integrator: rewrite the AP PCI driver

The PCI support for the Integrator AP has apparently never
been finished and I strongly suspect that it has never worked,
so let's fix it. This is a list of the more or less
un-splittable changes done in this driver rewrite:

- Replace the register definitions stashed into the config
  file (!) with a copy if the register file from the Linux
  kernels arch/arm/include/asm/hardware/pci_v3.h

- Delete the unreadable gigantic macros that perform the
  config accesses and replace them with copyedited code from
  Linux arch/arm/mach-integrator/pci_v3.c

- Rewrite the rest of the setup code to use the
  v3_[read|write][lwb]() accessors.

- Enable PCI by default in the AP board configuration.

- Fix checkpatch warnings and make code more conformant.

Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 6 insertions, 142 deletions

diff --git a/include/configs/integratorap.h b/include/configs/integratorap.h
index a1fdbb8140..0a704cb248 100644
--- a/include/configs/integratorap.h
+++ b/include/configs/integratorap.h
@@ -82,17 +82,7 @@
 /*
  * Command line configuration.
  */
-
-
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMLS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_LOADS
-
+#include <config_cmd_default.h>
 
 #define CONFIG_BOOTDELAY	2
 #define CONFIG_BOOTARGS		"root=/dev/mtdblock0 console=ttyAM0 console=tty"
@@ -157,142 +147,16 @@
  * PCI definitions
  */
 
-#ifdef CONFIG_PCI			/* pci support	*/
-#undef CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
-#define DEBUG
+#define CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_PCI_PNP
 
+#define CONFIG_NET_MULTI
+#define CONFIG_TULIP
 #define CONFIG_EEPRO100
 #define CONFIG_SYS_RX_ETH_BUFFER	8	/* use 8 rx buffer on eepro100	*/
 
-#define INTEGRATOR_BOOT_ROM_BASE	0x20000000
-#define INTEGRATOR_HDR0_SDRAM_BASE	0x80000000
-
-/* PCI Base area */
-#define INTEGRATOR_PCI_BASE		0x40000000
-#define INTEGRATOR_PCI_SIZE		0x3FFFFFFF
-
-/* memory map as seen by the CPU on the local bus */
-#define CPU_PCI_IO_ADRS		0x60000000	/* PCI I/O space base */
-#define CPU_PCI_IO_SIZE		0x10000
-
-#define CPU_PCI_CNFG_ADRS	0x61000000	/* PCI config space */
-#define CPU_PCI_CNFG_SIZE	0x1000000
-
-#define PCI_MEM_BASE		0x40000000   /* 512M to xxx */
-/*  unused 256M from A0000000-AFFFFFFF might be used for I2O ??? */
-#define INTEGRATOR_PCI_IO_BASE	0x60000000   /* 16M to xxx */
-/*  unused (128-16)M from B1000000-B7FFFFFF */
-#define PCI_CONFIG_BASE		0x61000000   /* 16M to xxx */
-/*  unused ((128-16)M - 64K) from XXX */
-
-#define PCI_V3_BASE		0x62000000
-
-/* V3 PCI bridge controller */
-#define V3_BASE			0x62000000    /* V360EPC registers */
-
-#define PCI_ENET0_IOADDR	(CPU_PCI_IO_ADRS)
-#define PCI_ENET0_MEMADDR	(PCI_MEM_BASE)
-
-
-#define V3_PCI_VENDOR		0x00000000
-#define V3_PCI_DEVICE		0x00000002
-#define V3_PCI_CMD		0x00000004
-#define V3_PCI_STAT		0x00000006
-#define V3_PCI_CC_REV		0x00000008
-#define V3_PCI_HDR_CF		0x0000000C
-#define V3_PCI_IO_BASE		0x00000010
-#define V3_PCI_BASE0		0x00000014
-#define V3_PCI_BASE1		0x00000018
-#define V3_PCI_SUB_VENDOR	0x0000002C
-#define V3_PCI_SUB_ID		0x0000002E
-#define V3_PCI_ROM		0x00000030
-#define V3_PCI_BPARAM		0x0000003C
-#define V3_PCI_MAP0		0x00000040
-#define V3_PCI_MAP1		0x00000044
-#define V3_PCI_INT_STAT		0x00000048
-#define V3_PCI_INT_CFG		0x0000004C
-#define V3_LB_BASE0		0x00000054
-#define V3_LB_BASE1		0x00000058
-#define V3_LB_MAP0		0x0000005E
-#define V3_LB_MAP1		0x00000062
-#define V3_LB_BASE2		0x00000064
-#define V3_LB_MAP2		0x00000066
-#define V3_LB_SIZE		0x00000068
-#define V3_LB_IO_BASE		0x0000006E
-#define V3_FIFO_CFG		0x00000070
-#define V3_FIFO_PRIORITY	0x00000072
-#define V3_FIFO_STAT		0x00000074
-#define V3_LB_ISTAT		0x00000076
-#define V3_LB_IMASK		0x00000077
-#define V3_SYSTEM		0x00000078
-#define V3_LB_CFG		0x0000007A
-#define V3_PCI_CFG		0x0000007C
-#define V3_DMA_PCI_ADR0		0x00000080
-#define V3_DMA_PCI_ADR1		0x00000090
-#define V3_DMA_LOCAL_ADR0	0x00000084
-#define V3_DMA_LOCAL_ADR1	0x00000094
-#define V3_DMA_LENGTH0		0x00000088
-#define V3_DMA_LENGTH1		0x00000098
-#define V3_DMA_CSR0		0x0000008B
-#define V3_DMA_CSR1		0x0000009B
-#define V3_DMA_CTLB_ADR0	0x0000008C
-#define V3_DMA_CTLB_ADR1	0x0000009C
-#define V3_DMA_DELAY		0x000000E0
-#define V3_MAIL_DATA		0x000000C0
-#define V3_PCI_MAIL_IEWR	0x000000D0
-#define V3_PCI_MAIL_IERD	0x000000D2
-#define V3_LB_MAIL_IEWR		0x000000D4
-#define V3_LB_MAIL_IERD		0x000000D6
-#define V3_MAIL_WR_STAT		0x000000D8
-#define V3_MAIL_RD_STAT		0x000000DA
-#define V3_QBA_MAP		0x000000DC
-
-/* SYSTEM register bits */
-#define V3_SYSTEM_M_RST_OUT		(1 << 15)
-#define V3_SYSTEM_M_LOCK		(1 << 14)
-
-/*  PCI_CFG bits */
-#define V3_PCI_CFG_M_RETRY_EN		(1 << 10)
-#define V3_PCI_CFG_M_AD_LOW1		(1 << 9)
-#define V3_PCI_CFG_M_AD_LOW0		(1 << 8)
-
-/* PCI MAP register bits (PCI -> Local bus) */
-#define V3_PCI_MAP_M_MAP_ADR		0xFFF00000
-#define V3_PCI_MAP_M_RD_POST_INH	(1 << 15)
-#define V3_PCI_MAP_M_ROM_SIZE		(1 << 11 | 1 << 10)
-#define V3_PCI_MAP_M_SWAP		(1 << 9 | 1 << 8)
-#define V3_PCI_MAP_M_ADR_SIZE		0x000000F0
-#define V3_PCI_MAP_M_REG_EN		(1 << 1)
-#define V3_PCI_MAP_M_ENABLE		(1 << 0)
-
-/* 9 => 512M window size */
-#define V3_PCI_MAP_M_ADR_SIZE_512M	0x00000090
-
-/* A => 1024M window size */
-#define V3_PCI_MAP_M_ADR_SIZE_1024M	0x000000A0
-
-/* LB_BASE register bits (Local bus -> PCI) */
-#define V3_LB_BASE_M_MAP_ADR		0xFFF00000
-#define V3_LB_BASE_M_SWAP		(1 << 8 | 1 << 9)
-#define V3_LB_BASE_M_ADR_SIZE		0x000000F0
-#define V3_LB_BASE_M_PREFETCH		(1 << 3)
-#define V3_LB_BASE_M_ENABLE		(1 << 0)
-
-/* PCI COMMAND REGISTER bits */
-#define V3_COMMAND_M_FBB_EN		(1 << 9)
-#define V3_COMMAND_M_SERR_EN		(1 << 8)
-#define V3_COMMAND_M_PAR_EN		(1 << 6)
-#define V3_COMMAND_M_MASTER_EN		(1 << 2)
-#define V3_COMMAND_M_MEM_EN		(1 << 1)
-#define V3_COMMAND_M_IO_EN		(1 << 0)
-
-#define INTEGRATOR_SC_BASE		0x11000000
-#define INTEGRATOR_SC_PCIENABLE_OFFSET	0x18
-#define INTEGRATOR_SC_PCIENABLE \
-			(INTEGRATOR_SC_BASE + INTEGRATOR_SC_PCIENABLE_OFFSET)
 
-#endif /* CONFIG_PCI */
 /*-----------------------------------------------------------------------
  * There are various dependencies on the core module (CM) fitted
  * Users should refer to their CM user guide