powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x

There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>

2 files changed, 0 insertions, 86 deletions

diff --git a/post/board/pdm360ng/Makefile b/post/board/pdm360ng/Makefile
deleted file mode 100644
index 9aa96a1f6a..0000000000
--- a/post/board/pdm360ng/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2010 DENX Software Engineering
-# Anatolij Gustschin, agust@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y += coproc_com.o
diff --git a/post/board/pdm360ng/coproc_com.c b/post/board/pdm360ng/coproc_com.c
deleted file mode 100644
index e11b69bdc7..0000000000
--- a/post/board/pdm360ng/coproc_com.c
+++ /dev/null
@@ -1,78 +0,0 @@
-/*
- * (C) Copyright 2010 DENX Software Engineering,
- * Anatolij Gustschin, agust@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Co-Processor communication POST
- */
-#include <common.h>
-#include <post.h>
-#include <serial.h>
-
-/*
- * Actually the termination sequence of the coprocessor
- * commands is "\r\n" (CR LF), but here we use a side effect of
- * the putc() routine of the serial driver which checks for LF
- * and sends CR before sending LF. Therefore the termination
- * sequence in the command below is only "\n".
- * "alive" string is the coprocessor response for ping command
- * and not a command, therefore it is terminated with "\r\n".
- */
-char alive[] = "$AL;38\r\n";
-char ping[] = "$PI;2C\n";
-
-int coprocessor_post_test(int flags)
-{
-	struct stdio_dev *cop_port;
-	int ret;
-	char buf[10];
-
-	/* Test IO Coprocessor communication */
-	cop_port = open_port(4, CONFIG_SYS_PDM360NG_COPROC_BAUDRATE);
-	if (!cop_port)
-		return -1;
-
-	write_port(cop_port, ping);
-	udelay(CONFIG_SYS_PDM360NG_COPROC_READ_DELAY);
-
-	memset(buf, 0, sizeof(buf));
-	ret = read_port(cop_port, buf, sizeof(buf));
-	close_port(4);
-	if (ret <= 0) {
-		post_log("Error: Can't read IO Coprocessor port.\n");
-		return -1;
-	}
-
-	if (strcmp(buf, alive)) {
-		post_log("Error: IO-Cop. resp.: %s\n", buf);
-		return -1;
-	}
-
-	/* Test WD Coprocessor communication */
-	cop_port = open_port(1, CONFIG_SYS_PDM360NG_COPROC_BAUDRATE);
-	if (!cop_port) {
-		post_log("Error: Can't open WD Coprocessor port.\n");
-		return -1;
-	}
-
-	write_port(cop_port, ping);
-	udelay(CONFIG_SYS_PDM360NG_COPROC_READ_DELAY);
-
-	memset(buf, 0, sizeof(buf));
-	ret = read_port(cop_port, buf, sizeof(buf));
-	close_port(1);
-	if (ret <= 0) {
-		post_log("Error: Can't read WD Coprocessor port.\n");
-		return -1;
-	}
-
-	if (strcmp(buf, alive)) {
-		post_log("Error: WD-Cop. resp.: %s\n", buf);
-		return -1;
-	}
-
-	return 0;
-}