armv8: ls1046ardb: Add LS1046ARDB board support

LS1046ARDB Specification:
-------------------------
Memory subsystem:
 * 8GByte DDR4 SDRAM (64bit bus)
 * 512 Mbyte NAND flash
 * Two 64 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card
 * On-board 4G eMMC

Ethernet:
 * Two XFI 10G ports
 * Two SGMII ports
 * Two RGMII ports

PCIe:
 * PCIe1 (SerDes2 Lane0) to miniPCIe slot
 * PCIe2 (SerDes2 Lane1) to x2 PCIe slot
 * PCIe3 (SerDes2 Lane2) to x4 PCIe slot

SATA:
 * SerDes2 Lane3 to SATA port

USB 3.0: one super speed USB 3.0 type A port
	 one Micro-AB port

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

1 files changed, 240 insertions, 0 deletions

diff --git a/include/configs/ls1046ardb.h b/include/configs/ls1046ardb.h
new file mode 100644
index 0000000000..693cc8d87f
--- /dev/null
+++ b/include/configs/ls1046ardb.h
@@ -0,0 +1,240 @@
+/*
+ * Copyright 2016 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1046ARDB_H__
+#define __LS1046ARDB_H__
+
+#include "ls1046a_common.h"
+
+#if defined(CONFIG_FSL_LS_PPA)
+#define CONFIG_ARMV8_PSCI
+#define CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
+#define CONFIG_SYS_LS_PPA_DRAM_BLOCK_MIN_SIZE		(1UL * 1024 * 1024)
+
+#define CONFIG_SYS_LS_PPA_FW_IN_XIP
+#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
+#define	CONFIG_SYS_LS_PPA_FW_ADDR	0x40500000
+#endif
+#endif
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#ifdef CONFIG_SD_BOOT
+#define CONFIG_SYS_TEXT_BASE		0x82000000
+#else
+#define CONFIG_SYS_TEXT_BASE		0x40100000
+#endif
+
+#define CONFIG_SYS_CLK_FREQ		100000000
+#define CONFIG_DDR_CLK_FREQ		100000000
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL	4
+#define CONFIG_NR_DRAM_BANKS		2
+
+#define CONFIG_DDR_SPD
+#define SPD_EEPROM_ADDRESS		0x51
+#define CONFIG_SYS_SPD_BUS_NUM		0
+
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE           0xdeadbeef
+#define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
+#define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
+#endif
+
+#ifdef CONFIG_SD_BOOT
+#ifdef CONFIG_EMMC_BOOT
+#define CONFIG_SYS_FSL_PBL_RCW \
+	board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
+#else
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
+#endif
+#endif
+
+/* No NOR flash */
+#define CONFIG_SYS_NO_FLASH
+
+/* IFC */
+#define CONFIG_FSL_IFC
+
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE		0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8	\
+				| CSPR_MSEL_NAND	\
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
+				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
+				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
+				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x7) | \
+					FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0xe)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
+					FTIM2_NAND_TREH(0xa) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+/*
+ * CPLD
+ */
+#define CONFIG_SYS_CPLD_BASE		0x7fb00000
+#define CPLD_BASE_PHYS			CONFIG_SYS_CPLD_BASE
+
+#define CONFIG_SYS_CPLD_CSPR_EXT	(0x0)
+#define CONFIG_SYS_CPLD_CSPR		(CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
+					CSPR_PORT_SIZE_8 | \
+					CSPR_MSEL_GPCM | \
+					CSPR_V)
+#define CONFIG_SYS_CPLD_AMASK		IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CPLD_CSOR		CSOR_NOR_ADM_SHIFT(16)
+
+/* CPLD Timing parameters for IFC GPCM */
+#define CONFIG_SYS_CPLD_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CPLD_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
+					FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CPLD_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
+					FTIM2_GPCM_TCH(0xf) | \
+					FTIM2_GPCM_TWP(0x3E))
+#define CONFIG_SYS_CPLD_FTIM3		0x0
+
+/* IFC Timing Params */
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_CPLD_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_CPLD_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_CPLD_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_CPLD_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_CPLD_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_CPLD_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_CPLD_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_CPLD_FTIM3
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM		0
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x53
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+#define I2C_RETIMER_ADDR			0x18
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_OFFSET		(1024 * 1024)
+#define CONFIG_ENV_SIZE			0x2000
+#else
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE			0x2000		/* 8KB */
+#define CONFIG_ENV_OFFSET		0x200000	/* 2MB */
+#define CONFIG_ENV_SECT_SIZE		0x40000		/* 256KB */
+#endif
+
+/* FMan */
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_AQUANTIA
+#define AQR105_IRQ_MASK			0x80000000
+
+#define RGMII_PHY1_ADDR			0x1
+#define RGMII_PHY2_ADDR			0x2
+
+#define SGMII_PHY1_ADDR			0x3
+#define SGMII_PHY2_ADDR			0x4
+
+#define FM1_10GEC1_PHY_ADDR		0x0
+
+#define CONFIG_ETHPRIME			"FM1@DTSEC3"
+#endif
+
+/* QSPI device */
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE		(1 << 26)
+#define FSL_QSPI_FLASH_NUM		2
+#define CONFIG_SPI_FLASH_BAR
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_BOOTCOMMAND		"sf probe 0:0;sf read $kernel_load" \
+					"$kernel_start $kernel_size;" \
+					"bootm $kernel_load"
+
+#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:1m(rcw)," \
+			"15m(u-boot),48m(kernel.itb);" \
+			"7e800000.flash:16m(nand_uboot)," \
+			"48m(nand_kernel),448m(nand_free)"
+
+#endif /* __LS1046ARDB_H__ */