 0; - if (eeprom_datalen < sizeof(struct eeprom_layout) - 5) - eeprom_is_valid = 0; - if ((eeprom_version != 1) && (eeprom_version != 2)) - eeprom_is_valid = 0; - if (eeprom_content.type != HW_COMP_MAINCPU) - eeprom_is_valid = 0; - - if (eeprom_diag) - printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid); - - return ret; + return -ENOSYS; } int mac_read_from_eeprom(void) @@ -324,9 +276,6 @@ int misc_init_r(void) char *s; int want_recovery; - /* we use bus I2C-0 for the on-board eeprom */ - i2c_set_bus_num(0); - /* setup GPIO directions and initial values */ gpio_configure(); diff --git a/board/renesas/r0p7734/r0p7734.c b/board/renesas/r0p7734/r0p7734.c index 360e0a1a6f..d0b4537513 100644 --- a/board/renesas/r0p7734/r0p7734.c +++ b/board/renesas/r0p7734/r0p7734.c @@ -44,17 +44,7 @@ int board_init(void) int board_late_init(void) { - u8 mac[6]; - - /* Read Mac Address and set*/ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); - - /* Read MAC address */ - i2c_read(0x50, 0x10, 0, mac, 6); - - if (is_valid_ethaddr(mac)) - eth_setenv_enetaddr("ethaddr", mac); + printf("Cannot get MAC address from I2C\n"); return 0; } diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c index 92db093dbf..c48ab11fc4 100644 --- a/board/tqc/tqm5200/tqm5200.c +++ b/board/tqc/tqm5200/tqm5200.c @@ -486,20 +486,14 @@ int board_early_init_f (void) static int tfp410_read_reg(int reg, uchar *buf) { - if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) { - puts ("Error reading the chip.\n"); - return 1; - } - return 0; + puts("Error reading the chip.\n"); + return -ENOSYS; } static int tfp410_write_reg(int reg, uchar buf) { - if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) { - puts ("Error writing the chip.\n"); - return 1; - } - return 0; + puts("Error writing the chip.\n"); + return -ENOSYS; } typedef struct _tfp410_config { @@ -525,12 +519,9 @@ static int charon_last_stage_init(void) { volatile struct mpc5xxx_lpb *lpb = (struct mpc5xxx_lpb *) MPC5XXX_LPB; - int oldbus = i2c_get_bus_num(); uchar buf; int i = 0; - i2c_set_bus_num(CONFIG_SYS_TFP410_BUS); - /* check version */ if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0) return -1; @@ -551,7 +542,6 @@ static int charon_last_stage_init(void) i++; } printf("TFP410 initialized.\n"); - i2c_set_bus_num(oldbus); /* set deadcycle for cs3 to 0 */ setbits_be32(&lpb->cs_deadcycle, 0xffffcfff); diff --git a/configs/MiniFAP_defconfig b/configs/MiniFAP_defconfig index 7d719f81f5..02ca577e28 100644 --- a/configs/MiniFAP_defconfig +++ b/configs/MiniFAP_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/O2D300_defconfig b/configs/O2D300_defconfig index 38101f05df..c0e9541b87 100644 --- a/configs/O2D300_defconfig +++ b/configs/O2D300_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2DNT2_RAMBOOT_defconfig b/configs/O2DNT2_RAMBOOT_defconfig index 83006e5582..8cff44cf36 100644 --- a/configs/O2DNT2_RAMBOOT_defconfig +++ b/configs/O2DNT2_RAMBOOT_defconfig @@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2DNT2_defconfig b/configs/O2DNT2_defconfig index 4202d85203..f29abb83bc 100644 --- a/configs/O2DNT2_defconfig +++ b/configs/O2DNT2_defconfig @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2D_defconfig b/configs/O2D_defconfig index b84a1c8839..534cfe12e2 100644 --- a/configs/O2D_defconfig +++ b/configs/O2D_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2I_defconfig b/configs/O2I_defconfig index efcc769ff4..acf42abe29 100644 --- a/configs/O2I_defconfig +++ b/configs/O2I_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M110_defconfig b/configs/O2MNT_O2M110_defconfig index abdc53df21..de647c76b9 100644 --- a/configs/O2MNT_O2M110_defconfig +++ b/configs/O2MNT_O2M110_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M112_defconfig b/configs/O2MNT_O2M112_defconfig index 06089fe3cf..b243e9cc0e 100644 --- a/configs/O2MNT_O2M112_defconfig +++ b/configs/O2MNT_O2M112_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M113_defconfig b/configs/O2MNT_O2M113_defconfig index 1ea3f3a09b..1584058289 100644 --- a/configs/O2MNT_O2M113_defconfig +++ b/configs/O2MNT_O2M113_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_defconfig b/configs/O2MNT_defconfig index 0209085605..20bd31466e 100644 --- a/configs/O2MNT_defconfig +++ b/configs/O2MNT_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O3DNT_defconfig b/configs/O3DNT_defconfig index 5ce4140859..ea769e7edc 100644 --- a/configs/O3DNT_defconfig +++ b/configs/O3DNT_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/TQM5200S_HIGHBOOT_defconfig b/configs/TQM5200S_HIGHBOOT_defconfig index d0cd50a63c..d07596add0 100644 --- a/configs/TQM5200S_HIGHBOOT_defconfig +++ b/configs/TQM5200S_HIGHBOOT_defconfig @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200S_defconfig b/configs/TQM5200S_defconfig index 5324a9a11c..af3225554b 100644 --- a/configs/TQM5200S_defconfig +++ b/configs/TQM5200S_defconfig @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_B_HIGHBOOT_defconfig b/configs/TQM5200_B_HIGHBOOT_defconfig index 2f933e6cab..37d6767f28 100644 --- a/configs/TQM5200_B_HIGHBOOT_defconfig +++ b/configs/TQM5200_B_HIGHBOOT_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_B_defconfig b/configs/TQM5200_B_defconfig index f204484f59..5e0cf9ea47 100644 --- a/configs/TQM5200_B_defconfig +++ b/configs/TQM5200_B_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_STK100_defconfig b/configs/TQM5200_STK100_defconfig index db9bb8a30d..7b4b030d74 100644 --- a/configs/TQM5200_STK100_defconfig +++ b/configs/TQM5200_STK100_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_defconfig b/configs/TQM5200_defconfig index eec60f1be4..4792639653 100644 --- a/configs/TQM5200_defconfig +++ b/configs/TQM5200_defconfig @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -18,7 +17,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/a4m072_defconfig b/configs/a4m072_defconfig index ce5edcbf01..0054d4cddb 100644 --- a/configs/a4m072_defconfig +++ b/configs/a4m072_defconfig @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="asdfg" -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/ac14xx_defconfig b/configs/ac14xx_defconfig index e3b7793e04..930ec8acf2 100644 --- a/configs/ac14xx_defconfig +++ b/configs/ac14xx_defconfig @@ -5,7 +5,6 @@ CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_PROMPT="ac14xx> " CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/ap_sh4a_4a_defconfig b/configs/ap_sh4a_4a_defconfig index 75cf53fe21..41c8be9120 100644 --- a/configs/ap_sh4a_4a_defconfig +++ b/configs/ap_sh4a_4a_defconfig @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_CMD_ENV_EXISTS is not set # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set diff --git a/configs/apx4devkit_defconfig b/configs/apx4devkit_defconfig index e2061a2cce..5c30fe3ce7 100644 --- a/configs/apx4devkit_defconfig +++ b/configs/apx4devkit_defconfig @@ -14,14 +14,12 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_UBI=y diff --git a/configs/aria_defconfig b/configs/aria_defconfig index 963661ab2d..0f1432f9a8 100644 --- a/configs/aria_defconfig +++ b/configs/aria_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/aspenite_defconfig b/configs/aspenite_defconfig index 26654426ed..0ac39eabd2 100644 --- a/configs/aspenite_defconfig +++ b/configs/aspenite_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set # CONFIG_CMD_NET is not set # CONFIG_CMD_NFS is not set diff --git a/configs/cam5200_defconfig b/configs/cam5200_defconfig index 92985ab3d6..46a24f56ab 100644 --- a/configs/cam5200_defconfig +++ b/configs/cam5200_defconfig @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_MAC_PARTITION=y CONFIG_DOS_PARTITION=y CONFIG_ISO_PARTITION=y diff --git a/configs/cam5200_niosflash_defconfig b/configs/cam5200_niosflash_defconfig index 32bc58ee9b..6b9877ff21 100644 --- a/configs/cam5200_niosflash_defconfig +++ b/configs/cam5200_niosflash_defconfig @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_MAC_PARTITION=y CONFIG_DOS_PARTITION=y CONFIG_ISO_PARTITION=y diff --git a/configs/charon_defconfig b/configs/charon_defconfig index ec22a6368f..8a1429037a 100644 --- a/configs/charon_defconfig +++ b/configs/charon_defconfig @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/cm5200_defconfig b/configs/cm5200_defconfig index 7d8d01aaaa..d3369f4455 100644 --- a/configs/cm5200_defconfig +++ b/configs/cm5200_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5 CONFIG_SILENT_CONSOLE=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/digsy_mtc_RAMBOOT_defconfig b/configs/digsy_mtc_RAMBOOT_defconfig index 0d11eec75a..86b2b0d804 100644 --- a/configs/digsy_mtc_RAMBOOT_defconfig +++ b/configs/digsy_mtc_RAMBOOT_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_defconfig b/configs/digsy_mtc_defconfig index dc17ab4406..85b7f850f7 100644 --- a/configs/digsy_mtc_defconfig +++ b/configs/digsy_mtc_defconfig @@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_rev5_RAMBOOT_defconfig b/configs/digsy_mtc_rev5_RAMBOOT_defconfig index 4ab11c755b..7ec8650aca 100644 --- a/configs/digsy_mtc_rev5_RAMBOOT_defconfig +++ b/configs/digsy_mtc_rev5_RAMBOOT_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_rev5_defconfig b/configs/digsy_mtc_rev5_defconfig index 1f3f3c8bb6..b4b8533063 100644 --- a/configs/digsy_mtc_rev5_defconfig +++ b/configs/digsy_mtc_rev5_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/fo300_defconfig b/configs/fo300_defconfig index b4f334a436..00418153be 100644 --- a/configs/fo300_defconfig +++ b/configs/fo300_defconfig @@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/gplugd_defconfig b/configs/gplugd_defconfig index 97bb976803..f44b68dae8 100644 --- a/configs/gplugd_defconfig +++ b/configs/gplugd_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_SETEXPR is not set diff --git a/configs/ipek01_defconfig b/configs/ipek01_defconfig index cac9326b6c..690bc0f461 100644 --- a/configs/ipek01_defconfig +++ b/configs/ipek01_defconfig @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5 # CONFIG_CONSOLE_MUX is not set CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y diff --git a/configs/m28evk_defconfig b/configs/m28evk_defconfig index 6acbd77d5f..0ab7f6bb3c 100644 --- a/configs/m28evk_defconfig +++ b/configs/m28evk_defconfig @@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y CONFIG_CMD_SPI=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y CONFIG_CMD_GPIO=y CONFIG_CMD_DHCP=y diff --git a/configs/mecp5123_defconfig b/configs/mecp5123_defconfig index ebf5415464..db52077e1a 100644 --- a/configs/mecp5123_defconfig +++ b/configs/mecp5123_defconfig @@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig index 91384a6259..5040ea5742 100644 --- a/configs/motionpro_defconfig +++ b/configs/motionpro_defconfig @@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n" CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b" CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y CONFIG_CMD_BEDBUG=y CONFIG_LED_STATUS=y diff --git a/configs/mpc5121ads_defconfig b/configs/mpc5121ads_defconfig index c0af8127b5..47c4e5ace7 100644 --- a/configs/mpc5121ads_defconfig +++ b/configs/mpc5121ads_defconfig @@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y diff --git a/configs/mpc5121ads_rev2_defconfig b/configs/mpc5121ads_rev2_defconfig index ad46e02e94..ef700d0773 100644 --- a/configs/mpc5121ads_rev2_defconfig +++ b/configs/mpc5121ads_rev2_defconfig @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y diff --git a/configs/pcm030_LOWBOOT_defconfig b/configs/pcm030_LOWBOOT_defconfig index d19908ca8f..2933326e5d 100644 --- a/configs/pcm030_LOWBOOT_defconfig +++ b/configs/pcm030_LOWBOOT_defconfig @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000" CONFIG_BOOTDELAY=3 -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y diff --git a/configs/pcm030_defconfig b/configs/pcm030_defconfig index ef5c85888c..ff9f4e9f4f 100644 --- a/configs/pcm030_defconfig +++ b/configs/pcm030_defconfig @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="uboot> " -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y diff --git a/configs/pdm360ng_defconfig b/configs/pdm360ng_defconfig index f45a90caf9..4ef0df1aa8 100644 --- a/configs/pdm360ng_defconfig +++ b/configs/pdm360ng_defconfig @@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y # CONFIG_CONSOLE_MUX is not set CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y # CONFIG_PCI is not set diff --git a/configs/r0p7734_defconfig b/configs/r0p7734_defconfig index c5c3d52718..91b08dc24f 100644 --- a/configs/r0p7734_defconfig +++ b/configs/r0p7734_defconfig @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_CMD_ENV_EXISTS is not set # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig index db4c47c3d2..18dc039d93 100644 --- a/configs/v38b_defconfig +++ b/configs/v38b_defconfig @@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y CONFIG_TARGET_V38B=y CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y CONFIG_MAC_PARTITION=y diff --git a/include/common.h b/include/common.h index 83e4037a86..45f190a600 100644 --- a/include/common.h +++ b/include/common.h @@ -499,9 +499,19 @@ void reset_phy (void); void fdc_hw_init (void); /* $(BOARD)/eeprom.c */ +#ifdef CONFIG_CMD_EEPROM void eeprom_init (int bus); int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); +#else +/* + * Some EEPROM code is depecated because it used the legacy I2C interface. Add + * some macros here so we don't have to touch every one of those uses + */ +#define eeprom_init(bus) +#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS) +#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS) +#endif /* * Set this up regardless of board diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h index 1817571efe..7b162cccef 100644 --- a/include/configs/M54418TWR.h +++ b/include/configs/M54418TWR.h @@ -166,7 +166,6 @@ /* I2c */ #undef CONFIG_SYS_FSL_I2C -#undef CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SPEED 80000 diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 13f4ef67e1..19e0b1be1b 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -124,8 +124,7 @@ #ifndef CONFIG_CAM5200 /* POST support */ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) + CONFIG_SYS_POST_CPU) #endif #ifdef CONFIG_POST @@ -144,7 +143,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO @@ -279,54 +277,6 @@ #endif /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-Boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * HW-Monitor configuration on Mini-FAP - */ -#if defined (CONFIG_MINIFAP) -#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C -#endif - -/* List of I2C addresses to be verified by POST */ -#if defined (CONFIG_MINIFAP) -#undef CONFIG_SYS_POST_I2C_ADDRS -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_HWMON_ADDR, \ - CONFIG_SYS_I2C_SLAVE} -#endif - -/* * Flash configuration */ #define CONFIG_SYS_FLASH_BASE 0xFC000000 @@ -545,18 +495,6 @@ #endif /* - * RTC configuration - */ -#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100) -# define CONFIG_RTC_M41T11 1 -# define CONFIG_SYS_I2C_RTC_ADDR 0x68 -# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base - year */ -#else -# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ -#endif - -/* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h index 79099518e7..2ea43ffce1 100644 --- a/include/configs/a4m072.h +++ b/include/configs/a4m072.h @@ -81,7 +81,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #if defined(CONFIG_PCI) @@ -146,25 +145,6 @@ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_EEPROM_WREN 1 -#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4 - -/* * Flash configuration */ #define CONFIG_SYS_FLASH_BASE 0xFE000000 diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h index ee015bb83d..2a46e9b864 100644 --- a/include/configs/ac14xx.h +++ b/include/configs/ac14xx.h @@ -336,29 +336,12 @@ #define CONFIG_CMDLINE_EDITING 1 /* command line history */ -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS - -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration for Atmel AT24C01: - * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -384,7 +367,6 @@ #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h index 5f5882dc8e..d3d72b634d 100644 --- a/include/configs/ap_sh4a_4a.h +++ b/include/configs/ap_sh4a_4a.h @@ -35,20 +35,6 @@ #define CONFIG_BITBANGMII #define CONFIG_BITBANGMII_MULTI -/* I2C */ -#define CONFIG_SH_SH7734_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 0 -#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x50 -#define CONFIG_SH_I2C_DATA_HIGH 4 -#define CONFIG_SH_I2C_DATA_LOW 5 -#define CONFIG_SH_I2C_CLOCK 500000000 -#define CONFIG_SH_I2C_BASE0 0xFFC70000 -#define CONFIG_SH_I2C_BASE1 0xFFC71000 - /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h index a4c7847dab..cce39f27c7 100644 --- a/include/configs/apx4devkit.h +++ b/include/configs/apx4devkit.h @@ -79,12 +79,6 @@ #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #endif -/* RTC */ -#ifdef CONFIG_CMD_DATE -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 -#endif - /* Boot Linux */ #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTCOMMAND "run bootcmd_nand" diff --git a/include/configs/aria.h b/include/configs/aria.h index 94f6605d46..4d946fc44a 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -340,32 +340,12 @@ #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS - -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#endif - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration for Atmel AT24C32A-10TQ-2.7: - * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -392,7 +372,6 @@ #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/axs10x.h b/include/configs/axs10x.h index 768e8fbfa4..66e8cd5e9a 100644 --- a/include/configs/axs10x.h +++ b/include/configs/axs10x.h @@ -100,7 +100,7 @@ /* * Environment settings */ -#define CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_SIZE SZ_512 #define CONFIG_ENV_OFFSET 0 diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h index 0073cb5373..3a7d826837 100644 --- a/include/configs/cm5200.h +++ b/include/configs/cm5200.h @@ -44,7 +44,7 @@ /* * POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C) +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU) #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) /* List of I2C addresses to be verified by POST */ #define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \ @@ -200,16 +200,6 @@ "-(config)" /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ -#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x0 -#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */ -#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */ - -/* * RTC configuration */ #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h index 2b56945dd9..ab546c50cd 100644 --- a/include/configs/digsy_mtc.h +++ b/include/configs/digsy_mtc.h @@ -85,7 +85,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_PCI @@ -206,36 +205,6 @@ #define CONFIG_BOOTCOMMAND "run mtcb_start" /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_MODULE 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#if defined(CONFIG_DIGSY_REV5) -#define CONFIG_SYS_I2C_RTC_ADDR 0x56 -#define CONFIG_RTC_RV3029 -/* Enable 5k Ohm trickle charge resistor */ -#define CONFIG_SYS_RV3029_TCR 0x20 -#else -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */ -#endif - -/* * Flash configuration */ #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h index 6b6bbbd5c0..7ffc9d1dd9 100644 --- a/include/configs/ids8313.h +++ b/include/configs/ids8313.h @@ -165,7 +165,6 @@ #define CONFIG_TSEC2 #define CONFIG_TSEC_ENET #define CONFIG_HARD_SPI -#define CONFIG_HARD_I2C /* * NOR FLASH setup diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h index aff4adf5d0..ece72c6aa1 100644 --- a/include/configs/ipek01.h +++ b/include/configs/ipek01.h @@ -150,29 +150,6 @@ #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 4) -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* - * RTC configuration - */ -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - #define CONFIG_SYS_FLASH_BASE 0xFC000000 #define CONFIG_SYS_FLASH_SIZE 0x01000000 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h index 0d97317c7f..4461623118 100644 --- a/include/configs/jupiter.h +++ b/include/configs/jupiter.h @@ -127,25 +127,6 @@ #define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" #endif -#if 0 -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 -#endif - /* * Flash configuration */ diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index f6fa599e6b..c4717238bb 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -16,7 +16,6 @@ /* U-Boot Commands */ #define CONFIG_FAT_WRITE -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_NAND_TRIMFFS @@ -63,11 +62,6 @@ #define CONFIG_FEC_MXC #endif -/* EEPROM */ -#ifdef CONFIG_CMD_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#endif - /* RTC */ #ifdef CONFIG_CMD_DATE /* Use the internal RTC in the MXS chip */ diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h new file mode 100644 index 0000000000..68874dc029 --- /dev/null +++ b/include/configs/manroland/mpc5200-common.h @@ -0,0 +1,176 @@ +/* + * (C) Copyright 2009 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __MANROLAND_MPC52XX__COMMON_H +#define __MANROLAND_MPC52XX__COMMON_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC5200 1 /* MPC5200 CPU */ + +/* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\ + 230400 } + +#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */ +# define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xFF800000 + +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ + +#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI_AMD_RESET + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */ +#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */ + +/* Settings for XLB = 132 MHz */ +#define SDRAM_DDR 1 +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714f0f00 +#define SDRAM_CONFIG1 0x73722930 +#define SDRAM_CONFIG2 0x47770000 +#define SDRAM_TAPDELAY 0x10000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE +#else +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10) +#define CONFIG_SYS_MALLOC_LEN (512 << 10) +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII 1 + +/*use Hardware WDT */ +#define CONFIG_HW_WATCHDOG + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE + +/* 8Mbit SRAM @0x80100000 */ +#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ + +#define CONFIG_IDE_PREINIT 1 + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#define CONFIG_ATAPI 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" +#define CONFIG_OF_IDE_FIXUP + +#endif /* __MANROLAND_MPC52XX__COMMON_H */ diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h index 1a9cb675df..fe94e663c5 100644 --- a/include/configs/mecp5123.h +++ b/include/configs/mecp5123.h @@ -241,27 +241,12 @@ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ -#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */ - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -280,7 +265,7 @@ /* * Environment */ -#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */ +#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */ #define CONFIG_ENV_SIZE 0x1000 #define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */ @@ -288,7 +273,6 @@ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ #define CONFIG_CMD_REGINFO -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 136db0dd26..cb5c346807 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -34,7 +34,6 @@ * Command line configuration. */ #define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP #define CONFIG_CMD_JFFS2 @@ -256,21 +255,6 @@ #define CONFIG_SYS_ATA_STRIDE 4 /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ - -/* * RTC configuration */ #define CONFIG_RTC_DS1337 1 @@ -284,12 +268,6 @@ #define LED_ON 0x00000010 /* - * Temperature sensor - */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS { 0x49 } - -/* * Environment settings */ #define CONFIG_ENV_IS_IN_FLASH 1 diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h index dafb724e3f..f3961a6f35 100644 --- a/include/configs/mpc5121ads.h +++ b/include/configs/mpc5121ads.h @@ -327,29 +327,12 @@ #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#endif - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ - -/* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 @@ -396,7 +379,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO diff --git a/include/configs/mxs.h b/include/configs/mxs.h index fdf596f82f..c403dda483 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -126,16 +126,6 @@ #endif #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXS -#define CONFIG_HARD_I2C -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 400000 -#endif -#endif - /* LCD */ #ifdef CONFIG_VIDEO #define CONFIG_VIDEO_MXS diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h index e2881a7177..1b4200bcbf 100644 --- a/include/configs/o2dnt-common.h +++ b/include/configs/o2dnt-common.h @@ -68,7 +68,6 @@ /* * Supported commands */ -#define CONFIG_CMD_EEPROM #ifdef CONFIG_PCI #define CONFIG_CMD_PCI #endif @@ -173,27 +172,6 @@ #endif /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration: - * - * O2DNT board is equiped with Ramtron FRAM device FM24CL16 - * 16 Kib Ferroelectric Nonvolatile serial RAM memory - * organized as 2048 x 8 bits and addressable as eight I2C devices - * 0x50 ... 0x57 each 256 bytes in size - * - */ -#define CONFIG_SYS_I2C_FRAM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -/* * There is no write delay with FRAM, write operations are performed at bus * speed. Thus, no status polling or write delay is needed. */ diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h index 6d8a2338a2..406f3e547a 100644 --- a/include/configs/pcm030.h +++ b/include/configs/pcm030.h @@ -49,7 +49,6 @@ Serial console configuration /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_PCI @@ -121,31 +120,6 @@ IPB Bus clocking configuration. #define CONFIG_SYS_XLB_PIPELINING 1 /*--------------------------------------------------------------------------- - I2C configuration ----------------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/*--------------------------------------------------------------------------- - EEPROM CAT24WC32 configuration ----------------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ -#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_SIZE 2048 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 - -/*--------------------------------------------------------------------------- -RTC configuration ----------------------------------------------------------------------------*/ -#define RTC -#define CONFIG_RTC_PCF8563 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/*--------------------------------------------------------------------------- Flash configuration ---------------------------------------------------------------------------*/ @@ -172,11 +146,10 @@ RTC configuration Environment settings ---------------------------------------------------------------------------*/ -/* pcm030 ships with environment is EEPROM by default */ -#define CONFIG_ENV_IS_IN_EEPROM 1 +#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ /*beginning of the EEPROM */ -#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE +#define CONFIG_ENV_SIZE 2048 #define CONFIG_ENV_OVERWRITE 1 diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h index 501611dde7..4bd8236b33 100644 --- a/include/configs/pdm360ng.h +++ b/include/configs/pdm360ng.h @@ -302,34 +302,11 @@ #define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400 /* - * I2C - */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM /* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */ - -/* - * MAC addr in EEPROM - */ -#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10 -/* * Enabled only to delete "ethaddr" before testing * "ethaddr" setting from EEPROM */ @@ -345,12 +322,6 @@ #define CONFIG_HAS_ETH0 /* - * Configure on-board RTC - */ -#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 @@ -367,7 +338,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_REGINFO #undef CONFIG_CMD_FUSE diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h index 642572fc95..b159b1ed8d 100644 --- a/include/configs/r0p7734.h +++ b/include/configs/r0p7734.h @@ -40,20 +40,6 @@ # define CONFIG_SMC911X_BASE (0x84000000) #endif -/* I2C */ -#define CONFIG_SH_SH7734_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 0 -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x50 -#define CONFIG_SH_I2C_DATA_HIGH 4 -#define CONFIG_SH_I2C_DATA_LOW 5 -#define CONFIG_SH_I2C_CLOCK 500000000 -#define CONFIG_SH_I2C_BASE0 0xFFC70000 -#define CONFIG_SH_I2C_BASE1 0xFFC7100 - /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/s32v234evb.h b/include/configs/s32v234evb.h index 398b3aa343..33487cd86f 100644 --- a/include/configs/s32v234evb.h +++ b/include/configs/s32v234evb.h @@ -97,16 +97,6 @@ #define CONFIG_PHY_MICREL #endif -#if 0 /* Disable until the I2C driver will be updated */ - -/* I2C Configs */ -#define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MXC -#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR -#define CONFIG_SYS_I2C_SPEED 100000 -#endif - #if 0 /* Disable until the FLASH will be implemented */ #define CONFIG_SYS_USE_NAND #endif diff --git a/include/configs/v38b.h b/include/configs/v38b.h index cc0007827d..0bc0ae517a 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -135,27 +135,6 @@ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/* * Flash configuration - use CFI driver */ #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |