powerpc/km: remove unmaintained target KMVECT1

Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 0 insertions, 81 deletions

diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c
index 880ce67fa6..a693845383 100644
--- a/board/keymile/km83xx/km83xx.c
+++ b/board/keymile/km83xx/km83xx.c
@@ -124,19 +124,10 @@ static int piggy_present(void)
 	return in_8(&base->bprth) & PIGGY_PRESENT;
 }
 
-#if defined(CONFIG_KMVECT1)
-int ethernet_present(void)
-{
-	/* ethernet port connected to simple switch without piggy */
-	return 1;
-}
-#else
 int ethernet_present(void)
 {
 	return piggy_present();
 }
-#endif
-
 
 int board_early_init_r(void)
 {
@@ -197,80 +188,8 @@ int misc_init_r(void)
 	return 0;
 }
 
-#if defined(CONFIG_KMVECT1)
-#include <mv88e6352.h>
-/* Marvell MV88E6122 switch configuration */
-static struct mv88e_sw_reg extsw_conf[] = {
-	/* port 1, FRONT_MDI, autoneg */
-	{ PORT(1), PORT_PHY, NO_SPEED_FOR },
-	{ PORT(1), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
-	{ PHY(1), PHY_1000_CTRL, NO_ADV },
-	{ PHY(1), PHY_SPEC_CTRL, AUTO_MDIX_EN },
-	{ PHY(1), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
-		FULL_DUPLEX },
-	/* port 2, unused */
-	{ PORT(2), PORT_CTRL, PORT_DIS },
-	{ PHY(2), PHY_CTRL, PHY_PWR_DOWN },
-	{ PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
-	/* port 3, BP_MII (CPU), PHY mode, 100BASE */
-	{ PORT(3), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
-	/* port 4, ESTAR to slot 11, SerDes, 1000BASE-X */
-	{ PORT(4), PORT_STATUS, NO_PHY_DETECT },
-	{ PORT(4), PORT_PHY, SPEED_1000_FOR },
-	{ PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
-	/* port 5, ESTAR to slot 13, SerDes, 1000BASE-X */
-	{ PORT(5), PORT_STATUS, NO_PHY_DETECT },
-	{ PORT(5), PORT_PHY, SPEED_1000_FOR },
-	{ PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
-	/*
-	 * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
-	 * acc . MV-S300889-00D.pdf , clause 4.5
-	 */
-	{ PORT(5), 0x1A, 0xADB1 },
-	/* port 6, unused, this port has no phy */
-	{ PORT(6), PORT_CTRL, PORT_DIS },
-	/*
-	 * Errata Fix: 1.9V Output from Internal 1.8V Regulator,
-	 * acc . MV-S300889-00D.pdf , clause 4.5
-	 */
-	{ PORT(5), 0x1A, 0xADB1 },
-};
-#endif
-
 int last_stage_init(void)
 {
-#if defined(CONFIG_KMVECT1)
-	struct km_bec_fpga __iomem *base =
-		(struct km_bec_fpga __iomem *)CONFIG_SYS_KMBEC_FPGA_BASE;
-	u8 tmp_reg;
-
-	/* Release mv88e6122 from reset */
-	tmp_reg = in_8(&base->res1[0]) | 0x10; /* DIRECT3 register */
-	out_8(&base->res1[0], tmp_reg);	       /* GP28 as output */
-	tmp_reg = in_8(&base->gprt3) | 0x10;   /* GP28 to high */
-	out_8(&base->gprt3, tmp_reg);
-
-	/* configure MV88E6122 switch */
-	char *name = "UEC2";
-
-	if (miiphy_set_current_dev(name))
-		return 0;
-
-	mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
-		ARRAY_SIZE(extsw_conf));
-
-	mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
-
-	if (piggy_present()) {
-		env_set("ethact", "UEC2");
-		env_set("netdev", "eth1");
-		puts("using PIGGY for network boot\n");
-	} else {
-		env_set("netdev", "eth0");
-		puts("using frontport for network boot\n");
-	}
-#endif
-
 #if defined(CONFIG_TARGET_KMCOGE5NE)
 	struct bfticu_iomap *base =
 		(struct bfticu_iomap *)CONFIG_SYS_BFTIC3_BASE;