Cleanup: fix "MHz" spelling

Signed-off-by: Wolfgang Denk <wd@denx.de>

10 files changed, 12 insertions, 12 deletions

diff --git a/cpu/ixp/npe/miiphy.c b/cpu/ixp/npe/miiphy.c
index c63c54e28f..20fee2d39c 100644
--- a/cpu/ixp/npe/miiphy.c
+++ b/cpu/ixp/npe/miiphy.c
@@ -32,7 +32,7 @@
   |  Date	 Description of Change					     BY
   |  ---------	 ---------------------					     ---
   |  05-May-99	 Created						     MKW
-  |  01-Jul-99	 Changed clock setting of sta_reg from 66Mhz to 50Mhz to
+  |  01-Jul-99	 Changed clock setting of sta_reg from 66MHz to 50MHz to
   |		 better match OPB speed. Also modified delay times.	     JWB
   |  29-Jul-99	 Added Full duplex support				     MKW
   |  24-Aug-99	 Removed printf from dp83843_duplex()			     JWB
diff --git a/cpu/mips/incaip_clock.c b/cpu/mips/incaip_clock.c
index d0515ca673..fc2c62180b 100644
--- a/cpu/mips/incaip_clock.c
+++ b/cpu/mips/incaip_clock.c
@@ -33,8 +33,8 @@
 *
 * RETURNS:
 *          150.000.000 for 150 MHz
-*          133.333.333 for 133 Mhz (= 400MHz/3)
-*          100.000.000 for 100 Mhz (= 400MHz/4)
+*          133.333.333 for 133 MHz (= 400MHz/3)
+*          100.000.000 for 100 MHz (= 400MHz/4)
 * NOTE:
 *   This functions should be used by the hardware driver to get the correct
 *   frequency of the CPU. Don't use the macros, which are set to init the CPU
diff --git a/cpu/mpc8220/i2cCore.c b/cpu/mpc8220/i2cCore.c
index accf43c102..b89ad034f4 100644
--- a/cpu/mpc8220/i2cCore.c
+++ b/cpu/mpc8220/i2cCore.c
@@ -440,7 +440,7 @@ STATUS i2c_write2byte (SI2C * pi2c, UINT16 * writeb)
 	return OK;
 }
 
-/* FDR table base on 33Mhz - more detail please refer to Odini2c_dividers.xls
+/* FDR table base on 33MHz - more detail please refer to Odini2c_dividers.xls
 FDR FDR scl sda scl2tap2
 510 432 tap tap tap tap scl_per	    sda_hold	I2C Freq    0	1   2	3   4	5
 000 000 9   3	4   1	28 Clocks   9 Clocks	1190 KHz    0	0   0	0   0	0
diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c
index 359a915586..42a4e675da 100644
--- a/cpu/mpc83xx/spd_sdram.c
+++ b/cpu/mpc83xx/spd_sdram.c
@@ -314,7 +314,7 @@ long int spd_sdram()
 			+ (spd.clk_cycle & 0x0f));
 	max_data_rate = max_bus_clk * 2;
 
-	debug("DDR:Module maximum data rate is: %dMhz\n", max_data_rate);
+	debug("DDR:Module maximum data rate is: %d MHz\n", max_data_rate);
 
 	ddrc_clk = gd->mem_clk / 1000000;
 	effective_data_rate = 0;
@@ -401,7 +401,7 @@ long int spd_sdram()
 		}
 	}
 
-	debug("DDR:Effective data rate is: %dMhz\n", effective_data_rate);
+	debug("DDR:Effective data rate is: %dMHz\n", effective_data_rate);
 	debug("DDR:The MSB 1 of CAS Latency is: %d\n", caslat);
 
 	/*
diff --git a/cpu/mpc8xx/fec.c b/cpu/mpc8xx/fec.c
index 141425d8ed..89c1ff939d 100644
--- a/cpu/mpc8xx/fec.c
+++ b/cpu/mpc8xx/fec.c
@@ -398,7 +398,7 @@ static void fec_pin_init(int fecidx)
 	 * * the MII management interface clock must be less than or equal
 	 * * to 2.5 MHz.
 	 * * This MDC frequency is equal to system clock / (2 * MII_SPEED).
-	 * * Then MII_SPEED = system_clock / 2 * 2,5 Mhz.
+	 * * Then MII_SPEED = system_clock / 2 * 2,5 MHz.
 	 *
 	 * All MII configuration is done via FEC1 registers:
 	 */
diff --git a/cpu/mpc8xx/serial.c b/cpu/mpc8xx/serial.c
index cae90ddaf5..bd90dcd3b0 100644
--- a/cpu/mpc8xx/serial.c
+++ b/cpu/mpc8xx/serial.c
@@ -70,7 +70,7 @@ static void serial_setdivisor(volatile cpm8xx_t *cp)
 	int divisor=(gd->cpu_clk + 8*gd->baudrate)/16/gd->baudrate;
 
 	if(divisor/16>0x1000) {
-		/* bad divisor, assume 50Mhz clock and 9600 baud */
+		/* bad divisor, assume 50MHz clock and 9600 baud */
 		divisor=(50*1000*1000 + 8*9600)/16/9600;
 	}
 
diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c
index eca92e83b7..e8871fc459 100644
--- a/cpu/ppc4xx/4xx_pci.c
+++ b/cpu/ppc4xx/4xx_pci.c
@@ -286,7 +286,7 @@ void pci_405gp_init(struct pci_controller *hose)
 #endif /* CONFIG_SYS_PCI_CLASSCODE */
 
 	/*--------------------------------------------------------------------------+
-	 * If PCI speed = 66Mhz, set 66Mhz capable bit.
+	 * If PCI speed = 66MHz, set 66MHz capable bit.
 	 *--------------------------------------------------------------------------*/
 	if (bd->bi_pci_busfreq >= 66000000) {
 		pci_read_config_word(PCIDEVID_405GP, PCI_STATUS, &temp_short);
diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c
index 84b1bbe54d..01710e71dd 100644
--- a/cpu/ppc4xx/miiphy.c
+++ b/cpu/ppc4xx/miiphy.c
@@ -301,7 +301,7 @@ static int emac_miiphy_command(u8 addr, u8 reg, int cmd, u16 value)
 
 	sta_reg = reg;		/* reg address */
 
-	/* set clock (50Mhz) and read flags */
+	/* set clock (50MHz) and read flags */
 #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \
     defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
     defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c
index d21bd82dc6..ed6e55b698 100644
--- a/cpu/ppc4xx/speed.c
+++ b/cpu/ppc4xx/speed.c
@@ -148,7 +148,7 @@ void get_sys_info (PPC4xx_SYS_INFO * sysInfo)
 		 * is equal to the 405GP SYS_CLK_FREQ. If not in bypass mode, check VCO
 		 * to make sure it is within the proper range.
 		 *    spec:    VCO = SYS_CLOCK x FBKDIV x PLBDIV x FWDDIV
-		 * Note freqVCO is calculated in Mhz to avoid errors introduced by rounding.
+		 * Note freqVCO is calculated in MHz to avoid errors introduced by rounding.
 		 */
 		if (sysInfo->pllFwdDiv == 1) {
 			sysInfo->freqProcessor = CONFIG_SYS_CLK_FREQ;
diff --git a/cpu/s3c44b0/cpu.c b/cpu/s3c44b0/cpu.c
index fd09bf9106..2960f2f3af 100644
--- a/cpu/s3c44b0/cpu.c
+++ b/cpu/s3c44b0/cpu.c
@@ -256,7 +256,7 @@ void i2c_init(int speed, int slaveaddr)
 
 	/*
 		Enable ACK, IICCLK=MCLK/16, enable interrupt
-		75Mhz/16/(12+1) = 390625 Hz
+		75MHz/16/(12+1) = 390625 Hz
 	*/
 	rIICCON=(1<<7)|(0<<6)|(1<<5)|(0xC);
 	IICCON = rIICCON;